OKI C8600cdtn User Manual

							
Menu functions> 71
TRAY1 
MEDIAWEIGHT
LIGHT (64~74g/
m²)
MEDIUM 
(75~90g/m²)
HEAVY (91~
120g/m²) Adjusts the printer for the weight of 
paper stock loaded in this tray.
TRAY1 LEGAL
SIZELEGAL 14
LEGAL 13.5
LEGAL 13Specifies the legal pa
per size for TRAY1.
TRAY2 PAPERSIZE CASSETTE SIZE 
CUSTOM Selects the size of paper loaded in Tray 2 
(lower) if installed. For CUSTOM setting 
see X-DIMENSION and Y-DIMENSION 
later in this table.
TRAY2 PAPER 
WIDTH 100mm
210mm
297mmSets the width of a custom paper for 
TRAY2 (lower) if installed. That is, the 
dimension at 
right angles to the direction 
of paper feed.
TRAY2 PAPER 
LENGTH 148mm
297mm
420mm Sets the length of a custom paper for 
TRAY2 (lower). That is, the dimension
 in 
the direction  of  paper feed.
TRAY2 MEDIATYPEPLAIN
LETTERHEAD
TRANSPARENCY
BOND
RECYCLED
ROUGH
SPECIAL
USER TYPE 1
USER TYPE 2
USER TYPE 3
USER TYPE 4
USER TYPE 5Selects the type of media loaded in this 
tray (if installed). (see notes above for 
tray 1).
TRAY2 
MEDIAWEIGHT LIGHT (64~
74g/m²)
MEDIUM 
(75~90g/m²)
HEAVY (91~
120g/m²) Adjusts the printer for the weight of 
paper stock loaded in this tray (if 
installed).
TRAY2 LEGAL
SIZELEGAL 14
LEGAL 13.5
LEGAL 13Specifies the legal pa
per size for TRAY2.
(Displayed if an optional second tray unit 
is installed).
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
Menu functions> 72
MPT PAPERSIZE A3
A4 SEF
A4 LEF
A5 SEF
A6
B4
B5 SEF
B5 LEF
LEGAL 14
LEGAL 13.5
LEGAL 13
LETTER SEF
LETTER LEF
EXECUTIVE
CUSTOM
COM-10
ENVELOPE
DL ENVELOPE
C5 ENVELOPE
C4 ENVELOPE Selects the size of paper to be fed from 
the multi purpose tray. For CUSTOM 
setting see X-DIMENSION and Y-
DIMENSION later in this table.
MP TRAY PAPER 
WIDTH64mm
210mm
297Sets the width of a custom paper for the 
MP tray. That is, the dimension at 
right 
angles  to the direction of paper feed.
MP TRAY PAPER 
LENGTH 105mm
297mm
1200mm Sets the length of a custom paper for the 
MP tray. That is, the dimension
 in the 
direction  of  paper feed.
MPT MEDIATYPEPLAIN
LETTERHEAD
TRANSPARENCY
BOND
RECYCLED
ROUGH
SPECIAL
USER TYPE 1
USER TYPE 2
USER TYPE 3
USER TYPE 4
USER TYPE 5Selects the type of media to be fed from 
the multi purpose tray so that the printer 
can adjust its internal parameters to 
better accommodate the selected type of 
media.
MPT 
MEDIAWEIGHT LIGHT (64~
74g/m
²)MEDIUM (75-
90g/m²)
HEAVY (91-
120g/m²)
ULTRA HEAVY 
(121-203g/m²) Selects the media weight to be fed from 
the multi purpose tray.
UNIT OF MEASUREMILLIMETRE
INCHSelects the unit of measure for the next 
two items.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
Menu functions> 73
COLOUR MENU
The printer automatically adjusts colour balance and density at 
appropriate intervals, optimising the printed output for bright 
white paper viewed in natural daylight conditions. The items on 
this menu provide a means of changing the default settings for 
special or particularly difficult print jobs. Settings revert to their 
default values when the next print job is complete.
ITEMSETTINGSEXPLANATION
ADJUST DENSITY EXECUTE Image density will be automatically 
adjusted at power on, when a new image 
drum or toner cartridge is installed, and at 
intervals of 100, 300 and 500 drum 
counts. If a 500 drum count interval 
occurs during a print job it will occur at 
the end of that job, and will take up to 55 
seconds.
DENSITY 
CONTROLAUTO
MANUALSelecting this will permit automatic 
adjustment of the colour density.
AUTO COLOR 
REGISTRATION EXECUTE Performs automatic colour registration 
adjustment. Normally this is done on 
power on and when the top cover is 
opened and then closed. This process 
accurately aligns the cyan, magenta and 
yellow images to the black image.
C REG FINE ADJ
M REG FINE ADJ
Y REG FINE ADJ-3~0~+3
-3~ 0~+3
-3~ 0~+3Performs fine adjustment of image timing 
in relation to the black image component.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 74
SYSTEM CONFIGURATION MENU
This menu adjusts general printer settings to suit the way you 
prefer to work.
