OKI C610dn User Manual

							
31 – C610/C711 User’s Guide
Print Secure Job Menu    
Note:
This menu only displays if the optional SD card is 
installed or on a C610hdn with a hard disk drive 
installed.
ITEMACTIONEXPLANATION
Encrypted 
JobNot Found
Print
Delete
Used for printing an encrypted authentication 
print job (Encrypted Job) stored in the SD card.
After inputting a password, Searching Job is 
displayed until a job appropriate for the 
password is found.
(Searching time increases in proportion to the 
number of jobs stored in the SD card, and the 
printer may take up to 20 sec.)
The search can be cancelled by holding down 
the Cancel button.
Not Found will be displayed where a file, which 
could be printed is not available.
The following message will appear if a printable 
file is available.
Encrypted Job
Print
Delete
A set of all jobs will be printed if Print is selected 
and the Enter button is pressed.
The following message will appear if Delete is 
selected:
Are You Sure? Yes / No
The display will return to  the source menu if No 
is selected.
All jobs will be deleted if Yes is selected.
Print jobs with encrypted authentication stored 
in the SD card are deleted by a delete method 
specified by the driver af ter printing or a delete 
instruction from the menu.
Downloaded From ManualsPrinter.com Manuals 
						

							
32 – C610/C711 User’s Guide
Stored JobNot Found
Print
Delete
Used to print out a stored job in the SD card.
Not Found will be displayed where a file, which 
could be printed is not available.
The following message will appear if a printable 
file is available.
Stored Job
Print
Delete
When  Print is selected,  Set Collating Amount 
is displayed and the number of pages to print 
can be specified.
Specify the number of pages to print and press 
the  Enter  button.
The following message will appear if  Delete is 
selected:
Are You Sure? Yes / No
If  No  is selected, the display will return to the 
previous menu.
If  Yes  is selected, all jobs will be deleted.
ITEMACTIONEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
33 – C610/C711 User’s Guide
Menus Menu 
ITEMACTIONEXPLANATION
Tr a y  
ConfigurationPaper feed 
Default: Tray 1
Select tray. Select by scroll and 
Enter button.
Auto Tray Switch 
Default:  On
Switches Auto ON/OFF. Select by 
scroll and  Enter button.
Tr a y  S e q u e n c e 
Default:  Down
Selects Tray sequence  Down/Up /
Paper feed Tray . Select by scroll 
and  Enter  button.
Unit of Measurement 
Default:  inches
Selects UOM inches or millimeter. 
Select by scroll and  Enter button.
Tr a y 1  C o n f i g 
Default:
Configure  Paper Size /Media 
Type /Media Weight . Select by 
scroll and  Enter button.
Paper Size :
C610 
A4/A5/A6/B5/Legal14/
Legal13.5/Legal13/
Letter /Executive/Custom
C711
Cassette /Custom
Media Type : Plain /
Letterhead/Bond/
Recycled/Card Stock/
 
Rough/Glossy/ 
*USER TYPE 1-5
*USER TYPE 1 to 5 are displayed 
only if registered in the host PC.
Media Weight : Light /
Medium Light/Medium/ 
Heavy/Ultra Heavy1/
Ultra Heavy2
Downloaded From ManualsPrinter.com Manuals 
						

