Optoma Projector Ew762 User Manual

51English
Appendices
 Image is out of focus
 Make sure the lens cap is removed.
 Adjust the Focus Ring on the projector lens. 
 Make sure the projection screen is between the required distance. 
See page 16.
 The image is stretched when displaying 16:9 DVD title
 When you play anamorphic DVD or 16:9 DVD, the projector will 
show the best image when the projector display mode is set to 
16:9 in the OSD.
 If you play 4:3 format DVD titles, please change the format to 4:3 
in the projector OSD.
 If...

52English
Appendices
 The projector stops responding to all controls
 If possible, turn off the projector, then unplug the power cord and 
wait at least 60 seconds before reconnecting power.
 Check that “Keypad Lock” is not activated by trying to control the 
projector with the remote control.
 Lamp burns out or makes a popping sound
 When the lamp reaches its end of life, it will burn out and may 
make a loud popping sound. If this happens, the projector will not 
turn on until the lamp module has...

53English
Appendices
 On Screen Messages 
 Temperature warning:
 
 Fan failed:
 
 Lamp warning:
 
 Out of display range:
 
 If the remote control does not work
 Check the operating angle of the remote control is within ±15° both horizontally and vertically of one of the IR receivers on the projector.
 Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (±0°) of the projector.
 Make sure the batteries are inserted correctly.
 Replace batteries...

54English
Appendices
Replacing the lamp
The projector automatically detects the lamp life. When the 
lamp life is nearing the end of use, you will receive a warning 
message.
When you see this message, please contact your local reseller 
or service center to change the lamp as soon as possible. 
Make sure the projector has been cooled down for at least 30 
minutes before changing the lamp. 
 Warning: Lamp compartment may be hot! Allow it to cool 
down before changing the lamp!
 Warning: To reduce the...

55English
Appendices
Lamp Replacement Procedure:
1. Switch off the power to the projector by pressing the “” button. 
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Unscrew the two screws on the cover. 1
5. Lift up and remove the cover. 2
6. Unscrew the two screws on the lamp module. 3
7. Lift up the lamp handle and remove the lamp module slowly and carefully . 4
To replace the lamp module, reverse the previous steps.
8.  Turn on the projector and use “Lamp...

56English
Appendices
	For widescreen resolution (WXGA), the compatibility support is dependent on Notebook/PC models.
	120Hz input signals may be dependent on graphics cards support.
	Please note that using resolutions other than native 1024 x 768 (XGA model), 1280 x 800 (WXGA model) may result 
in some loss of image clarity.
Compatibility Modes
Computer Compatibility 
ModeResolutionAnglog/Digital
V-Sync (Hz)H-Sync (KHz)
VGA640 × 3507031.50
VGA640 × 3508537.90
VGA640 × 4008537.90
VGA640 × 4806031.50...

57English
Appendices
Video Compatibility
Computer Compatibility
ModeResolutionV-Sync (Hz)H-Sync (KHz)
MAC LC 13”640 × 48066.6634.98
MAC II 13”640 × 48066.6835.00
MAC 16”832 × 62474.5549.73
MAC 19”1024 × 7687560.24
MAC1152 × 87075.0668.68
MAC G4640 × 4806031.35
i MAC DV1024 × 7687560.00
i MAC DV1152 × 8707568.49
NTSCM (3.58MHz), 4.43 MHz
PALB, D, G, H, I, M, N
SECAMB, D, G, K, K1, L
SDTV480i/p@60Hz, 576i/p@50Hz 
HDTV720p@50Hz/60Hz, 1080i@50Hz/60Hz, 
1080p@24Hz/25Hz/30Hz/50Hz/60Hz
 
  

58English
Appendices
RS232 Pin Assignments
RS232 Commands and Protocol 
Function List
	RS232 shell is grounded.
Pin no.Spec.  (from projector side)
1N/A
2RXD
3TXD
4N/A
5GND
6N/A
7N/A
8N/A
9N/A
1
2
3
4
5
6
7
8
9   

59English
Appendices
RS232 Protocol Function List
Baud Rate : 9600
Data Bits: 8
Parity: None
Stop Bits: 1 
Flow Control : None
UART16550 FIFO: Disable
Projector Return (Pass): P
Projector Return (Fail): F 
1.  
There is a  after all ASCII commands. 2.   0D is the HEX code for  in ASCII code.
XX=00-99, projector's ID,
XX=00 is for all projectors  
Optoma EW762 RS232 Command Table....

60English
Appendices
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX44 n 7E 30 30 34 34 20  a 0D Color (Saturation) n = 0 (a=30) ~ 100 (a=31 30 30)
~XX45 n 7E 30 30 34 35 20  a 0D Tint n = 0 (a=30) ~ 100 (a=31 30 30)...