Olympus Camera Tg 2 Ihs Instruction Manual

							41EN
2 Select the new landmark to be recorded on the 
image using  FG, and press the A button.
3  Select [OK] using FG, and press the A button.
 Rotating images  Rotating images qq [ [yy]]
Submenu 1 Submenu 2
Edit y
1  Use HI to select an image.
2  Press the A button to rotate the image.
3  If necessary, repeat Steps 1 and 2 to make 
settings for other images, and press the   
button.
 
● The new picture orientations will be saved even 
after the power is turned off.
 Erasing images  Erasing images qq [Erase] [Erase]
Submenu 2 Application
All Erase All images in the internal memory 
or card will be erased.
Sel. ImageImages are individually selected 
and erased.
Erase Deletes the image displayed.
Erase Group All images in the group are 
erased.
 
● When erasing pictures in the internal memory, do 
not insert the card into the camera. 
 
● Protected images cannot be erased.
 To individually select and erase images  To individually select and erase images [Sel. Image][Sel. Image]1  Use FG to select [Sel. Image], and press the 
A button.
2  Use FGHI to select the image to be erased, 
and press the A button to add a R mark to the 
image.
 
● Press the T button to the single frame display.
Sel. Image (1)
Erase/CancelOK
MENU
4/304/30
R mark 
						

							42EN
3 Repeat Step 2 to select the images to be erased, 
and then press the  button to erase the 
selected images.
4  Use FG to select [Yes], and press the A 
button.
 
● The images with a  R mark are erased.
 To erase all images [All Erase] To erase all images [All Erase]1 Use FG to select [All Erase], and press the 
A button.
2  Use FG to select [Yes], and press the A 
button.
Saving print settings to the image Saving print settings to the image 
data data qq [Print Order] [Print Order] 
● “Print Reservations” (p. 63)
 
● Print reservation can be set only for still images 
that are recorded to the card.
Protecting images Protecting images qq [ [RR]] 
● Protected images cannot be erased by [Erase] 
(p. 23, 41), [Sel. Image] (p. 41), [Erase Group] (p. 41), 
or [All Erase] (p. 41), but all images are erased by 
[Memory Format]/[Format] (p. 43).
1  Use HI to select an image.
2  Press the A button.
 
● Press the A button again to cancel the 
settings.
3  If necessary, repeat Steps 1 and 2 to protect 
other images, and press the   button.
 
● If you protect the grouped images, all images in the 
group will be protected at once.
Setting images to upload to Setting images to upload to 
Internet using OLYMPUS Viewer 3 Internet using OLYMPUS Viewer 3 
qq [Upload Order] [Upload Order]1  Use HI to select an image.
2  Press the A button.
 
● Press the A button again to cancel the 
settings.
3  If necessary, repeat Steps 1 and 2 to make 
settings for other images, and press the   
button.
 
● Only JPEG fi  les can be ordered.
 
● For details on OLYMPUS Viewer 3, refer to 
“Installing the PC software and registering user” 
(p. 57).
 
● For details on uploading images, refer to 
OLYMPUS Viewer 3 “Help”. 
						

							43EN
Connecting to Smartphone Connecting to Smartphone 
qq [FlashAir] [FlashAir] 
● Using the FlashAir (with Wireless LAN function) 
card (commercially available), you can connect the 
camera to a Wi-Fi enabled smartphone or PC and 
view or import images from the FlashAir card.
 
● When using a FlashAir card, read the FlashAir card 
instruction manual carefully, and comply with the 
instructions.
Submenu 2 Application
Start/Stop Connect to or disconnect from 
Wi-Fi.
Starting option [Manual Start] or [Auto Start] can 
be selected. 
 
● The camera will not go into sleep mode while 
connected to Wi-Fi.
 
● Smartphone application is available. 
http://olympuspen.com/OIShare/
 
● Before use, refer to “FlashAir/Eye-Fi card” (p. 79).
 d Settings Menu 1
 Erasing data completely  Erasing data completely 
dd [Memory Format]/  [Memory Format]/ dd [Format] [Format] 
● Before formatting, check that no important data is 
left in the internal memory or card.
 
● Cards must be formatted with this camera before 
fi rst use or after being used with other cameras or 
computers.
 
● Be sure to remove the card before formatting the 
internal memory.
Submenu 2 Application
Ye s Completely erases the image data 
in the internal memory or card 
(including protected images).
No
Cancels formatting.
 Copying images in the internal  Copying images in the internal 
memory to the card memory to the card dd [Backup] [Backup]
Submenu 2 Application
Ye s Backs up image data in the 
internal memory to the card.
No 
Cancels the backup. 
						

