OKI C710cdtn User Manual

							51 – C710n User’s Guide
Cyan/
Magenta/
Yellow/Black 
TuningHighlight-3,-2,-
1, 
0,+1,+
2,+3, Adjusts HIGHLIGHT (light area) 
of the TRC.
+ = Darker 
- = Lighter
Mid-Tone-3,-2,-
1, 
0,+1,+
2,+3, Adjusts MID-TONE area of the 
TRC.
+ = Darker 
- = Lighter
Dark-3,-2,-
1, 
0,+1,+
2,+3, Adjusts DARK area of the TRC.
+ = Darker 
- = Lighter
Cyan/
Magenta/
Yellow/Black 
Darkness-3,-2,-
1, 
0,+1,+
2,+3, Adjusts the engine density.
The Darkness settings for each 
of CMYK will be reflected as 
offset values (addition) to the 
corrections through the Adjust 
Density/TRC Compensation 
function.
ITEMSETTI
NGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							52 – C710n User’s Guide
Print Statistics
ITEMSETTINGSEXPLANATION
Enter PasswordXXXXEnters a password to enter Print 
Statistics menu.
The default value is 0000.
The password for entry to Print 
Statistics is different from the 
password for entry to Functions-
Admin Setup.
Print Statistics category is not 
shown when Print Statistics function is 
not supported.
Section 
Counter
Enable/
DisableSpecifies if the section counter is 
displayed in Usage Report Print or 
not.
Enable: Displayed
Disable: Not displayed.
Enable must be selected in Functions/
Print Statistics/Usage Report
Reset Group 
Counter
ExecuteResets the main counter to zero.
When executing this menu, resets the 
main counter to zero and exits from 
the menu.
Enable must be selected in Functions/
Print Statistics/Usage Report.
Group CounterEnable/
DisableSpecifies if the Group counter is 
displayed in the Usage Report Print.
Enable: Displayed,
Disable: Not displayed.
Conditions for display:
Enable must be selected in Functions/
Print Statistics/Usage Report.
Usage ReportEnable/
Disable
Enables/Disables the printing of the 
Usage Report.
When changing a setting value, the 
printer is rebooted.
Change 
Password
Changes the password.
Enable must be selected in Functions/
Print Statistics/Usage Report
Downloaded From ManualsPrinter.com Manuals 
						

							53 – C710n User’s Guide
Administrator (Boot) Menu
This menu is only accessible to System Administrators. In order to gain access 
to this menu, follow the instructions in “How to Change the Settings: 
Administrator” on page 24.
This menu is in English only (default settings in bold type).
Parallel Setup
This menu controls the operation of the printer’s Parallel data 
interface.
New 
Password
xxxxSets a new password to enter Print 
Statistics menu.
Ver ify 
Password
xxxxRe-enter new password set to enter 
Print Statistics set in New Password 
for confirmation.
ITEMSETTINGSEXPLANATION
Enter 
Passwordxxxxxxxxxxxx Enter a password to gain entry to the 
Admin menu.
Password should be from 6 to 12 digits of 
alpha/numeric characters (or mix) 
The default value is aaaaaa
The printer will restart after the Boot 
Menu.
ParallelEnable / 
DisableEnables or disables the parallel port.
Bi-directionEnable / 
DisableENABLE/DISABLE the bi-directional 
capability of the parallel interface.
EcpEnable / 
DisableExtended Capabilities Port, enables/
disables this function.
Ack Width
Narrow/
Medium/
WideSets ACK width for compatible reception.
= 0.5µs
= 1.0µs
= 3.0µs
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							54 – C710n User’s Guide
USB Setup
This menu controls the operation of the printer’s USB data 
interface.
When you have changed any settings in the USB MENU, turn the 
printer OFF, then ON again.
Ack / Busy 
TimingAck In Busy 
/  
Ack While 
BusySets the order to output the BUSY and 
ACK signal for compatible reception.
I-primeDisable/
3µsec/50µsecSets time to enable/disable I-prime signal
Offline 
ReceiveEnable / 
DisableTo Enable/disable of this function. When 
set to Enable, the interface retains a 
receive possible state even when switching 
to Offline. Interface sends the BUSY signal 
only when the receive buffer is full or a 
service call occurs.
ITEMSETTINGSEXPLANATION
UsbEnable / 
DisableENABLES / DISABLES the USB port.
Speed 12 / 480 
MbpsSelects the interface speed. After setting 
change the menu, the
printer restarts on exit.
Soft 
ResetEnable / 
DisableEnables or disables the SOFT RESET command.
Offline 
ReceiveEnable / 
DisableOFFLINE RECEIVE.
Serial 
NumberEnable / 
DisableSpecifies whether to ENABLE or DISABLE a USB 
serial number.
The USB serial number is used to identify the 
USB device connected to your PC.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							55 – C710n User’s Guide
Security Setup
Only available when a Hard Disk (option) is fitted.
Storage System
Only available when a Hard Disk (option) is fitted.
ITEMSETTINGSEXPLANATION
Job 
LimitationsOff
Encrypted
JobJob limitation mode control.
Jobs other than specified ones are 
rejected.
Reset 
Cipher KeyExecute Resets a cipher key to be used on an 
encrypted hard disk.
When this processing is done, all data 
stored on the hard disk cannot be 
restored.
After execution, the following confirmation 
messages will appear.
Are You Sure?  es / No
No - display returns to the previous 
menu.
Yes =, the printer automatically reboots 
and the cipher key reset is executed.
ITEMSETTINGSEXPLANATION
Check File 
SystemExecute Resolves mismatch between actual memory 
and displayed memory available in a file 
system. Performs administration data (FAT 
information) recovery. Performs recovery 
only for an HDD.
Check All 
SectorsExecute Performs recovery of defective HDD sector 
information and a file system mismatch 
mentioned above. The target device is only a 
HDD and it takes 30 to 40 minutes to 
complete this function for an HDD of 10GB.
Downloaded From ManualsPrinter.com Manuals 
						

