Optoma Projector EH505 User Manual

							61
Options | Advanced
Direct Power On
Enable or disable Direct Power On.
4 On—the projector powers on automatically when AC power is supplied.
4 Off— the projector must be powered on as normal.
Signal Power On
Enable or disable Signal Power On.
4 On—the projector powers on automatically when an active signal is dete\
cted.
4 Off— disable the power on trigger by active signal is detected.
1. Only available on Standby Mode is Active.
2.    If projector is turned off with keeping input the signal source (the last 
image source showing on screen), it will not re-start unless:
a. Terminate the last image source and input any signal source again.
b. Unplug and re-plug the projector power again.
3. Signal power on will ignore “source lock” setting.
Auto Power Off (min)
Set the Auto Power Off interval. The projector powers off the lamp after 
30 minutes of no signal by default. The following warning is displayed 60 
seconds before power off.
User Controls 
English   
						

							62
Options | Advanced
Sleep Timer (min)
Set  the  Sleep  Timer  interval.  The  projector  powers  off  after  the  specified 
time period of inactivity (regardless of signal). The following warning is 
displayed 60 seconds before power off.
Power Mode (Standby)4
 Eco.: Choose “Eco.” to save power dissipation further < 0.5W.
4 Active:   Choose “Active” to return to normal standby and the VGA 
out port will be enabled.
User Controls 
English   
						

							63
Options | Lamp Setting
Lamp Hour
Displays the number of hours the lamp has been active. This item is for \
display only.
Lamp Reset
After  replacing  the  lamp,  reset  the  lamp  counter  to  accurately  reflect  the 
new lamp’s life span.
1. Select Lamp Reset.A confirmation screen displays.
2. Select Yes to reset the lamp counter to zero.
Lamp Reminder
Enable or disable the lamp life span reminder. 
4 On—a warning message displays when remaining lamp life is less than 30 hours.
4 Off—no warning message displays.
User Controls 
English   
						

							64
Options | Lamp Setting
Brightness Mode
Select the lamp brightness mode.
4 Bright—the default setting.
4 Eco—lower brightness setting to conserve lamp life.
Power
Press ◄► to select the lamp mode for 370W brightness or 280W 
brightness to save lamp life. The function is only available when 
Brightness Mode is Power.
User Controls 
English   
						

							65
LAN_RJ45
For simplicity and ease of operation, the Optoma projector provides 
diverse networking and remote management features.
The LAN/RJ45 function of the projector through a network, such as 
remotely manage:  Power On/Off, Brightness and Contrast settings. Also, \
projector status information, such as: Video-Source, Sound-Mute, etc.
Wired LAN Terminal functionalites
The projector can be controlled by a PC (Laptop) or other external dev\
ice 
via LAN/RJ45 port and compatible with Crestron / Extron / AMX 
(Device Discovery) / PJLink.
4  Crestron is a registered trademark of Crestron Electronics, Inc. of the \
United 
States.
4  Extron is a registered trademark of Extron Electronics, Inc. of the Unit\
ed 
States.
4  AMX is a registered trademark of AMX LLC of the United States.
4  PJLink applied for trademark and logo registration in Japan, the United \
States of America, and other countries by JBMIA.
Supported External Devices
This projector is supported by the specified commands of the Crestron 
Electronics controller and related software (ex, RoomView®).
http://www.crestron.com/
This projector is compliant to support Extron device(s) for reference.\
 http://www.extron.com/
This projector is supported by AMX ( Device Discovery ). http://www.amx.com/
This projector supports all commands of PJLink Class1 (Version 1.00). http://pjlink.jbmia.or.jp/english/
For more detail of information about the diverse types of external devic\
es 
which can be connected to the LAN/RJ45 port and remote/control the 
projector, as well as the related control commands supporting for each 
external device, kindly please get contact with the Support-Service 
directly.
v Projector  connects to 
LAN, please 
use Ethernet 
Normal Cable.
v Peer-to-peer  (PC connects 
to Projector  
directly), 
please use 
Ethernet 
Crossover 
Cable.
User Controls 
English   
						

							66
LAN_RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop\
).
2. On the PC (Laptop), select Start -> Control Panel-> Network Connection\
s.
3. Right Click on your Local Area Connection, and select Property.
User Controls 
English   
						

							67
4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP).
5. Click Properties.
6. Fill in the IP address and Subnet mask, then press OK. 
User Controls 
English   
						

							68
7. Press the Menu button on the projector.
8. Select OSD-> SETUP-> Network Settings-> Lan Settings.
9. After getting into Network Status, input the following:
4 DHCP: Off
4 IP Address:  10.10.10.10
4 Subnet Mask:  255.255.255.0
4 Gateway:  0.0.0.0
4 DNS:  0.0.0.0
10. Press  (Enter) / ► to confirm settings.
11. Open a web browser (ex, Microsoft Internet Explorer with Adobe  Flash Player 9.0 or higher).
12. In the Address bar, input the IP address: 10.10.10.10. 
13. Press  (Enter) / ►.
The projector is setup for remote management. The LAN/RJ45 function 
displays as follows.
v For more   information, 
please visit 
http://www.
crestron.com
User Controls 
English   
						

							69
CategoryItemInput-Length
Crestron Control IP Address
15
IP ID 3
Port 5
Projector Projector Name
10
Location 10
Assigned To 10
Network Configuration DHCP (Enabled)
(N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password Enabled
(N/A)
New Password 10
Confirm 10
Admin Password Enabled
(N/A)
New Password 10
Confirm 10
For more information, please visit http://www.crestron.com.
User Controls 
English   
						

							70
Preparing Email Alerts
1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex-ample, Microsoft Internet 
Explorer v6.01/v8.0). 
2. From the Homepage of LAN/RJ45, click  Alert Settings.
3. By default, these input boxes in Alert Settings are blank. 
4. For Sending alert mail, input the following:
4 The SMTP field is the mail server for sending out email 
(SMTP protocol). This is a required field.
4 The To field is the recipient’s email address (for example,  the projector administrator). This is a required field. 
4 The Cc field sends a carbon copy of the alert to the specified email address. This is an optional field (for 
example, the projector administrator’s assistant). 
User Controls 
English