Optoma Hd7100 Projector User Manual

N
O I T C U D O R T N )

2EMOTE#ONTROL
0OWER/./&&	BUTTON3UHVVWRWXUQWKHSRZHURQDQGRII
-%.5BUTTON3UHVVWRRSHQWKH

26PHQXV
#OMPONENTBUTTON3UHVVWRFRQQHFWWRFRPSRQHQW
GHYLFHVRXUFHV
!DJUSTMENTBUTTONS
	
3UHVVWRGLVSOD\DGMXVWPHQW
DQGVHWWLQJVFUHHQV
%8)4BUTTON3UHVVWRH[LWWKH26
%.4%2BUTTON3UHVVWRVHWVHOHFWHGLWHPVRU
DGMXVWPHQWVLQWKHPHQX
#OMPONENTBUTTON3UHVVWRFRQQHFWWRFRPSRQHQW
GHY
LFHVRXUFHV...

12
n o i t c u d o r t n I
Using the Remote Control
Available Range of the Remote Control
Theremotecontrolcanbeusedtocontrolthe
projector within the ranges shown in the
illustration.
When using the remote control:
•Do not drop it, or expose it to moisture or high
temperature.
•The remote control may not function correctly
under fluorescent lamps. Operate the projector
away from fluorescent lamps.
Inser ting the Batteries
The batteries (two AA) are included in the package.
Note
•The signal from the remote...

Connections and Setup
13
Connections and Setup 

14
Connections and Setup
Connecting the Projecto r to Other Devices
Before Setting Up
Note
•Before connecting, turn off both the projector andthe devices to be connected. After making all
connections, turn on the projector first and then the other devices.
When connecting a computer, be sure that the comp uter is the last device turned on, after all
connections are made.
•Read the operation manuals of the devices to beconnected before making connections.
This projector can be connected to
Video...

Connections and Setup
15
Connecting to Video Equipment
Using an S-video or a Composite Video
Cable (INPUT 3)
Using an S-video or a composite video cable,
a VCR, laser disc player or other video
equipment can be connected to the INPUT 3
terminals.
Notes
•The INPUT 3 (S-VIDEO) terminal uses a
video signal system in which the picture is
separated into color and luminance signals
to give a higher-quality image. To view the
higher-quality image, use a commercially
available S-video cable to connect the
INPUT...

16
Connections and Setup
Connecting to Component
Video Equipment
Using a Component Cable (INPUT 1 or 2)
Use a component cable when connecting
component video equipment such as DVD
players and DTV* decoders to the INPUT 1 or
2 terminals.
*DTV is an umbrella term used to describe the
new digital television system.
The device’s component jacks may be labeled Y, CB and
CR. Connect each jack as shown below.
Note
•When connecting the projector to video
equipment in this way, set “Input Source” to
“Component 1...

Connections and Setup
17
Connecting Using a DVI-D to 
HDMI Cable
Use a DVI to HDMI cable when connecting 
HDMI video equipment such as DVD players 
to the INPUT 4!terminal.!
1Connect a DVI-D to HDMI cable to 
the projector.
•Secure the connectors by tightening 
the thumbscrews.
2Connect the above cable to the 
video equipment.
 Note
•Select the input signal type of the video 
equipment.
Optional 
accessoryDVI-D to HDMI 
cable
S-V
IDE
O
VI
D
EOPr/C
r
P
b/
Cb
YPr/
Cr
Pb/
CbYPCD
VI
WARN
ING•
Do
n
o
td
is
a...

18
Connections and Setup
Connecting the Projector to a Computer
Connect the projector to the computer 
using an HD 15-pin VGA cable.
•Secure the cable connectors by tightening 
the screws on both sides of the plug.
 Notes
•See page 60 “Computer Compatibility 
Chart” for a list of computer signals 
compatible with the projector. Using 
computer signals other than those listed 
may cause some of the functions not to 
work.
•When connecting the projector to a 
computer using an HD 15-pin VGA cable, 
set the...

Connections and Setup
19
Connecting the Cables
„Connect the cable making sure that it fits correctly into the terminal. 
Secure the connectors by tightening the screws on both sides of the 
plug.
„Do not remove the ferrite cores attached to the cable.
“Plug and Play” Function
„This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC 
compatible computer automatically send settings, allowing for quick and easy setup.
„Before using the “Plug and Play” function, be sure to...

20
Connections and Setup
Using the Adjustment Feet
Use the adjustment feet to level the projector 
when it is placed on an uneven surface or 
when the screen is slanted.
The projection can be made higher by 
adjusting the projector when it is in a location 
lower than the screen.
1Press the foot releases and lift 
the projector to the desired 
angle.
2Remove your hands from the foot 
releases. When the adjustment 
feet have locked in position, 
place the projector down.
•If the screen is at an angle, the...