							56 – C710n User’s Guide
Enable HDD Yes
NoEven if a machine is inoperable at 
installation because of a faulty HDD, the 
machine can be made operable by setting 
this parameter to No (ignores the existence 
of the HDD).
When No is set, access to a HDD results in 
FAIL because the HDD is regarded as not 
attached.
After setting change and exit from the 
menu, the printer will restart.
Erase HDD Execute Deletion of all data stored in the hard disk. 
DoD 5220.22-M sanitizing formula is used 
for clearing the desk. The machine will 
restart after changing setup. The following 
message appears after pressing the Enter 
switch.
Are You Sure?  Yes / No
NO = return to the source menu
Yes = the procedure for clearing disk stars 
immediately after the machine reboots.
If the Cancel button is held down during 
erasing, the following confirmation 
messages will appear to discontinue 
processing.
Do You Wish to Cancel?  Yes / No
NO= procedure will continue.
YES = procedure will discontinue. 
Enable 
initializatio
nNo
Ye sPrevents a setting change accompanying 
initialization of Block Device (HDD,FLASH).
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							57 – C710n User’s Guide
Power Setup
Language Setup
ITEMSETTINGSEXPLANATION
Power SaveEnable
Disable
Sets Enable/Disable of Power Save Mode.
ITEMSETTINGSEXPLANATION
Language 
initializeExecuteInitializes the message file loaded in FLASH.
When you press the Enter button, the 
following message, requesting confirmation, 
will appear, 
Are You Sure?  Yes / No
NO = return to the source menu.
The procedure for clearing the disk will start 
immediately after the menu and rebooting.
Downloaded From ManualsPrinter.com Manuals 
						

							58 – C710n User’s Guide
Available Options
See the instructions supplied with the options.
Duplex (two-sided printing) Unit ___
Oki P/N 43830005
The duplex unit adds the function of two-sided printing, using less 
paper and making large documents easier to handle. It also 
enables booklet printing, which uses even less paper and makes 
large documents even easier to handle.
The duplex unit slides straight into the rear of the printer and 
requires no tools to install.
Additional RAM Memory __________
Oki P/N 43363304 (256 MB), 43363305  (512 MB)
The basic printer model comes equipped with 256MB of main 
memory. This can be upgraded with an additional memory board 
of 256MB or 512MB, giving a maximum total memory capacity of 
768MB.
Installation takes a few minutes, and requires a medium size 
cross-head (philips type) screwdriver.
Downloaded From ManualsPrinter.com Manuals 
						

							59 – C710n User’s Guide
Hard Disk Drive _________________
Oki P/N 41376046
The optional internal hard disk drive (HDD) enables collating of 
printed pages and can be used to store overlays and macros, fonts, 
and secure or proof documents waiting to be printed.
Installation takes a few minutes, and requires a medium size 
cross-head (philips type) screwdriver.
Additional Paper Tray(s) __________
Oki P/N 3855101 
The paper trays hold 530 sheets of 20-lb. US Bond (75 g/m2) 
paper and require no tools to install
Downloaded From ManualsPrinter.com Manuals 
						

							60 – C710n User’s Guide
Clearing Paper Jams
Provided that you follow the recommendations in this guide on the 
use of print media, and you keep the media in good condition prior 
to use, your printer should give years of reliable service. However, 
paper jams occasionally do occur, and this section explains how to 
clear them quickly and simply.
Jams can occur due to paper misfeeding from a paper tray or at 
any point on the paper path. When a jam occurs, the printer 
immediately stops, and the Status Panel (together with the Status 
Monitor) informs you. If printing multiple pages (or copies), do not 
assume that, having cleared an obvious sheet, others will not also 
be stopped somewhere along the path. These must also be 
removed in order to restore normal operation.
Major Printer Components and Paper Path 
1. Duplex unit (if fitted).6.  Operator panel.
2.  Face-up stacker.7. Front cover.
3. Paper exit.8. Paper tray.
4. Fuser unit9. Additional paper tray (if fitted)
5. Top cover.
1
2
3
45
6
7
8
9
Downloaded From ManualsPrinter.com Manuals