							44EN
Using an Eye-Fi card Using an Eye-Fi card dd [Eye-Fi] [Eye-Fi]
Submenu 2Application
All Transfers all images.
Sel. Image Transfers only selected image.
Off  Disable Eye-Fi communication. 
 
● When using an Eye-Fi card, read the Eye-Fi card 
instruction manual carefully, and comply with the 
instructions.
 
● This camera does not support the Eye-Fi card’s 
Endless mode.
 
● Before use, refer to “FlashAir/Eye-Fi card” (p. 79).
 Saving custom settings Saving custom settings
d d [Custom Mode Setup][Custom Mode Setup]The screen to select the Custom Mode 1 or Custom 
Mode 2 is displayed.
Submenu 2 Application
Set Save current settings.
Reset Return to the default setting.
 Selecting a method for connecting  Selecting a method for connecting 
the camera to other devices the camera to other devices 
dd [USB Connection] [USB Connection]
Submenu 2 Application
Auto Set to select the connection 
method each time the camera is 
connected to another device.
StorageConnect camera as a card reader.
MTP For Windows Vista/Windows 7/
Windows 8, connect camera as a 
portable device.
Print Select when connecting to a 
PictBridge-compatible printer.
 
● When using the supplied software, select [Storage].
 
● Refer to “Connecting with a computer” (p. 56) for the 
connection method with a computer. 
						

							45EN
Turning on the camera with the Turning on the camera with the qq  
button button dd [ [qq Power On] Power On]
Submenu 2Application
No The camera is not turned on. To 
turn on the camera, press the 
n button.
Ye s
Press and hold the 
q button 
to turn the camera on in the 
playback mode.
Selecting the camera sound and Selecting the camera sound and 
its volume its volume dd [Sound Settings] [Sound Settings]
Submenu 2 Submenu 3 Application
Sound Type
1/2/3 Selects the camera 
sounds (operation 
sounds, shutter sound, 
and warning sound).
Volume
0/1/2/3/4/5 Selects the operation 
volume of camera 
buttons.
q Volume
0/1/2/3/4/5 Selects the image 
playback volume.
 d Settings Menu 2
 Resetting the fi
 le names of  Resetting the fi le names of 
pictures pictures dd [File Name] [File Name]
Month: 1 to C
(A=October, 
B=November, 
C=December)
Day: 01 to 31
Pmdd
Folder name Folder name File name
DCIM100OLYMP
999OLYMP Pmdd0001.jpg
Pmdd9999.jpg
Automatic 
numbering
Automatic 
numbering 
						

							46EN
Submenu 2Application
ResetThis resets the sequential number 
for the folder name and 
fi le name 
whenever a new card is inserted.*1 
This is useful when grouping 
images on separate cards.
Auto Even when a new card is inserted, 
this continues the numbering for 
the folder name and 
fi le name 
from the previous card. This is 
useful for managing all image 
folder names and  fi les names with 
sequential numbers.
*1  The number for the folder name is reset to 100,  and the one for the fi  le name is reset to 0001.
Adjusting the image processing Adjusting the image processing 
function function dd [Pixel Mapping] [Pixel Mapping] 
● This function has already been adjusted at factory 
shipping, and no adjustment is needed right 
after purchase. Approximately once a year is 
recommended.
 
● For best results, wait at least one minute after 
taking or viewing pictures before performing pixel 
mapping. If the camera is turned off during pixel 
mapping, be sure to perform it again.
To adjust the image processing functionTo adjust the image processing functionPress the A button when [Start] (Submenu 2) is 
displayed.
 
● The check and adjustment of the image 
processing function starts.
Adjusting the brightness of the Adjusting the brightness of the 
monitor monitor dd [ [ss]]
To adjust the monitor brightnessTo adjust the monitor brightness1  Use FG to adjust the brightness while viewing 
the screen, and then press the  A button.
MENUBacks
Displaying indicators Displaying indicators dd [Info Off] [Info Off]
Submenu 2Application
10secIndicators automatically clear from 
the display if no operations are 
performed for 10 seconds.
Hold Indicators are always displayed 
during shooting.
 
