OKI C9600HDN User Manual

C9600 User’s Guide> 61
7.Turn on the printer.
CLEANING THE PRINTER CASING
1.Follow the correct steps to turn the printer off.
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 62
2.Wipe the printer surface with a soft cloth moistened 
sparingly with water or neutral detergent.
3.Use a soft dry cloth to dry the printer surface.
4.Turn on the printer.
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 63
EMPTYING THE PUNCH CHIP BOX (PUNCH UNIT OPTIONAL 
ACCESSORY)
When the LCD panel indicates that the punch chip box is full, 
empty the box as follows:
1.Operate the Finisher lever and move the Finisher away 
from the printer.
2.Pull out the punch chip box, being careful to keep it level 
so as not to spill any chips.
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 64
3.Discard the chips in an appropriate place.
4.Refit the punch chip box carefully into the Finisher.
5.Check that the punch chip box has been refitted correctly 
then move the Finisher back into position, being careful 
not to trap your fingers.
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 65
OPTIONAL ACCESSORIES
This section describes optional accessory equipment for your 
printer. The following accessories are available:
>duplex unit (to enable two-sided printing) (C9600n only)
>additional RAM memory
>hard disk drive (required for verified and spooled printing, 
direct printing of PDFs, when collation errors appear, 
adding extra fonts) (C9600n and C9600dn only)
>second, third paper tray (to increase paper input capacity)
>high capacity feeder (equivalent to three...

C9600 User’s Guide> 66
ACCESSORY ORDER INFORMATION
ITEMORDER NUMBER
Duplex unit 42797203
Additional RAM memory
128 MB
256 MB
512 MB01163401
01163402
01163403
Hard disk drive 01163601
Second, third paper tray 42831303
High capacity feeder (HCF) 42831503
Wireless LAN card 01163201
Finisher:
4-tray
5-tray01166701
01166801
Finisher Punch Unit:
4 hole
2 hole
4 hole (Sweden)42872903
42872901
42872904
Cabinet (same height as HCF) TBD
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 67
INSTALLING ACCESSORIES
Each accessory (apart from the Finisher) comes complete with its 
own documentation which gives full instructions on installation. 
You are advised to follow these instructions carefully.
After installation, print out a Menu Map (Configuration document) 
to check that the installation has been successful.
NOTE
The Finisher and Punch unit must be installed by an authorised 
engineer.
For the following accessories, you have to make the appropriate 
setting in...

C9600 User’s Guide> 68
TROUBLESHOOTING
GENERAL
If the printer display panel does not display anything or is still in 
standby mode 10 minutes after switching on, follow the printer 
shutdown sequence to switch it off. Check all cable connections 
before restarting the printer. If the problem persists, contact 
your dealer.
PAPER JAMS
This section provides information to help you deal with problems 
that may arise when using the printer. The following paragraphs 
describe actions to take in the event of a...

C9600 User’s Guide> 69
OPEN COVER, PAPER JAM, TTTTTT SIDE COVER
Tray 1, or any one of Tray 2 to Tray 5 (if installed), can appear 
in place of the tttttt characters in the LCD panel message. In this 
example Tray 1 is used, the procedure being similar for all other 
trays.
1.Squeeze the catch (1) on Tray 1 side cover and open the 
cover.
2.Carefully remove the jammed paper.
1
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 70
3.Close Tray 1 side cover.
OPEN COVER, PAPER JAM, SIDE COVER
1.If the MP Tray is open, close it so that the side cover (1) is 
visible.
1
Downloaded From ManualsPrinter.com Manuals