Optoma Projector Eh1060i User Manual

							English

Appendices
 LED states
 On Screen Messages
		Fan failed: 
  The projector will switch off automatically.
 
	 	Over temperature: 
  The projector will switch off automatically.
 
	 	Replacing the lamp: 
  Lamp is approaching the end of its rated life. 
  Replacement suggested.
	
Remote Control
	If the remote control does not work
	 	
 Check the operating angle of the remote control is within ±15° both 
horizontally and vertically of on of the IR receivers on the projector.
		  Make sure there are no any obstructions between the remote  
control and the projector. Move to within 7 m (23 ft) of the projector.
		Make sure batteries are inserted correctly.
		  Replace batteries if they are exhausted.
Warning: 
Only use genuine 
lamps.       
						

							
Appendices
Replacing the Lamp
The projector automatically detects the lamp life.  When the lamp life is nearing the end of use, you will receive a warning message.
When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
	
Warning: Lamp compartment is hot!  Allow it to cool down before 
changing lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp 
module or touch the lamp bulb. The bulb may shatter and cause 
injury if it is dropped.        
						

							English

Appendices
4
1
2
3       
						

							
Appendices
5
Lamp Replacing Procedure: 
1.    Switch off the power to the projector by pressing the Power button.
2.    Allow the projector to cool down at least 30 minutes. 
3.    Disconnect the power cord.
4.    Open the screw cover.  
5.    Remove the single screw on the lamp compartment cover.  
6.    Remove the lamp compartment cover.  
7.     Remove the three screws from the lamp module.  
Lift the module handle up.  
8.    
Pull firmly on the module handle to remove the lamp module.  


To replace the lamp module, reverse the previous steps. While install -
ing, align the lamp module with the connector and ensure it is level to 
avoid damage.
9.    Turn on the projector and do "Lamp Reset" after the lamp module 
is replaced.
Lamp Reset: (i)Press "Menu" -> (ii)Select "System" -> (iii)Select 
"Lamp Settings" ->(iv)Select "Lamp Reset" -> (v)Select "Yes".       
						

							English

Appendices
Compatibility Modes
Signal ResolutionH-SYNC 
( KHz ) V-SYNC 
( Hz ) COMPOSITE 
S_VIDEO COMPONENT RGB 
(Analog) DVI 
(Digital)
NTSC15.734 60.0 
PAL/SECAM15.625 50.0 
VESA 720 x 400 37.9 85.0

 
640 x 480 31.5 60.0  
640 x 480 37.9 72.8  
640 x 480 37.5 75.0  
640 x 480 43.3 85.0  
800 x 600 35.2 56.3  
800 x 600 37.9 60.3  
800 x 600 46.9 75.0  
800 x 600 48.1 72.2  
800 x 600 53.7 85.1  
1024 x 768 48.4 60.0  
1024 x 768 56.5 70.1  
1024 x 768 60.0 75.0  
1024 x 768 68.7 85.0  
1280 x 800 49.7 59.8  
1280 x 800 62.8 74.9  
1280 x 800 71.6 84.8  
1280 x 1024 64.0 60.0 －
○ 
1280 x 1024 80.0 75.0
 
1280 x 1024 91.1 85.0  
1400 x 1050 65.3 60.0  
1440 x 900 55.9 60.0  
1600 x1200 75.0 60.0  
1920 x 1080 67.2 60.0  
Apple 
Macintosh 640 x 480 35.0 66.7

 
832 x 624 49.7 74.5  
1024 x 768 60.2 74.9  
1152 x 870 68.7 75.1  
SDTV 480i 15.734 60.0

576i 15.625 50.0 
EDTV 576p 31.3 50.0

480p 31.5 60.0 
HDTV 720p 37.5 50.0


720p 45.0 60.0 
1080i 33.8 60.0 
1080i 28.1 50.0 
1080p 67.5 60.0 
1080p 56.3 50.0       
						

							
Appendices
RS232 Commands and Protocol 
Function List
Pin no.Name I/O (From Projector Side)
1 NC __
2 RXD IN
3
TXDOUT
4 NC __
5 NC __
6 NC __
7 RS232 RTS
8 RS232 CTS
9 NC __
RS232 Pin Assignments (projector side)
315
69      
						

							English

Appendices
RS232 Protocol Function List(+56&RPPDQG7DEOH
%DXG5DWH  
DWD%LWV   
3DULW\1RQH  
6WRS%LWV
)ORZ&RQWURO1RQH 
8$57),)2LVDEOH   
3URMHFW R

