Oce ColorWave 600 User Manual

Set the 'Production Plus' setting
Introduction
You can use the 'Production Plus' setting in the Océ Express WebTools to define how
the Océ
 
ColorWave 600 must interpret the 'Production' 'Print Setting'.
Before 
you begin This 
setting is editable for the Key operator or Power user.
How 
to set the 'Production Plus' setting 1. Click 
'Preferences' - 'Print job defaults'.
2. Click 
'Edit' in the 'Basic' bar or click the value of the...

Set the 'Economy monochrome enhanced' setting
Introduction
You can use the 'Economy monochrome enhanced' setting in the Océ Express WebTools
to define how the Océ ColorWave 600 must interpret the 'Economy' 'Print Setting'.
Before 
you begin This 
setting is editable for the Key operator or Power user.
How 
to set the 'Economy monochrome enhanced' setting 1. Click 
'Preferences' - 'Print job defaults'.
2. Click 
'Edit' in the 'Basic'...

Set the 'Océ Print Assistant Behavior'
Introduction
This setting is only used when the 'Print Setting' is set to 'Océ Print Assistant'.
The 
'Océ Print Assistant' decides what print setting ('Production', 'Production Plus',
'Presentation' or
 'Economy') must be used, based on the average toner coverage of the
print.
You can

 use 
the 'Océ Print Assistant Behavior' setting to influence the average toner
coverage 
limits that the...

Set the 'PDF processing optimization'
Introduction
The 'PDF processing optimization' setting allows you to tune the processing of PDF files
to optimize for quality or performance.
You can
 choose 
one of following values.
• 'Optimize for
 print quality'
Select this

 value if print quality is an important factor.
• 'Optimize for

 performance'
Select 

this value if PDF processing performance is more important than print quality.
Before you begin This 
setting is editable...

Set the 'PDF wipeout correction'
Introduction
The 'PDF wipeout correction' setting allows you to print PDF documents containing
unusual
 solid black areas which mask some 
parts of the drawing. When enabled, these
PDF documents
 
will be printed correctly but the processing of the PDF files will be
slower.
 When disabled the correction is not applied.
Before

 you begin This 
setting is editable for the Key operator or Power user.
How 
to set the 'PDF wipeout correction' 1. Click...

Set the 'Long plot mode'
Introduction
The 'Long plot mode' setting allows you to produce prints with a print length up to 175
meters.
When the 'Long plot mode' is disabled you can produce prints with a print length up to
22 meters. The print quality matches the print quality that you defined for your print
job.
When
 the 'Long plot mode' is enabled you can produce prints with a print length up to
175
 meters. To be able to print very long prints, the print quality may be...

Set the 'Automatic roll switch'
Introduction
You can choose one of following values.
• 'Enabled'
Select 
this value if you have two or more media rolls that contain identical media (the
same 
media type and media size). In that case, the printer can automatically switch
to 
an alternative media roll when a roll runs out of media and continue printing.
• 'Disabled'
Select this
 value if all media rolls contain 
different media types or media sizes.
There are
 two 
options:
If you...

Set the 'Spool threshold'
Introduction
When the job memory is full the printer can not receive new jobs. You can tune the
'Spool threshold' to define the spool capacity for specific job types. Allow a higher capac-
ity for small jobs if you select Low. Select High if you want to reduce the risk of aborting
file 
transfer of large print jobs if the job memory is full.
You can
 
choose one of following values.
• 'Low'
Select this
 value if you 
want to allow a higher capacity for...

Set the 'Print while RIP' setting
Introduction
This setting is a performance optimization setting. When "Print while RIP" is enabled,
for Economy
 prints, the printer starts to print an image during the rasterization of the
image. Occasionally

 the rasterization of the image cannot keep up with 
the print speed.
In 
that case the print process will be aborted (error code 22801) and the print will be re-
covered afterwards. To prevent this you can disable this setting. Even when disabled,...

Set the 'Rotation' mode
Introduction
The 'Rotation' setting allows you to rotate the image according to predefined rotation
values 
or you can let the printer perform the rotation automatically.
Choose 
one of the following values.
• 'No 
rotation'
• '90°'
• '180°'
• '270°'
• 'Auto rotate portrait'
• 'Auto rotate

 landscape'
• 'Auto rotate

 portrait with additional 180° rotation'
• 'Auto

 rotate landscape with 
additional 180°...