OKI C610dn User Manual

							
51 – C610/C711 User’s Guide
SD Card 
Setup
This item 
is 
displayed 
only if the 
SD card 
(option) is 
installed
.
InitializeExecuteInitializes the SD Card to the 
factory default setting. Machine 
performs partition-division, and 
initializes each partition.
When this menu is executed, the 
following confirmation message 
appears.
A r e  Yo u  S u r e ?  Ye s / N o
If No is selected, you will return 
to the previous menu.
If  Yes  is selected, the following 
confirmation message appears.
Execute Now? Yes/No
If  No  is selected, you will return 
to the previous menu.
The request to execute SD Card 
initialization is put into the 
memory and initialization will be 
executed at the next power 
cycle.
If  Yes  is selected, shutdown 
takes place, and the SD Card is 
initialized at power Off/On cycle.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
52 – C610/C711 User’s Guide
SD Card 
Setup
(cont.)
Resize 
PartitionPCL nn%/
Common mm%/
PSll%/Specifies the size of partition. 
Specifies a size by ratio to the 
whole SD Card in % (1% unit).
nn,mm,ll: 1 - 98 and 
nn+mm+ll=100
The sizes are displayed in the 
partition list and can be changed 
by selecting the partition size to 
be changed. If Apply is selected, 
the following confirmation 
message appears.
Are You Sure? Yes/No
No  = return to the previous 
menu.
Yes  = Execute Now? Yes/No
No = return to the previous 
menu. The request is put into the 
memory and the SD Card 
initialization and partition size 
change will be executed at next 
power cycle.
 
Yes = shutdown. SD Card 
initialization and partition size 
change will be executed at Power 
Off/On cycle. 
(If one partition 
size is modified, the others are 
also modified.) If any partition 
size is modified, Initialization of 
SD Card needs to be executed as 
well.
If a previously used SD Card is 
installed, SD Card initialization 
also takes place. If an SD Card, 
which has been used before, is 
installed, the layout of this menu 
may be different from that of 
each partition. (The previously 
used layout will be displayed.)
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
53 – C610/C711 User’s Guide
SD Card 
Setup
(cont.)
Format 
PartitionPCL
Common
PS
Formats a specified partition.
When the Enter button is 
pressed, the following 
confirmation message appears.
Are You Sure? Yes/No
No = return to the previous 
menu.
Yes = Execute Now? Yes/No
No = return to the previous 
menu. The request to execute 
partition formatting is put into 
the memory and formatting will 
be executed at next power cycle.
Yes =shutdown. The partition is 
formatted at power Off/On cycle.
System 
SetupNear Life 
StatusEnable/DisableSet LCD panel control at the time 
of near-life warning for drum, 
fuser and belt.
Enable: Display a near-life 
warning.
Disable: Do not display a near-
life warning.
Near Life 
LEDEnable/DisableControls the settings of the 
Attention LED when near end of 
life warning of toner, drum, fuser, 
or belt occurs.
Attention LED is lit when 
enabled, not lit if disabled. 
(Displays LCD message.)
The temporary recovery by 
opening and closing of the cover 
in Life error is not included.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
54 – C610/C711 User’s Guide
Time 
SetupDate 
Formatmm/dd/yyyy
dd/mm/yyyy
yyyy/mm/dd
Set desired date format.
Time Zone–12:00
~
0:00
~
+13:00
Enter the time zone for your 
country in relation to GMT.
Set in quarter units within the 
range.
Use the Menu up/down buttons 
to increment/decrement and 
press the 
Enter button to set 
and proceed to the next digit.
Daylight 
SavingOn
Off
Enable/disable daylight saving 
setting.
Time 
Setting01/01/2000 
00:00
~
01/01/2009 
00:00
~
31/12/2091 
23:59
Set current date and time.
Display format follows the 
settings selected in Date Format.
Change 
PasswordNew 
PasswordxxxxxxxxxxxxxxSets a new password to enter 
Admin Setup menu.
From 6 to 12 alpha/numeric 
digits can be entered.
Verify  
passwordxxxxxxxxxxxxxxForces the User to input the new 
password to enter Admin Setup.
From 6 to 12 alpha/numeric 
digits can be entered.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
55 – C610/C711 User’s Guide
SettingsReset 
Settings
ExecuteResets EEPROM of CU. Resets 
User menu to the factory default.
If Execute is selected, exits 
from the menu.
Save 
Settings
ExecuteSaves menus currently set. With 
this function, the menus with 
which operation was last 
performed are saved, and 
overwrites with them menus that 
were previously saved.
When the Enter button is 
pressed, the following 
confirmation message appears.
Are You Sure? Yes/No
No = the preceding menus are 
restored.
Yes = the current menu settings 
are saved and this menu is 
exited.
Restore 
SettingsExecuteChanges to the menu setting 
saved.
When the  Enter button is 
pressed, the following 
confirmation message appears.
Are You Sure?  Yes/No      
If  No  is selected, the previous 
menu display resumes. 
If  Yes  is selected, changes to the 
menu settings are saved and this 
menu is exited.
Display Condition: The menu 
settings are saved. 
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
56 – C610/C711 User’s Guide
Calibration
ITEMSETTINGSEXPLANATION
Auto Density 
ModeOn/OffSelects whether density 
adjustment and TRC 
compensation is automatically 
performed.
On: Density adjustment is 
automatically run under the 
engine-specified conditions, and 
reflected in TRC compensation.
Off: The printer does not 
voluntarily run density 
adjustment.
Adjust DensityExecuteIf Execute is selected, the printer 
will immediately adjust density 
and reflect it in TRC 
compensation.
This adjustment must be 
executed when the printer is 
idling. It can become invalid 
if executed in any other state.
Adjust 
RegistrationExecuteWhen this menu is selected, the 
printer performs AutoAdjust 
Registration.
This adjustment must be 
executed when the printer is 
idling. 
Print Tuning 
PatternExecutePrints the pattern for the user to 
adjust TRC. Ordinarily, this 
function is not needed because 
TRC is automatically adjusted to 
the recommended levels through 
density adjustment and TRC 
compensation.
Adjustment results will be 
reflected as offset values 
(addition) to the corrections 
through the Adjust Density/TRC 
Compensation function.
Downloaded From ManualsPrinter.com Manuals 
						