● Indicators that are always displayed may “burn in” 
to the monitor. “Monitor” (p. 99) 
						

							47EN
  Playing back images on a TV   Playing back images on a TV dd [TV Out] [TV Out]
  The TV video signal system varies depending on the countries and regions. Be\
fore viewing camera images on your TV, select the video output according to your TV’s video signal type.
Submenu 2 Submenu 3 Application
NTSC/PAL NTSC
Connecting the camera to a TV in North America, Taiwan, Korea, 
Japan, and so on.
PA L Connecting the camera to a TV in European countries, China, and 
so on.
HDMI Out
480p/576p
720p
1080i Set the signal format to be given priority. If the TV setting does not 
match, it is changed automatically.
HDMI Control
Off Operate with the camera.
On Operate with the TV remote control.
  The factory default settings differ according to the region where the camera is sold.
To play back camera images on a TVTo play back camera images on a TV 
● Connection via AV cable
1  Use the camera to select the same video signal system as the one of conn\
ected TV ([NTSC]/[PAL]).
2  Connect the TV and camera.
 
●  Connection via HDMI cable
1  On the camera, select the digital signal format that will be connected (\
[480p/576p]/[720p]/[1080i]).
2  Connect the TV and camera.
3  Turn on the TV, and change “INPUT” to “VIDEO (an input jack connected to the\
 camera)”.
4  Turn on the camera, and use  FGHI to select the image for playback.
 
● When the camera is connected to the computer by the USB cable, do not co\
nnect the HDMI cable to the 
camera. 
						

							48EN
Connect to the TV video 
input jack (yellow) and 
audio input jack (white).Connect to the HDMI 
connector on the TV.
HDMI micro connector 
(type D) HDMI cable 
(sold separately: CB-HD1) AV cable 
(sold separately: CB-AVC3)
Multi-connector
 
● For details on changing the input source of the TV, refer to the TV’s instruction manual.
 
● When the camera and TV are connected by both an AV cable and an HDMI cable, the HDMI cable will take 
priority.
 
● Depending on the TV’s settings, the displayed images and information may become cropped.
To operate images with the TV remote controlTo operate images with the TV remote control1  Set [HDMI Control] to [On], and turn off the camera.
2  Connect the camera and TV with an HDMI cable. “Connection via HDMI cable” (p. 47)
3  First turn on the TV, and then turn on the camera.
 
● Operate by following the operation guide that is displayed on the TV.
 
● With some TVs, operations cannot be performed with the TV remote control even though the operation guide 
is displayed on the screen.
 
● If operations cannot be performed with the TV remote control, set [HDMI Control] to [Off] and operate using 
the camera. 
						

							49EN
 Saving battery power between  Saving battery power between 
shots shots dd [Power Save] [Power Save]
Submenu 2Application
OffCancels [Power Save].
On When the camera is not being 
used for approx. 10 seconds, the 
monitor automatically turns off to 
save battery power.
To resume standby modeTo resume standby modePress any button.
 Changing the display language  Changing the display language dd  
[[ll]]
Submenu 2
Application
Languages The language for the menus and 
error messages displayed on the 
monitor is selected.
 d Settings Menu 3
 Setting the date and time  Setting the date and time dd [ [XX]]1 
Press FG of the arrow pad to select the year 
for [Y].
2  Press I of the arrow pad to save the setting 
for [Y].
3  As in Steps 1 and 2, press FGHI of the 
arrow pad to set [M] (month), [D] (day), [Time] 
(hours and minutes), and [Y/M/D] (date order), 
and then press the A button.
 
● For precise time setting, press the A button as the 
time signal strikes 00 seconds.
To check the date and timeTo check the date and timePress the INFO button while the camera is turned off. 
The current time is displayed for approx. 30 seconds. 
						

							50EN
 Choosing home and alternate time  Choosing home and alternate time 
zones zones dd [World Time] [World Time] 
● You will not be able to select a time zone using 
[World Time] if the camera clock has not fi  rst been 
set using [X].
Submenu 2 Submenu 3 Application
Home/
Alternate x
The time in the home 
time zone (the time 
zone selected for 
x in 
submenu 2).
z The time in the travel 
destination time zone 
(the time zone selected 
for z in submenu 2).
x
*1— Select the home time 
zone (x).
z
*1, 2— Select the travel 
destination time zone 
(z).
*1  In areas where daylight saving time is in effect, use 
FG to turn daylight saving time ([Summer]) on.
*2  When you select a time zone, the camera automatically calculates the time difference 
between the selected zone and the home 
time zone (x) to display the time in the travel 
destination time zone ( z).
 Registering the settings for Beauty  Registering the settings for Beauty 
Fix Fix dd [Beauty Settings] [Beauty Settings] 
● Depending on the picture, the editing may not be 
effective.
1  Use FG to select a retouching setting, and 
press the Q button.
2  Press the shutter button to take a portrait picture.
Take a portrait picture.
 
● The image is not saved.
3  Select a retouching item and retouching level, and 
press the A button.
MENU
Off
Eye Color Back
4 Press the Q button on the review screen to save 
the image.
 
● Registration is complete.