OKI C610n User Manual

51 – C610/C711 User’s Guide
SD Card 
Setup
This item 
is 
displayed 
only if the 
SD card 
(option) is 
installed
.
InitializeExecuteInitializes the SD Card to the 
factory default setting. Machine 
performs partition-division, and 
initializes each partition.
When this menu is executed, the 
following confirmation message 
appears.
A r e  Yo u  S u r e ?  Ye s / N o
If No is selected, you will return 
to the previous menu.
If  Yes  is selected, the following 
confirmation message appears.
Execute Now?...

52 – C610/C711 User’s Guide
SD Card 
Setup
(cont.)
Resize 
PartitionPCL nn%/
Common mm%/
PSll%/Specifies the size of partition. 
Specifies a size by ratio to the 
whole SD Card in % (1% unit).
nn,mm,ll: 1 - 98 and 
nn+mm+ll=100
The sizes are displayed in the 
partition list and can be changed 
by selecting the partition size to 
be changed. If Apply is selected, 
the following confirmation 
message appears.
Are You Sure? Yes/No
No  = return to the previous 
menu.
Yes  = Execute Now? Yes/No
No = return...

53 – C610/C711 User’s Guide
SD Card 
Setup
(cont.)
Format 
PartitionPCL
Common
PS
Formats a specified partition.
When the Enter button is 
pressed, the following 
confirmation message appears.
Are You Sure? Yes/No
No = return to the previous 
menu.
Yes = Execute Now? Yes/No
No = return to the previous 
menu. The request to execute 
partition formatting is put into 
the memory and formatting will 
be executed at next power cycle.
Yes =shutdown. The partition is 
formatted at power Off/On cycle.
System...

54 – C610/C711 User’s Guide
Time 
SetupDate 
Formatmm/dd/yyyy
dd/mm/yyyy
yyyy/mm/dd
Set desired date format.
Time Zone–12:00
~
0:00
~
+13:00
Enter the time zone for your 
country in relation to GMT.
Set in quarter units within the 
range.
Use the Menu up/down buttons 
to increment/decrement and 
press the 
Enter button to set 
and proceed to the next digit.
Daylight 
SavingOn
Off
Enable/disable daylight saving 
setting.
Time 
Setting01/01/2000 
00:00
~
01/01/2009 
00:00
~
31/12/2091 
23:59
Set current...

55 – C610/C711 User’s Guide
SettingsReset 
Settings
ExecuteResets EEPROM of CU. Resets 
User menu to the factory default.
If Execute is selected, exits 
from the menu.
Save 
Settings
ExecuteSaves menus currently set. With 
this function, the menus with 
which operation was last 
performed are saved, and 
overwrites with them menus that 
were previously saved.
When the Enter button is 
pressed, the following 
confirmation message appears.
Are You Sure? Yes/No
No = the preceding menus are 
restored.
Yes =...

56 – C610/C711 User’s Guide
Calibration
ITEMSETTINGSEXPLANATION
Auto Density 
ModeOn/OffSelects whether density 
adjustment and TRC 
compensation is automatically 
performed.
On: Density adjustment is 
automatically run under the 
engine-specified conditions, and 
reflected in TRC compensation.
Off: The printer does not 
voluntarily run density 
adjustment.
Adjust DensityExecuteIf Execute is selected, the printer 
will immediately adjust density 
and reflect it in TRC 
compensation.
This adjustment must...

57 – C610/C711 User’s Guide
Boot Menu
This menu should only be changed by the System Administrators. In order to 
gain access to this menu, follow the instructions in “How to Change the 
Settings: Administrator” on page 27 .
This menu is in English only (default settings in bold type).
Parallel Setup 
This menu controls the operatio n of the printer’s Parallel data 
interface.
Cyan/Magenta/
Yellow/Black 
TuningHighlight–3,–2,–1, 
0 ,+1,+2,+
3, Adjusts HIGHLIGHT (light area) 
of the TRC.
+ = Darker 
– =...

58 – C610/C711 User’s Guide
Bi-DirectionEnable / 
Disable ENABLE/DISABLE the bi-directional 
capability of the parallel interface.
ECP Enable / 
Disable Extended Capabilities Port, enables/disables 
this function.
Ack Width Narrow/
Medium/
Wide Sets ACK width for compatible reception.
= 0.5 µs
= 1.0 µs
= 3.0 µs
Ack / Busy 
Timing Ack in Busy / 
 
Ack while Busy ACK IN BUSY: BUSY=LOW-> The end of 
ACK pulse.
ACK WHILE BUSY: BUSY=LOW -> The 
center of ACK pulse.
I-prime 3µsec/50µsec / Disable 3...

59 – C610/C711 User’s Guide
USB Setup
This menu controls the operation of the printer’s USB data 
interface.
When you have changed any setti ngs in the USB Menu, turn the 
printer  OFF, then  ON again.
ITEMSETTINGSEXPLANATION
USB Enable / 
Disable ENABLES / DISABLES the USB port.
Speed 480 / 12  
Mbps Selects the interface speed. After setting change 
the menu, the printer restarts on exit.
Soft 
Reset Enable / 
Disable Enables or disables the SOFT RESET command.
Offline 
Receive Enable / 
Disable...

60 – C610/C711 User’s Guide
Security Setup 
Note:
This menu only displays if the optional SD card is 
installed.
ITEMSETTINGSEXPLANATION
Job 
LimitationsOff
Encrypted Job
Job limitation mode control.
Jobs other than specified ones are rejected.
Make Secure 
SD CardExecuteEnables SD Card encoding function. 
Initializes the SD card,  adds the cipher key, 
and enables encoding (security mode).
After execution, the following confirmation 
messages appear.
Are You Sure?  Yes / No
If No is selected, the...