							
57 – C610/C711 User’s Guide
Boot Menu
This menu should only be changed by the System Administrators. In order to 
gain access to this menu, follow the instructions in “How to Change the 
Settings: Administrator” on page 27 .
This menu is in English only (default settings in bold type).
Parallel Setup 
This menu controls the operatio n of the printer’s Parallel data 
interface.
Cyan/Magenta/
Yellow/Black 
TuningHighlight–3,–2,–1, 
0 ,+1,+2,+
3, Adjusts HIGHLIGHT (light area) 
of the TRC.
+ = Darker 
– = Lighter
Mid-Tone–3,–2,–1, 
0 ,+1,+2,+
3, Adjusts MID-TONE area of the 
TRC.
+ = Darker 
– = Lighter
Dark–3,–2,–1, 
0 ,+1,+2,+
3, Adjusts DARK area of the TRC.
+ = Darker 
– = Lighter
Cyan/Magenta/
Yellow/Black 
Darkness–3,–2,–1, 
0 ,+1,+2,+
3, Adjusts the engine density.
Note:
This menu item only applies to the C711.
ITEMSETTINGSEXPLANATION
Enter 
Password xxxxxxxxxxxx Enter a password to access the Boot menu.
Password should be from 6 to 12 digits of 
alpha/numeric characters (or mix) 
The default value is “aaaaaa”
Parallel Enable / 
Disable Enables or disables the parallel port.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
58 – C610/C711 User’s Guide
Bi-DirectionEnable / 
Disable ENABLE/DISABLE the bi-directional 
capability of the parallel interface.
ECP Enable / 
Disable Extended Capabilities Port, enables/disables 
this function.
Ack Width Narrow/
Medium/
Wide Sets ACK width for compatible reception.
= 0.5 µs
= 1.0 µs
= 3.0 µs
Ack / Busy 
Timing Ack in Busy / 
 
Ack while Busy ACK IN BUSY: BUSY=LOW-> The end of 
ACK pulse.
ACK WHILE BUSY: BUSY=LOW -> The 
center of ACK pulse.
I-prime 3µsec/50µsec / Disable 3 microseconds: Enabled with the 3 µs nInit 
signal.
50 microseconds: Enabled with the 50 µs 
nInit signal.
Offline 
Receive Enable / 
Disable To Enable/disable this function. When set to 
Enable, the interface retains a receive 
possible state even when switching to 
Offline. Interface sends the BUSY signal 
only when the receive buffer is full or a 
service call occurs.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
59 – C610/C711 User’s Guide
USB Setup
This menu controls the operation of the printer’s USB data 
interface.
When you have changed any setti ngs in the USB Menu, turn the 
printer  OFF, then  ON again.
ITEMSETTINGSEXPLANATION
USB Enable / 
Disable ENABLES / DISABLES the USB port.
Speed 480 / 12  
Mbps Selects the interface speed. After setting change 
the menu, the printer restarts on exit.
Soft 
Reset Enable / 
Disable Enables or disables the SOFT RESET command.
Offline 
Receive Enable / 
Disable OFFLINE RECEIVE.
Serial 
Number Enable
 / 
Disable Specifies whether to ENABLE or DISABLE a USB 
serial number.
The USB serial number is used to identify the 
USB device connected to your PC.
Downloaded From ManualsPrinter.com Manuals 
						

							
60 – C610/C711 User’s Guide
Security Setup 
Note:
This menu only displays if the optional SD card is 
installed.
ITEMSETTINGSEXPLANATION
Job 
LimitationsOff
Encrypted Job
Job limitation mode control.
Jobs other than specified ones are rejected.
Make Secure 
SD CardExecuteEnables SD Card encoding function. 
Initializes the SD card,  adds the cipher key, 
and enables encoding (security mode).
After execution, the following confirmation 
messages appear.
Are You Sure?  Yes / No
If No is selected, the display returns to the 
previous menu.
If Yes is selected, the printer automatically 
reboots and the encoding function is turned 
on.
Display Conditions:
SD Card is installed, SD Card encoding func-
tion invalidity and Storage Setup > Enable 
Initialization > Yes
Make Normal 
SD CardExecuteSets SD Card encoding to invalid.
Initializes the SD card, deletes the cipher 
key, and encoding (security mode) 
information is turned off.
After execution, the following confirmation 
messages appear.
Are You Sure?  Yes / No
If  No  is selected, the display returns to the 
previous menu.
If  Yes  is selected, the printer automatically 
reboots and the encoding function is turned 
on.
Display Conditions:
SD Card is installed, SD Card encoding 
function invalidity and  Storage Setup > 
Enable Initialization > Yes
Downloaded From ManualsPrinter.com Manuals