Optoma Ex631 Projector User Manual

EN-31
Video Image
Color
Adjust a video image from black and white to fully saturated color.
Sharpness
Sharpen or soften the image.
Tint
Shift colors toward red or green.
Sound
Vo l u m e
Adjust the volume level.
Mute
Cut off the sound temporarily.
Internal Speaker
Use the internal speaker of projector. 

 EN-32
Setting
Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-
down, in front of or behind the screen. Invert or reverse the image accord-
ingly.
Screen Type (for WXGA model only)
Choose the screen type from16:10 or 16:9.
Color Space
Select an appropriate color matrix type from RGB,YUV.
Lamp Time
Display the lamp’s elapsed operating time (in hours).
Lamp Time Reset
Reset the lamp Hour to 0 hours....

EN-33 Power mode (standby)
Set whether the VGA OUT function works when the projector is in standby
(powered off but connected to AC power).
„ Eco mode: The VGA OUT function will not work when the projector is in 
standby.
„ Active mode: The VGA OUT and AUDIO OUT functions will work when 
the projector is in standby.
Auto Power Off
Set the countdown timer interval. The countdown timer will start, when there
is no signal being sent to the projector. Then projector will automatically
power off when the...

 EN-34devices.
„On: Assign an IP address to the projector from an external DHCP 
server automatically.
„Off: Assign an IP address manually.
„IP Address: Select an IP address.
„Subent mask: Select subnet mask number.
„Gateway: Select the default gateway of the network connected to the 
projector.
„DNS: Select DNS number.
„Apply: Press   and then choose Yes to apply the selection.
Wireless
This setting is only for wireless module use.
Wireless is only functional with VGA 1 connector.
3D Mode
„On: Enable 3D...

EN-35
Language
Select the language used by the on-screen menu.
Factory Default
Restore settings to factory default . 

 EN-36
Use web browser to control your projector
1. Turn on DHCP to allow the DHCP server to automatically assign an IP,
or manually enter the required network information.
2. Then choose apply and press   button to complete the configuration
process.
3. Open your web browser and type in the projectors IP address from the
OSD LAN screen. The following web page will display as below:
•When you used the projector IP address, you will can not link to your service 
server. 

EN-37 4. The crestron control settings can be found in the [tools] tab.(see picture)
Please note, each field can only contain a limited number of characters,
as shown in the table below. (spaces and the other punctuation
included):
CategoryItemInput-Length (characters)
Crestron ControlIP Address 15
IP ID 2
Port 5
ProjectorProjector Name 10
Location 9
Assigned To 9
Network 
ConfigurationDHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User PasswordEnabled (N/A)
New...

 EN-38
Connect you computer to the projector
1. Find an IP Address (10.0.50.100) from LAN function of projector.
2. Select Apply and press Enter button to submit function or press
MENU key to exit.
3. To open Network Connections, click Start, click Control Panel, click
Network and Internet Connections, and then click Network
Connections. Click the connection you want to configure, and then,
under Network Tasks , click Change settings of this connection.
4. On the General tab, under This connection uses...

EN-39 5. Click Use the following IP address, and type in as below:.
„IP address:10.0.50.101
„Subnet mask:255.0.0.0
„Default gateway:10.0.50.254
6. To open Internet Options, click IE web browser, click Internet Options,
click the Connections tab and click LAN Settings.... 

 EN-40 7. The Local Area Network (LAN) Setting dialog box appears, In the Proxy
Server area, cancel the Use a proxy server for your LAN check box.,
then click OK button twice.
8. Open your IE and type in the IP address of 10.0.50.100 in the URL then
press Enter key.
Crestron RoomView Control Tool
Crestron RoomViewTM provides a central monitoring station for 250+ control 
systems on a single Ethernet network (more are possible. the number 
depends on the combination of IP ID and IP address). Crestron...