ITEMSSETTINGSEXPLANATION
POWER SAVE 
DELAY TIME5
15
30
60
240Adjusts the idling time before the printer 
automatically switches into power saving 
mode. In this mode power consumption is 
reduced to a low level required to just 
keep the printer operating and ready to 
receive data. When a job is sent the 
printer will require a warm-up time of up 
to 1 minute before printing can begin.
CLEARABLE 
WARNINGONLINE
JOBWhen ONLINE, non-critical warnings, such 
as requests for a different paper size, can 
be cleared by pressing the 
ON LINE 
button. When set to JOB, they are cleared 
when the print job resumes.
MANUAL TIMEOUT OFF
30
60Specifies how many seconds the printer 
will wait for paper to be fed before 
cancelling the job.
WAIT TIMEOUT5~90~300Specifies how many seconds the printer 
will wait when received data pauses 
before forcing a page eject. In PostScript 
Emulation mode the job will be cancelled 
if timeout occurs.
TONER LOW 
CONTINUE 
PRINTINGCONTINUE
STOPSpecifies whether the printer should 
continue printing even after a low toner 
condition is detected.
JAM RECOVERYON
OFFSpecifies whether the printer should 
perform jam recovery after a paper jam 
has occurred. If ON, the printer will 
attempt to print again any pages lost due 
to a paper jam once the jam has been 
cleared.
ERROR REPORT ON
OFFSets whether an error report is printed 
when an internal fault occurs.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 75
USB MENU
This menu controls the operation of the printer’s USB data 
interface.
NETWORK MENU
This menu controls the operation of the printer’s 10Base-T/
100Base-TX network interface.
ITEMSETTINGSEXPLANATION
SOFT RESET ENABLE / 
DISABLEEnables or disables the SOFT RESET 
command.
SERIAL NUMBERENABLE / 
DISABLESpecifies whether to ENABLE or DISABLE 
a USB serial number.
The USB serial number is used to identify 
the USB device connected to your PC.
SPEED 12 / 480 Mps Selects the interface speed
NOTE:
When you have changed any settings in the USB MENU, turn 
the printer OFF, then ON again.
ITEMSETTINGSEXPLANATION
TCP/IPENABLE / 
DISABLEEnables or disables this network protocol.
NETBEUIENABLE / 
DISABLEEnables or disables this network protocol.
IP ADDRESS SETAUTO / MANUAL Specifies whether IP address allocation is 
automatic (DHCP) or manually assigned.
IP ADDRESSxxx.xxx.xxx.xxxCurrent assigned IP address. To change, 
press ENTER and use +/– buttons to 
increment 1st octet, then press ENTER 
again to move on to next octet. When 4th 
octet has been set, press ENTER again to 
register new address.
SUBNET MASK xxx.xxx.xxx.xxx Current assigned subnet mask. To 
change, proceed as above.
GATEWAY 
ADDRESSxxx.xxx.xxx.xxxCurrent assigned gateway address. To 
change, proceed as above.
FACTORY 
DEFAULTSEXECUTE Reloads the settings present when the 
unit was setup by the manufacturer.
WEBENABLE / 
DISABLEEnables or disables Web config. facility.
TELNET ENABLE / 
DISABLEEnables or disables Telnet config. facility.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 76
MEMORY MENU
SYSTEM ADJUST MENU
FTPENABLE / 
DISABLEEnables or disables communication via 
FTP.
SNMPENABLE / 
DISABLEEnables or disables SNMP protocol.
NETWORK SCALENORMAL / SMALLSelects network size.
HUB LINK 
SETTINGAUTO 
NEGOTIATE
100BASE-TX FULL
100BASE-TX HALF
10BASE-T FULL
10BASE-T HALFSets full or half duplex for communication 
via a network hub.
ITEMSETTINGSEXPLANATION
ITEMSETTINGSEXPLANATION
RECEIVE BUFFER 
SIZEAUTO
0.5 MB
1 MB
2 MB
4 MB
8 MB
16 MB
32 MBSets the receive buffer size.
The setting depends on the amount of 
memory installed
ITEMSETTINGSEXPLANATION
X ADJUST  0.00 MM
+0.25 MM
+2.00 MM
-2.00 MM
-0.25 MMHorizontally adjusts the print position of 
the entire image at 0.25 mm pitch.
Any image that lies outside the printable 
area is not printed.
Y ADJUST 0.00 MM
+0.25 MM
+2.00 MM
-2.00 MM
-0.25 MMVertically adjusts the print position of 
the whole image at 0.25 mm pitch.
Any image that lies outside the printable 
area is not printed.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 77 DUPLEX X
ADJUST0.00 MM
+0.25 MM
+2.00 MM
-2.00 MM
-0.25 MMIn duplex printing, horizontally adjusts 
the print position of the entire image on 
the rear surface at 0.25 mm pitch.
Any image that lies outside the printable 
area is not printed.