U5HWXUQ3DVV3
3URMHFWRU5HWXUQ)DLO)  
 ;; SURMHFWRU
V,;; LVIRUDOOSURMHFWRUV

/HDG&RGH3URMHFWRU,&RPPDQG,VSDFHYDULDEOHFDUULDJHUHWXUQ
a ; ; ; ; ;  Q &5
)L[FRGH
2QHLJLW HILQHGE\2SWRPD
RULJLW
6HHWKH)ROORZFRQWHQW 2QHLJLW
3HULWHP
HILQLWLRQ )L[FRGH
2QHLJLW
Function  RS232 Command CodePower on  ~XX00 1 
Power off ~XX00 0 
~XX00 2 
Resync 
~XX01 1 AV Mute on   ~XX02 1 
AV Mute off ~XX02 0 
~XX02 2 
Freeze on  
~XX04 1 
Unfreeze ~XX04 2 
~XX04 0 
IR Function on  
~XX11 1 
IR Function off ~XX11 0 
~XX11 2 
Direct Source Selection 
³HDMI 1 ~XX12 1 HDMI 2 ~XX12 15 VGA ~XX12 5 VGA SCART  ~XX12 7 VGA Component  ~XX12 8 Component ~XX12 14 S-video ~XX12 9 Video ~XX12 10 
Item Key Definition ASCII Pass Fail1  Power  n=1 ~XX140 n  P  F 2  Laser  N/A     3  Remote Mouse Up  n=3 ³
  P  F 4  Remote Mouse Left  n=4  ³
  P  F 5  Remote Mouse Enter  n=5  ³
  P  F 6  Remote Mouse Right  n=6  ³
  P  F 7  Remote Mouse Down  n=7  ³
  P  F 8  Mouse Left Click  n=8 ³
  P  F 9  Mouse Right Click  n=9 ³
  P  F 10  Up/Page +  n=10 ³
  P  F 11  Left/Source  n=11 ³
  P  F 12  Enter (for projection MENU)  n=12  ³
  P  F 13  Right/Re-SYNC  n=13 ³
  P  F 14  Down/Page -  n=14 ³
  P  F 15  Keystone +  n=15 ³
  P  F 16  Keystone -  n=16 ³
  P  F 17  Volume -  n=17 ³
  P  F       
						

							48
Appendices
ItemKey DefinitionASCIIPassFail18 Volume +n=18 
PF19 DVI-D/YPbPr/1 n=19 
PF02=n
2/uneM02  
PF12=n
3/mooZ12  
PFF
P
22=n
4/IMDH2223 Freeze/5 n=23 
PF24 AV Mute/6 n=24 
PF25 S-Video/7 n=25 
PF62=n
8/AGV62  
PF72=n
9/oediV72  
PF
OSD/Image/Display/Setup
Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values\Menu ItemsRS232
Command Code
   Presentation ~XX20 1   Bright ~XX20 2   Movie ~XX20 3   sRGB ~XX20 4   Classroom ~XX20 7Blackboard ~XX20 8User 1 ~XX20 5
Display Mode (1)
User 2 ~XX20 6
Contrast (1)      -50~+50 ~XX22 nBrightness (1)        -50~+50 ~XX21 nColor (1)         -50~+50 ~XX45 nTint (1)   -50~+50 ~XX44 nSharpness (1)   0~15 ~XX23 nNoise Reduction (2)  
 
0 ~ 10 ~XX196 n Curve Type -7~+7 ~XX182 nOffset -5~+5 ~XX183 nReset  ~XX206 1 Film (9a)
Exit NA
Curve Type -7~+7 ~XX184 nOffset -5~+5 ~XX185 nReset  
~XX207 n Video (9a)
Exit NA
Curve Type -7~+7 ~XX186 nOffset -5~+5 ~XX187 nReset  ~XX208 n Graphics (9a)
Exit 
NA
Curve Type -7~+7 ~XX188 nOffset -5~+5 ~XX189 nReset  
~XX209 n 
Gamma (2)
Standard (9a) Exit NA
 
Warm ~XX36 1 Medium ~XX36 2Color Temp. (2) 
 Cold ~XX36 3
Red Gain (2a) -50~+50 ~XX24 nGreen Gain
(2a) -50~+50 ~XX25 n
Blue Gain (2a) -50~+50 ~XX26 nRed Bias (2a) -50~+50 ~XX27 nGreen Bias (2a) -50~+50 ~XX28 n
IMAGEADVANCED (1)
Color Settings (2) Color Settings
Blue Bias (2a) -50~+50 ~XX29 n      
						

