Optoma Projector Eh1060i User Manual

							English

User Controls
Image
 Display Mode
There are many factory presets optimized for various types of  
images.
 Presentation: Good color and brightness from PC input.
 Brightness: Optimized for maximum brightness.
 Movie: For home theater.
 sRGB: Standardised accurate color.
 Classroom: Recommended settings for classroom.
 Blackboard: Tuned for blackboard usage.
 User 1: User's own settings.
 User 2: User's own settings. 
The initial default settings of this mode is from Presentation 
mode. Any further adjustments by the user in User1/2 will be 
saved in this mode for future use.
  Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. Adjusting the contrast changes 
the amount of black and white in the image.
 Press the	t	to decrease the contrast.
 Press the	u	to increase the contrast.      
						

							
User Controls
 Brightness
Adjust the brightness of the image.
 Press the	t to darken image.
 Press the	u to lighten the image.
  Color
Adjust a video image from black and white to fully saturated color.
 Press the	t to decrease the color saturation in the image.
 Press the	u to increase the color saturation in the image.
  Tint 
Adjust the color balance of red and green.
 Press the	t to increase the amount of green in the image.
 Press the	u to increase the amount of red in the image.
  Sharpness 
Adjust the sharpness of the image.
 Press the	t to decrease the sharpness.
 Press the	u to increase the sharpness.
  Advanced 
Use this option to enter the Advanced menu see page 23.      
						

							English

User Controls
Image | Advanced
 Noise Reduction
The motion Adaptive Noise Reduction reduces the amount of  
visible noise in interlaced signals. The range is from "0" to "10".   
(0=Off)
  Gamma
This allows you to set up gamma curve type. After the initial setup 
and fine tuning is completed, utilize the Gamma Adjustment steps 
to optimize your image output.
	Film: for date projector.
	Video: for video or TV source.
	Graphics: for image source.
	Standard: for standardized setting.
 Color Settings
	
Color Temperature: Adjust the color temperature. Cold  
temperature, the screen looks colder; with Warm temperature, 
the screen looks warmer.
	RGB Gain/Bias: Press	u	into the next menu as below and then 
p or q to select item. Use t or u to select Red, Green, or 
Blue for brightness (Gain) and contrast (Bias).
Color Space: Select an appropriate color matrix type from RGB or YCbCr.
RGB Channel: Select this menu to adjust the RGB Bias and Gain levels for each primary (RGB) color.      
						

							
User Controls
 Format
Use this function to choose your desired aspect ratio.
4:3: This format is for 4x3 input sources.
16:9: This format is for 16x9 input sources, like HDTV and DVD 
enhanced for Widescreen TV.
Letter Box: This format is for non-16x9, letterbox source and for users who use external anamorphic lens to display 2.35:1 
aspect ratio using full resolution. 
Detail informations about Letter Box mode :
1.   Some Letter-Box DVDs are not enhanced for 16x9 TVs. In 
this situation, the image will not look right when displayed in 
16:9 mode. 
In this situation, please try to using the 4:3 mode to view the 
DVD.
If the content is not 4:3, there will be black bars around the 
image in 16:9 display. For this type of content, you can use 
LBX mode to fill the image on the 16:9 display. 
2.   If you use an external anamorphic lens, this LBX mode also 
allows you to watch a 2.35:1 content (include Anamorphic 
DVD and HDTV film source) that support anamorphic wide is 
enhanced for 16x9 Display in a wide 2.35:1 image. 
In this case, there are no black bars. Lamp power and  
vertical resolution are fully utilized.
Display      
						

							English

User Controls
	Native: This format displays the original image without any  
scaling.
 Zoom

Press	t	to reduce the size of the image.
Press	u	to magnify an image on the projected screen.
  V Image Shift
Shift the projected image position vertically. 
 V Keystone
Press the t or u to adjust image distortion vertically and make a 
squarer image.
 Closed Captioning
Select the screen to display closed captioning.
Off-the supplied default setting.
 CC1 I CC2-closed captioning type select. 
Input Signal
Display area
Picture area
Display on Screen      
						

							26
User Controls
	 Menu	Location
Choose	the	menu	location	on	the	display	screen.	
	 Lamp	Settings
Choose	this	menu	to	adjust	your	desired	lamp	setting.
	 Projection
			 Front-Projection
This	is	the	default	selection.	The	image	is	projected	straight	on	
the	screen.
			 Rear-Desktop	
When	selected,	the	image	will	appear	reversed.
			 Front-Ceiling	
When	selected,	the	image	will	turn	upside	down.
			 Rear-Ceiling	
When	selected,	the	image	will	appear	reversed	in	upside	down	
position.
	 Background	Color
Use	this	feature	to	display	a	"Dark	Blue",	"Gray",	or	"Black"	screen	
when	no	signal	is	available.		
	 Startup	Image
Select	the	screen	to	display	during	startup.
System
Rear-Desktop	and	
Rear-Ceiling	are	to	be	
used	with	a	translucent	
screen.
NoteNote      
						

							English

User Controls
 Power Mode (Standby)
Set the projector in ECO Mode or Active Mode.
 Audio Settings
Enter the Audio Settings menu. Set audio level properties.
 Projector ID
Select a two digit projector ID from 0 through 99.
 RS232
Allows RS232 control of an individual projector.
 Network
Allows LAN via web browser (Internet Explore) to control of  
projector. See pages 30 for more information.      
						

							
User Controls
 Lamp Hour
Display the cumulative lamp operating time.
 Lamp Reminder
Choose this function to turn on the lamp reminder. Lamp reminder 
will pop up 30 hours before reaching end of its life.
 Brightness Mode
Choose "Bright" to increase the lamp brightness. Choose "STD" to 
return to normal mode.
 Lamp Reset
Reset the lamp life hour after replacing the lamp.
System |  
Lamp Settings      
						

							English

User Controls
 Image
Select the screen to display during startup.
	Default - the supplied default startup screen.
	User - customized screen capture using the Image Capture 
function.
 Image Capture
Capture a displayed screen to use as the startup screen.
1. Display the desired screen on the projector.
2. Select Image Capture from the Advanced menu.
3. Select OK. Screen capture in progress will display. 
When finished, Screen capture Succeeded will display. 
The captured screen is saved as User in the Image menu.
System |  
Startup Image
Startup Capture  
support in:
HDMI 720p/1080p 
VGA 1920X1080@60Hz
YPbPr 720p/1080p



NoteNote      
						

							0
User Controls
For simplicity and ease of operation, the Optoma projector provides 
diverse networking and remote management features.
The Network function of the projector through a network, such as re-
motely manage:  Power On/Off, Brightness and Contrast settings. Also, 
projector status information, such as: Video-Source, Sound-Mute, etc. 
 
Connect an RJ45 cable to RJ45 ports on the projector and the PC 
(Laptop). 
12V OUT
HDMI 2
HDMI 1
IRL-AUDIO IN-RVGA / SCART / YPbPr
VGA OUT
AUDIO OUT AUDIO IN
RS-232
VIDEO
S-VIDEO
Y
Pb
PrUSB
1.
System |  
Network
Use straight-thru 
cable when  
connecting to a 
hub, switch or a 
router.
Use crossover 
cable for direct 
PC to projector 
connection.


NoteNote