DUPLEX Y
ADJUST0.00 MM
+0.25 MM
+2.00 MM
-2.00 MM
-0.25 MMIn duplex printing, vertically adjusts the 
print position of the entire image on the 
rear surface at 0.25 mm pitch.
Any image that lies outside the printable 
area is not printed.
With PS, adjustment in a negative 
direction is disabled.
DRUM
CLEANINGON
OFFPerforms a cleaning action of the image 
drum before printing. This can be 
effective in improving the image.
NOTE:
In the factory default settings, the MEMORY MENU and SYS 
ADJUST MENU are not displayed in the user menu. They will 
be displayed in the user menu when the “MEMORY MENU” and 
“SYS ADJUST MENU” settings are changed to [ENABLE] in the 
administrator menu. For details, refer to “How to change the 
settings - Administrator” on page 68.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 78
MAINTENANCE MENU
This menu provides access to various printer maintenance 
functions.
ITEMSETTINGSEXPLANATION
MENU RESET EXECUTE Resets menus to default settings.
SAVE MENUEXECUTESaves the current menu settings. The last 
menu executed is saved and the menu 
previously saved is overwritten and 
erased.
When you press the ENTER button, the 
following confirmation message is 
displayed.
“DO YOU WANT TO EXECUTE THIS 
FUNCTION?” YES/NO
If you select NO, the display returns to 
the previous menu.
If you select YES, the current menu 
settings are stored and the menu is 
exited.
RESTORE MENU EXECUTE Restores the saved menu settings.
When you press the ENTER button, the 
following confirmation message is 
displayed.
“DO YOU WANT TO EXECUTE THIS 
FUNCTION? YES/NO”
If you select NO, the display returns to 
the previous menu. 
If you select YES, the stored menu 
settings are restored and the menu is 
exited.
*This function cannot be executed when 
print data is in the memory.
POWER SAVE 
FUNCTIONENABLE / 
DISABLEEnables or disables automatic power save 
mode.Delay before entering this mode is 
set in the SYSTEM CONFIGURATION 
menu.
PAPER BLACK 
SETTING–2~0~+2 Used for small adjustment when you 
experience faded print or light specks / 
streaking in monochrome printing on 
white paper. Select a higher value to 
reduce fading, or a lower value to reduce 
specks or streaking in high density print 
areas.
PAPER COLOR 
SETTING–2~0~+2As above, but for colour printing.
SMR SETTING –3~0~+3 Compensates for print variations caused 
by differences in temperature, humidity, 
and printing density/frequency.
Change the value when the image quality 
is uneven. 
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 79
USAGE MENU
This menu is for information only, and provides an indication of 
total usage of the printer and the expected life left in its 
consumable items. This is particularly useful if you do not have a 
full set of replacement consumables to hand and you need to 
know how soon you will need them.
BG SETTING–3~0~+3Compensates for print variations caused 
by differences in temperature, humidity 
and printing density/frequency.
Change the value when the background 
density is high.
TRANSPR BLACK 
SETTING–2~0~+2 As above but for mono printing on 
transparencies.
TRANSPR COLOR 
SETTING–2~0~+2As above but for colour printing on 
transparencies.
ITEMSETTINGSEXPLANATION
ITEMEXPLANATION
TOTAL TRAY COUNT The total number of pages printed.
TRAY1 PAGE COUNTThe total number of pages fed from tray 1.
TRAY2 PAGE COUNT The total number of pages fed from tray 2.
MPT PAGE COUNTThe total number of pages fed from the multi purpose 
tray.
COLOR PAGE COUNT The total number of pages printed in colour.
MONO PAGE COUNTThe total number of pages printed in monochrome.
K DRUM LIFE 
REMAINING
C DRUM LIFE 
REMAINING
M DRUM LIFE 
REMAINING
Y DRUM LIFE 
REMAININGPercentage of life remaining in these consumable items.
BELT LIFE REMAININGPercentage of belt life remaining.
FUSER LIFE REMAINING Percentage of fuser life remaining.
K TONER
C TONER
M TONER
Y TONERCartridge size and current toner level.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing consumable items> 80
REPLACING CONSUMABLE ITEMS
This section explains how to replace consumable items when due. 
As a guide, the life expectancy of these items is:
>Toner:
The printer is shipped with sufficient Cyan, Magenta, 
Yellow & Black toner for 6,000 A4 pages in the print 
cartridges.
>Image drum: Approximately 20,000 A4 pages (calculated 
on typical office usage where 20% of printing is 1 page 
only, 30% is 3 page documents and 50% is print runs of 
15 pages or more).
>Transfer belt: Approximately 80,000 A4 pages.
>Fuser: Approximately 100,000 A4 pages.
A4 PAGE COVERAGE 
(OF THIS COLOUR)2.5%5.0%10%
Black 12,000 6,000 3,000
Cyan12,0006,0003,000
Magenta 12,000 6,000 3,000
Ye l l o w12,0006,0003,000
Downloaded From ManualsPrinter.com Manuals