Optoma Hd180 Projector User Manual

11

English

nstallation
SERVICEVGA/SCART/YPbPrYVIDEO
PbPrHDMI 1HDMI 212V OUT
E62405SPR
MOLEX
 Connecting the Projector
 Connect to Computer/Notebook
1
3
1.........................................................................\
...........................Power Cord2.........................................................................\
...........................*USB Cable3.........................................................................\
..........................*VGA...

12

nstallation

 Connect to Video Sources
1.........................................................................\
...........................Power Cord2.........................................................................\
..........................*VGA Cable 3.........................................................................\
..........*SCART/VGA Adaptor4................................................*15-Pin to 3 RCA Component/HDTV...

13

English

nstallation

Powering On the Projector
1.  Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the ON/STANDBY LED will turn Amber. 
3.  Turn on the lamp by pressing “” button either on the top of 
the projector or on the remote. The ON/STANDBY LED will 
now turn Green. 
  The startup screen will display in approximately 10 seconds. 
The fi rst time you use the projector, you can select your 
preferred language from quick menu after the startup screen...

14

nstallation

Warning Indicator
  When the “LAMP” indicator lights Red (“ON/STANDBY” 
indicator fl ashes Amber), the projector will automatically 
shut down. Please contact your nearest service center for 
assistance.
  When the “TEMP” indicator lights Red (“ON/STANDBY” 
indicator fl ashes Amber), it indicates the projector has 
overheated. The projector will shut down automatically.
  Under normal conditions, the projector can be switched on 
again after it has cooled down.
  When the “TEMP”...

15

English

nstallation

 Adjusting the Projected Image
Adjusting the Projector’s Height 
The projector is equipped with elevator feet for 
adjusting the image height.
1. Locate the adjustable foot you wish to modify on the 
underside of the projector. 
2. Rotate the adjustable ring counter clockwise to raise 
the projector or clockwise to lower it. Repeat with the 
remaining feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring 

16

nstallation
Adjusting the Projector’s Zoom / FocusPOWER
?
Focus Ring
Zoom Ring
You may turn the zoom ring to zoom in or out. To focus the im-
age, rotate the focus ring until the image is clear. 
The projector will focus at distances from 4.89 to 32.68 feet 
(1.49 to 9.96 meters).
Adjusting Projection Image Size
 This table is for user’s reference only.
Diagonallength (inch) size of 16:9 Screen
Screen Size W X H Projection distance (D)Offset(Hd)(m)(feet)(m)(feet)...

17

English

ser ontrols
Using the Control Panel
 PowerRefer to the “Power On/Off the Projector” section on 
pages 13-14.
RE-SYNCAutomatically synchronize the projector to the input 
source.
 EnterConfi rm your item selection.
SOURCEPress “SOURCE” to select an input signal.
MenuPress “Menu” to launch the on-screen display (OSD) 
menu. To exit OSD, Press “Menu” again.
Four Directional 
Select KeysUse     to select items or make adjustments 
to your selection.
Lamp LEDIndicate the projector’s lamp status....

18

ser ontrols

Lamp

Remote Control
Using the Remote Control
Power OnRefer to the “Power On” section on page 13.
Power OffRefer to the “Power On/Off the Projector” section on page 14.
Lamp ModeIncrease the brightness of the image. (refer to page 33)
ModeSelect the display mode from Cinema, 
Bright, Photo, Reference and User.
4:3Scale the image at a 4:3 aspect ratio.
16:9Scale the image at a 16:9 aspect ratio.
LBX
Enable the viewing of the letterboxed 
nonanamorphically enhanced movie at full 
screen...

19

English

ser ontrols

Remote Control
Lamp
Using the Remote Control
EnterConfi rm your item selection.
SourcePress “Source” to select an input signal.
Re-syncAutomatically synchronizes the projector 
to the input source.
MenuDisplay or exit the on-screen display 
menus for projector.
HDMI 1Press “HDMI 1” to choose source from 
HDMI 1 connector.
HDMI 2Press “HDMI 2” to choose source from 
HDMI 2 connector.
D-SubPress “D-Sub” to choose source from 
VGA/SCART/YPbPr connector.
YPbPrPress “YPbPr” to choose...

20

ser ontrols

The Projector has multilingual On-screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “Menu” on the Remote Control or 
Projector Keypad.
2  When OSD is displayed, use   keys to select any item in the 
main menu. While making a selection on a particular page, press 
 or “Enter” key to enter sub menu.
3. Use   keys to select the desired item...