							English
49
Appendices
Main Menu  Sub Menu  Sub Menu 2  Sub Menu 3  Sub Menu 4  Values\Menu ItemsRS232  
Command Code
Reset (2a)   ~XX33 1 Exit (2a)   NA ³
  RGB  ~XX3 7  2 ³
  YUV  ~XX3 7  3 Color Space 
³  Auto  ~XX 3 7 1 ³  Normal   ³
  Red   ³  Green   RGB Channel 
³  Blue   
Exit   NA Exit (2)  ³³ ³  NA ³ ³
  4:3  ~XX60  1 ³³
  16:9  ~XX 6 0 2 ³³  LBX  ~XX60  5 Format (1) 
³³  Native  ~ X
 X60 6 Digital Zoom (1)  ³ ³³ ³0~10  ~XX 61 n V Image Shift (1)  ³ ³³ ³-50~+50  ~XX64 n V Keystone (1)  ³ ³³ ³-20~+20  ~XX66 n ³³On ~XX88 1 
DISPLAY  
Closed Captioning  ³³
Off ~XX88 2 
~XX88 0 
³
³  Top Left  ~XX72 1 ³ ³
  Top Right  ~XX72 2 ³ ³
  Center  ~ X X72 3 ³³
  Bottom Left  ~XX72 4 Menu Location (1) 
³³  Bottom Right  ~XX72 5 
Lamp Hours (2)  ³ ³
³ ³ ³ ³
~XX108 1 
³ ³  Off  ~XX109 0 
~XX
109 2 Lamp Reminder (2)
³³  On  ~XX10 9  1 ³³  Bright  ~X X110 1 Brightness Mode (2)
³³
  S
TD  ~XX1 1 0 2 ³³  No  ~XX111  2 Lamp Reset (2) 
³³  Y
ES
  ~
X X
11
1 1 
Lamp Settings (1) 
Exit (2) ³
³ ³
  NA 
³ ³  Front-Desktop  ~XX71 1 ³ ³  Rear-Desktop  ~XX71 2 ³ ³  Front-Ceiling  ~XX71 3 Projection (1) 
³³  Rear-Ceiling  ~XX71 4 
³ ³³  Dark Blue  ~XX104 1 ³ ³
  Grey  ~XX 1 04 3 Background Color 
(1)  ³³  Black  ~X X
 104 2   Default  ~XX82 1 Image 
  User  ~XX 8 2 2 
SYSTEM 
Startup Image  Image Capture      ~XX83 n       
						

							50
Appendices
Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values\Menu ItemsRS232
Command Code
   ECO ~XX114 1Power Mode
(Standby)   Active  ~XX114 2 
~XX114 0 
On 
~XX80 1Mute 
Off ~XX80 2
~XX80 0
Volume
  0~10 ~XX81 nMini  ~XX89 1Audio Input 
RCA 
~XX89 2
Audio Settings
Exit 
 NA 
Projector ID 00~99 
~XX79 nRS232 ~XX86 1RS232
Network ~XX86 2
Network State 
   DHCP    IP Address     ksaMtenbuS     yawetaG     SND    
ylppA   
Network (1)
AN
tixE
    English ~XX70 1    German ~XX70 2    French ~XX70 3    Italian ~XX70 4    Spanish ~XX70 5    
Portuguese ~XX70 6    
Polish ~XX70 7    
Dutch ~XX70 8    
Swedish ~XX70 9    
Norwegian/Danish ~XX70 10    
Finnish ~XX70 11    Greek ~XX70 12    Traditional Chinese ~XX70 13    Simplified Chinese ~XX70 14    Japanese ~XX70 15    Korean ~XX70 16    Russian ~XX70 17    Hungarian ~XX70 18    Czechoslovak ~XX70 19    
Arabic ~XX70 20    
Thai ~XX70 21    
Turkish ~XX70 22
Language (1)
   Exit NA
193XX~
1IMDH793XX~
2IMDH893XX~tnenopmoC593XX~
AGV993XX~
oediv-S0193XX~
oediV
Input Filter (1)
 ExitNA
      
Off~XX100 0 
~XX100 2 
SETUP
Source Lock (1)      On~XX100 1