							
34 – C610/C711 User’s Guide
Tray 
Configuration 
(cont.)MP Tray Config
Paper Size:
•A4/A5/A6/B5
• Legal14/Legal 13.5/Legal13
• Letter
• Executive
•Custom
•Com-9 Envelope
•Com-10 Envelope
•Monarch Envelope
•DL Envelope
•C5
•Index Card
Configure Paper Size/Media 
Type/Media Weight/Tray 
Usage.
Select by scroll and Enter button.
Media Type:
• Plain
• Letterhead
• Film
•Labels
•Bond
•Recycled
•Card Stock
•Rough
• Glossy
•USERTYPE 1-5
USERTYPE 1 to 5 are displayed 
only if registered in the host PC.
Paper weight 189 ~ 250 g/m2
 Media Weight:
•Light
•Medium Light
•Medium
•Heavy
•Ultra  Heavy 1
• Ultra Heavy 2
• Ultra Heavy 3
Tray usage:
• When Mismatching
•Do Not Use
Sets MPTray usage.
When Mismatching: if paper 
mismatch occurs, paper is 
requested from the MPTray instead 
of the specified tray.
Do Not Use: sets MPTray 
unavailable both in Auto Tray 
Select and Auto Tray Switch.
ITEMACTIONEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
35 – C610/C711 User’s Guide
Tr a y  2  C o n f i g
Tr a y  3  C o n f i g
Note: only present if option 
installed
System Adjust Power Save Time
Default: 30
Select from  1/2/3/4/5/10/15/
30/60/120/180 Minutes . 
Select by scroll and  Enter button.
Sleep Time
Default:  10
Select from  1/2/3/4/5/10/15/
30/60/120/180 Minutes .
Select by scroll and Enter button.
Clearable Warning
Default: ONLINE
Select from:  ONLINE/Job . Select 
by scroll and  Enter button. PS job 
only.
Auto Continue
Default:  Off
Select from  On/Off. Select by 
scroll and  Enter button.
Manual Timeout
Default:  60
Select from  Off/30 seconds/60 
seconds .
Select by scroll and  Enter button.
Wait T ime out
Default:  40
Select from  Off/5/10/20/30/
40/50/60/90/120/150/180/
210/240/270/300 seconds. 
Select by scroll and  Enter button.
Low Toner
Default:  Continue
Select action to take when toner 
sensor indicates low toner. Select 
from Continue/Stop . Select by 
scroll and  Enter button.
Jam Recovery
Default:  On
Select from  On/Off. Select by 
scroll and  Enter button.
Error Report
Default:  Off
Select from  On/Off. Select by 
scroll and  Enter button.
Print Position Adjust
Default:  0.00
Select from  X Adjust/Y Adjust/
Duplex X Adjust/Duplex Y 
adjust . Select by scroll and  Enter 
button. Define measurement.
ITEMACTIONEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
36 – C610/C711 User’s Guide
System Adjust 
(cont.)
Paper Black Setting  
–2/–1/0/+1/+2
Default: 0
Used for fine adjustment of the 
black print on paper.
Paper color Setting 
–2/–1/0/+1/+2
Default: 0
Used for fine adjustment of the 
color print on paper.
Film Black Setting  
–2/–1/0/+1/+2
Default: 0
Used for fine adjustment of the 
black print on film.
Film Color Setting  
–2/–1/0/+1/+2
Default: 0
Used for fine adjustment of the 
color print on film.
SMR Setting  
+3/+2/+1/0/–1/–2/–3
Default: 0
To correct variations in print 
results caused by temperature/
humidity conditions and difference 
in print density/frequency. Change 
the setting when print quality is 
uneven.
BG Setting 
+3/+2/+1 /0 /–1/–2/–3
Default:  0
To correct variations in print 
results caused by temperature/
humility conditions and difference 
in print density/frequency. Change 
the setting when background is 
dark.
Drum Cleaning
Default:Off
Sets whether to rotate the drum in 
idle prior to printing in order to 
reduce horizontal white lines. This 
will shorten the ID life by as much 
as this rotation. Select by scroll 
and Enter  button.
Hex Dump
Execute
Prints out data received from the 
host PC in the hexadecimal Dump. 
Turning off the power supply 
switch restores Normal Mode.
ITEMACTIONEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
37 – C610/C711 User’s Guide
Admin Setup
ITEMSETTINGSEXPLANATION
Enter 
PasswordxxxxxxxxxxxxEnter a password to gain entry to 
the Admin Setup menu.
Password should be from 6 to 12 
digits of alpha/numeric 
characters (or mix) 
The default value is aaaaaa
Network 
SetupTCP/IPEnable
Disable
Sets TCP/IP Protocol.
Enable: TCP/IP Protocol is 
available.
Disable: TCP/IP Protocol is not 
available.
IP Version
IP v4 
IP v4+v6 
IP v6
Sets up the IP version.
Operates with IPv4 for IPv4 (not 
valid with IPv6).
Operates with both IPv4 and 
IPv6 for IPv4+v6.
Operates with IPv6 for IPv6 (not 
valid with IPv4).
There is only IPv4 and IPv4+v6 
as normal value.
From this stage, if IPv6 only is 
set from UI, for example Telnet, 
“IPv6” appears as the value of IP 
Version on the operation panel. 
“IPv6” will disappear from the 
value if “IP v4” or “IP v4+v6” is 
selected.
Display Condition:  
TCP/IP should be enabled.
NetBEUIEnable
Disable
Sets Enable/Disable of NETBEUI 
Protocol.
NetBIOS 
over TCPEnable
Disable
Sets Enable/Disable of NetBIOS 
over TCP protocol.
Display Conditions:
• TCP/IP should be enabled.
• IP Version is not IPv6.
Downloaded From ManualsPrinter.com Manuals 
						

