Optoma Hd86 Projector User Manual

English

Introduction
Backup Remote Control
1. Power Off
2. Power On
3. Enter
4.  
Four Directional Select 
Keys
5. Source
6. Menu
1
3
56
2
4
Before using the 
remote control for the 
first time, remove the 
transparent insulation 
tape.
NoteNote
3VOLTSCR2025
Coin Cell Battery Replacement
MnO2-LiCELL3VOLTSJAPANHCR2025
3VOLTSCR2025
M3VOLTSCR2025
12
34
NoteNote
Backup remote  
control is  
magnetically attached 
to the back I/O of the 
projector.      


Installation
Due to the difference 
in applications for each 
country, some regions 
may have different  
accessories.
1.................................................................... VGA Input Cable (Europe Only)
2. ......................................................... DVI/HDMI Cable (Optional Accessory)
3. ........................................................................\
........................... Power Cord
4. .................................................................

English

Installation
Due to the difference in applications for each 
country, some regions 
may have different  
accessories.
1....................... Composite Video Cable (Not Available in European Version)
2. .............................. RCA Component Cable for YPbPr (Optional Accessory)
3. ........................................................................\
... HDMI Cable (Europe Only)
4. ........................................................................\...

14
Installation
Caution 
• Do not shake or place excessive pressure on the  
projector or the lens components as the projector and 
lens components contain precision parts.
• Before removing or installing the lens, be sure to turn off  the projector, wait until the cooling fans stop, and turn 
off the main power switch.
• Do not touch the lens surface when removing or   
installing the lens.
• Keep fingerprints, dust or oil off the lens surface.   Do not scratch the lens surface.
• Work on a level...

English
15
Installation
3. Pull out the existing 
lens slowly.
Installing the New Lens
1. Align the notches and  
correctly position 
the electrical contact 
pad as shown in the 
picture.
2. Rotate the lens  
clockwise until you 
feel it click into place.
Pin of 
IRIS
Pin of IRIS should be in 
the direction as shown 
in the picture.
NoteNote      

16
Installation
Powering On the Projector
1.	 Remove	the	lens	cap.	
2.	 Securely
	connect	the	power	cord	and	signal	cable.	When	
connected,	the	power	led	will	turn	red.
3.	 Turn	on	the	lamp	by	pressing	 “
”	button	on	the	rear	of	
the	projector	or		“
”	on	the	remote	control.		
The	
power	led	“
”	will now flash blue. 	
	 The
	startup	screen	will	display	in	approximately	30	seconds.	
The first time you use the projector, you can select your 
preferred	
 language	from	quick	menu	after	the	startup	screen...

English

Installation
Warning Indicator
▀■ When the “LAMP” indicator led “” is lit orange, the  
projector will automatically shut down. Please call the   
nearest Optoma facility for assistance. 
▀■
  When the “TEMP” indicator “” turns red, it indicates the  
projector has overheated. The projector will shut down   
automatically.  Under normal conditions, the projector can be switched on 
again after it has cooled down.
▀■
  When the “TEMP” indicator “” flashes red, it indicates the 
fan has...


Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
Tilt-Adjustment Feet
The projector is equipped with elevator feet for adjusting 
the image height.
 To raise the image:
Use screw in foot to raise the image to the desired height 
angle and fine-tune the display angle 
. 
 To lower the image:
Use screw in foot to lower the image to the desired height 
angle and fine-tune the display angle 
. 
1      

English
19
Installation
Horizontal Lens 
Shift Lever
Adjusting Projected Image Position 
Using PureShift
The PureShift feature provides a lens shift function that can be 
used to adjust the position of the projected image either  
horizontally or vertically within the range detailed below.   
PureShift is a unique system that provides lens shift while   
maintaining a much higher ANSI contrast ratio than traditional 
lens shift systems.
Vertical Lens 
Shift Lever
▀■ Adjusting the vertical image position...

20
Installation
Screen Height(H)
100%
H x 10% H x 30%
H x 20%
H x 60%
Distance (L)
Screen
▀■	
Adjusting the horizontal image position
With	the	lens	in	the	center	position	the	horizontal	image		
position	can	be	adjusted	to	the	left	or	right	by	up	to	a	maximum	
of	10%	of	the	half	image	width.	Note	that	the	maximum		
horizontal	image	height	adjustment	can	be	limited	by	the		
vertical	image	position.	For	example	it	is	not	possible	to	achieve	
the	maximum	horizontal	image	position	if	the	vertical	image...