Nitsuko Ds1000 Hardware Manual

5. Maintenance
Options and SMDR
5-5
MODEM INSTALLATIONFigure 5-2  CONNECTING A MODEM
80200 - 24
RS-232 Port
Mod 8
Patch CordTo trunk
Modem Power
SupplyP/N 85981 

5-6
MAKING YOUR OWN DATA CABLES
80200 - 35
1Mod-8
1
2
3
4
5
6
7
8 DSR
DCD
DTR
SG
RD
TD
CTS
RTSDTR
DCD
DSR
SG
TD
RD
RTS
CTS
R1 DB-9
4
1
6
5
3
2
7
8
98
9
6
5
1
80200-36
1 8
14
25
1
13
Mod-8
1
2
3
4
5
6
7
8 DSR
DCD
DTR
SG
RD
TD
CTS
RTSDSR
DCD
DTR
SG
RD
TD
CTS
RTS DB-25
6
8
20
7
3
2
5
4
Figure 5-3  MAKING YOUR OWN DATA CABLES
DSRMod-8 Mod-8
Latch faces
down
1
RTS 2RD 3SG
4TD 5CTS 6DTR
7DCD
81
2
3
4
5
6
7
8
8
18
1
80200 - 25 

5. Maintenance
Options and SMDR
5-7
SYSTEM RESET
Resetting Your System (Figure 5-4)
You may need to reset your system for troubleshooting purposes.
To reset your system:
1. Make sure the RUN/LOAD switch is set to RUN.
2. Following the illustration at right, press the red reset switch.
Your system will automatically restart.
FIGURE 5-4  RESETTING YOUR SYSTEM
Reset Switch
80200 - 31
RUN/LOAD
Switch 

5-8
— For Your Notes — 

6. Specifications
and Parts
6-1
Section 6, SPECIFICATIONS AND PARTS LIST
In this section . . . PageSpecifications  . . . . . . . . . . . . . . . . . . . . . . .6-2
Parts List  . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6 

6-2
SPECIFICATIONS
System Capacities
Power Failure Telephones: 1
DSS Consoles: 1 max. per keyset, 4 max.
per system
External Paging Zones: 1
Internal Paging Zones: 8 (7 and All Call)
Page Audio  Output: 1
Music Input: 1
Conference Circuits Conference circuits dynam-
ically allocated, with  8 par-
ties max. per Conference.
REJ Recording Jack Units 1 max. per keyset
System Capacities
Cabinets: 1
Talk Timeslots (Intercom/line): Non-blocking
Analog Trunks (CO/PBX lines): Base: 3
Expansion: 3
Total: 6
Digital...

6. Specifications
and Parts
6-3
SPECIFICATIONS
Electrical Specifications
Power Supply: 120 VAC ±- 10% @ 50-60 Hz
Output Power 35 W
Input Current 550 mA
VA 6 6  VA
Kwh .066 KwH
BTU 225 BTU
Grounding Requirements: 12 AWG copper wire
Environmental Specifications
Cabinet, Key Telephones and Digital Door Box
Temperature: 0-45
oC (32-113
oF)
Humidity: 10-95% (non-condensing)
Digital Door Box not intended for outdoor installation.
Analog Door Box
Temperature: -20-60
oC (4-140
oF)
Humidity: 10-95%...

6-4
SPECIFICATIONS
Relay Contacts
Contact Configuration: Normally open
Maximum Load: 0.5A @ 120 VAC
1A @ 24 VDC
Maximum Carry Current 2A
Maximum Switched Voltage 120 VAC or 60 VDC
Maximum Switched Power 60 VA or 24 W
Minimum Switched Current 1 mA
Minimum Switched Voltage 1 VDC
Minimum Switched Power 0.05 mW
Maximum Initial Contact Resistance: 100 mOhms
External Paging
Output Impedance: 600 Ohm
Output Level: 0 dBr @ 1.0 KHz
Mechanical Specifications
Equipment Width Depth Height Weight
Cabinet 13 3/4””2...

6. Specifications
and Parts
6-5
SPECIFICATIONS
Cabling Requirements
1. Do not run station cable parallel with the AC source, telex or com-
puter, etc. If the cables are near cable runs to those devices, use
shielded cable with grounded shields or install the cable in conduit.
2. When cables must be run on the floor, use cable protectors.
3. Cable runs for key telephones, single line telephones, Door Boxes
and 3-ACI Modules must be a dedicated, isolated cable pair.Device Cable Type Cable Run Length (ft)...

6-6
PARTS LIST
Common Equipment
Description Part Number
DS1000 3 x 8 x 4 Cabinet 80200
DS1000 3 x 8 x 4 Expansion Board 80221
DB9 to Mod-8 Adaptor 85980
DB25 to Mod-8 Adaptor 85981
Peripheral Station Equipment
Description Part Number
Digital Door Box 80560
Analog Door Box 92245
Station Equipment
Description Part Number
34-Button Super Display Telephone 80673
34-Button Display Telephone 80663
22-Button Telephone 80570
22-Button Display Telephone 80573
24-Button DSS Console 80556
110-Button DSS Console...