							
38 – C610/C711 User’s Guide
Network 
Setup
(cont.)
NetWareEnable
Disable
Sets Enable/Disable of NetWare 
Protocol.
EtherTalkEnable
Disable
Sets Enable/Disable of EtherTalk 
Protocol.
Frame TypeAuto
802.2
802.3
Ethernet II
SNAP
Sets the frame type.
Display Condition: Netware 
should be enabled.
IP Address 
SetAuto
Manual
Sets the IP Address setting 
method. 
Display Conditions:
• TCP/IP should be enabled.
• IP Version is not IPv6.
IPv4 
Addressxxx.xxx.xxx.xxxSets the IPv4 Address.
Display Conditions:
• TCP/IP should be enabled.
• IP Version is not IPv6.
Subnet 
Maskxxx.xxx.xxx.xxxSets the Subnet Mask.
Display Conditions:
• TCP/IP should be enabled.
• IP Version is not IPv6.
Gateway 
Addressxxx.xxx.xxx.xxxSets the Gateway (default 
router) address. “0.0.0.0” means 
that there is no router.
Display Conditions:
• TCP/IP should be enabled.
• IP Version is not IPv6.
WebEnable
Disable
Sets Enable/Disable of Web.
Enable: Web/IPP is available. 
Disable: Web/IPP is not 
available.
 
Display Condition: TCP/IP should 
be enabled.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
39 – C610/C711 User’s Guide
Network 
Setup
(cont.)
Te l n e tEnable
Disable
Sets Enable/Disable of Telnet.
Enable: Telnet is available. 
Disable: Telnet is not available. 
Display Condition:TCP/IP should 
be enabled.
FTPEnable
Disable
Sets Enable/Disable of FTP.
Enable: FTP is available. 
Disable: FTP is not available. 
Display Condition: TCP/IP should 
be enabled.
IPSecEnable
Disable
Sets Enable/Disable of IPSec. 
Enable via the web.
Enable: IPSec is available.
Disable: IPSec is not available.
SNMPEnable
Disable
Sets Enable/Disable of SNMP.
Enable: SNMP is available. 
Disable: SNMP is not available. 
Display Condition: TCP/IP or 
NetWare should be enabled.
Network 
ScaleNormal
Small
When Normal  is selected, the 
network can work effectively 
even when it is connected to a 
HUB that has a spanning tree 
feature. However, printer start 
up time gets longer when 
computers are connected with 
two or three small LANs.
When  Small is selected, 
computers can cover from two or 
three small LANs to a large LAN, 
but may not work effectively 
when the network is connected 
to a HUB with a spanning tree 
feature.
Hub Link 
SettingAuto 
Negotiate
100Base-TX Full
100Base-TX Half
10Base-T Full
10Base-T Half
Sets a method to link to a HUB. 
When  Auto is set, a connection 
method to a HUB is selected 
automatically 
and attempts to 
connect
. If another method is 
selected, attempts to connect to 
a HUB only by the selected 
connection method.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
40 – C610/C711 User’s Guide
Network 
Setup
(cont.)
Factory 
Defaults?ExecuteSpecifies whether to initialize the 
network factory default settings 
for the Network.
Print 
SetupPersonalityAuto
PostScript
PCL
XPS
IBM PPR
EPSON FX
Selects a printer language.
Copies1- 999Selects the number of copies.
This setting is disabled for Local 
Print except for Demo Page.
DuplexOn/ OffSpecifies Duplex print (option) if 
a Duplex unit is installed and 
enabled
BindingLong Edge
Short Edge
Specifies Binding in duplex 
printing.
Display Condition: a duplex unit 
is installed and enabled.
Refer to “Duplex”, above.
Media 
CheckEnable
Disable
Sets whether the printer checks 
the matching of printed data size 
and that of the tray. Only 
standard sizes are checked.
Resolution600dpi
600x1200dpi
600dpi multi-
level.
Sets default resolution.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals