OKI C610n User Manual

91 – C610/C711 User’s Guide
2.Note the positions of the four toner cartridges (a) and image 
drums (b). It is essential that they go back in the same order.
a
b
Downloaded From ManualsPrinter.com Manuals 

92 – C610/C711 User’s Guide
3.Holding it by its top centre, lift the image drum, complete 
with its toner cartridge, up and out of the printer.
4.Put the assembly down gently  onto a piece of paper to 
prevent toner from marking yo ur furniture and to avoid 
damaging the green drum surface.
CAUTION!
The green image drum surface at the base of the ID 
unit is very delicate and light  sensitive. Do not touch it 
and do not expose it to no rmal room light for more 
than 5 minutes. If the drum un it needs...

93 – C610/C711 User’s Guide
5.With the colored toner release lever (1) to the right, pull the 
lever towards you. This will  release the bond between the 
toner cartridge and the image drum unit.
6.Lift the right-hand end of the toner cartridge (1) and then 
draw the cartridge to the right  to release the left-hand end as 
shown (2), and withdraw the toner cartridge out of the image 
drum cartridge. Place the cartridge on a piece of paper to 
avoid marking your furniture.
7.Take the new image drum...

94 – C610/C711 User’s Guide
8.Place the toner cartridge onto the new image drum cartridge 
as shown. Push the left end in  first, and then lower the right 
end in. (It is not necessary to fi t a new toner cartridge at this 
time unless the remaining toner level is very low.)
9.Push the colored release lever away from you to lock the 
toner cartridge onto the new  image drum unit and release 
toner into it.
2
1
Downloaded From ManualsPrinter.com Manuals 

95 – C610/C711 User’s Guide
10.Holding the complete assembly by its top center, lower it into 
place in the printer, locating the pegs at each end into their 
slots in the sides of the printer cavity.
11.Finally, close the top cover and press down firmly at both 
sides so that the cover latches closed.
Note:
If you need to return or transport your printer for any 
reason, please make sure you remove the image drum 
unit beforehand and place in th e bag provided. This is to 
avoid toner spillage....

96 – C610/C711 User’s Guide
Replacing the Transfer Belt Unit ____
The belt unit is located under the four image drums.
Switch off the printer and allow the fuser to cool for about 
10 minutes before opening the cover.
1.Press the cover release and op en the printer’s top cover 
fully.
2.Note the positions of the four toner cartridges (a) and image 
drums (b). It is e
ssential that they go back in the same order. 
WARNING!
If the printer has been po wered on, the fuser will be 
hot. This area is clearly...

97 – C610/C711 User’s Guide
3.Lift each of the image drum units out of the printer and place 
them in a safe place away from direct sources of heat and 
light.
CAUTION!
The green image drum surface at the base of each 
cartridge is very delicate and light sensitive. Do not 
touch it and do not expose it to normal room light for 
more than 5 minutes. If the  drum unit needs to be out 
of the printer for longer th an this, please wrap the 
cartridge inside a black plastic bag to keep it away 
from light....

98 – C610/C711 User’s Guide
4.Locate the two fasteners (a) at each side of the belt and the 
lifting bar
 (b) at the front end.
5.Turn the two fasteners 90° to the left. This will release the 
belt from the printer chassis.
6.Pull the lifting bar (b) upwards so that the belt tilts up 
towards the front, and withdraw  the belt unit (c) from the 
printer.
a
a
b
c
Downloaded From ManualsPrinter.com Manuals 

99 – C610/C711 User’s Guide
7.Lower the new belt unit into place, with the lifting bar at the 
front and the drive gear towards the rear of the printer. 
Locate the drive gear into the gear inside the printer by the 
rear left corner of the unit, and  lower the belt unit flat inside 
the printer.
Downloaded From ManualsPrinter.com Manuals 

100 – C610/C711 User’s Guide
8.Turn the two fasteners (a) 90° to the right until they lock. This will 
secure the belt unit in place.
9.Replace the four image drums,  complete with their toner 
cartridges, into the printer in  the same sequence as they 
came out: cyan (nearest the  rear), magenta, yellow and 
black (nearest the front).
10.Finally, close the top cover and press down firmly at both 
sides so that the cover latches closed.
a
a
Downloaded From ManualsPrinter.com Manuals