Nitsuko Digital System Feature And Terminal Programming Manual

QM- MUSIC/RELAY CONTROL, MOH
Description
Enter Y to enable Music on Hold; N to disable.  Refer to the system Hardware Manual for additional installation
details.
Conditions 
Music On Hold (for internal extensions) uses the fourth trunk circuit on the first CO Module in the main CEU.
You cannot use the fourth trunk circuit for trunks.  (Music on Hold for outside calls does not use the trunk cir-
cuit.)  If you want MOH for trunks 9-16, connect the MOH terminals on the main CEU to the MOH terminals
on the...

QM- MUSIC/RELAY CONTROL, MOH ON TRANSFER
Description
Use this option to determine if transferred callers should hear Music on Hold or ringback tone.  If enabled (Y),
transferred callers hear Music on Hold while they wait for their call to go through.  If disabled (N), transferred
callers hear ringback tone.
For this option to function, you must have:
•Music on Hold installed (refer to the Music on Hold feature)
•Designated a trunk in QM- MOH
Conditions 
None
Default Value
MOH for transferred calls...

QM- MUSIC/RELAY CONTROL, ENABLE EXTERNAL ZONE 1
Description
This option is external page/night audible.  Enter Y(es) to enable All Call Paging and Night Audible on the main
CEU PA terminals.  Enter N(o) to disable Paging and audible.
Conditions 
None
Default Value
No trunk assigned (00).
Feature Reference
Night Answer (Off-Hours Ringing)
Paging
Tenant Service
Instructions
To enter data on the PRF:
1. For QM- Enable External Zone 1 on Table 9, enter Y or N.
To enter data at the programming terminal:
1....

QM- MUSIC/RELAY CONTROL, INHIBIT AUDIBLE RING
Description
Use this option to enable/disable audible ring on the trunk port you designate in QM- Enable External Zone 1.
If enabled (N), night audible can occur.  If disabled (Y), night audible cannot occur.
Conditions 
None
Default Value
Audible ring enabled (N).
Feature Reference
Night Answer (Off-Hours Ringing)
Instructions
To enter data on the PRF:
1. For QM- Inhibit Audible Ring on Table 9, enter Y or N.
To enter data at the programming terminal:
1....

- For Your Notes -
Q- SYSTEM-WIDE PROGRAMMING
QM- MUSIC/RELAY CONTROL, INHIBIT AUDIBLE RING
508   PROGRAMMING N1870SWG04   Issue 1-0 

Q- SYSTEM WIDE PROGRAMMINGQM- MUSIC/RELAY CONTROL, ENABLE EXTERNAL ZONE 2
Description
Use this option to enable/disable External Paging on the expansion CEU PA terminals.  If enabled (Y), External
Paging zone 1 and All Call broadcast over the expansion CEU PA terminals.  If disabled (N), paging does not
broadcast over the expansion CEU PA terminals.  Refer to the system Hardware Manual for additional installa-
tion details.
Conditions 
External Paging uses the fourth trunk circuit on the first CO Module...

QM- MUSIC/RELAY CONTROL, BGM ON EXTERNAL PAGE ZONES
Description
Use this option to allow/disallow Background Music to play over the External Paging zones.  If allowed (Y),
BGM will play over all the external zones (All Call and 1-3) when they are idle. If disallowed, BGM will not
play.  Refer to the system Hardware Manual and the Background Music feature for additional information on
Background Music.
Conditions 
Always make a test page after enabling this option.
Default Value
BGM will not play over...

QM- MUSIC/RELAY CONTROL, INTERRUPTED RING RELAYS
Description
Use this option to enable/disable interrupted closure for the external relays when used for ringing.  If enabled
(Y), relays pulse one second closed/three seconds open when activated.  If disabled (N), relays have continuous
closure when activated. This option affects all the external relays.  All external relays are normally open.
Conditions 
None
Default Value
Relays provide continuous closure (N) when activated.
Feature Reference
External...

QM- MUSIC/RELAY CONTROL, EXTERNAL PAGE MUSIC GAIN
Description
Use this option to adjust the gain for the Background Music that plays over the External Paging ports.  The ad-
justment you make with this option does not affect the volume of internal Background Music.  You can make
fine adjustments to internal and external BGM volumes separately.  The choices are:
-12 dB loss
-6 dB loss
-3 dB loss
0 dB
+3 dB gain
+6 dB gain
This option only appears if you enter Y for QM- BGM on External Page Zones.
Note:
A...

QM- MUSIC/RELAY CONTROL, RELAY CONTROL-PAGEOWNER
Description
Use this option to assign the Pageowner for ringer and Paging relay control, as shown below.  You program this
option separately for each of the two relays.
For ringing...
The relay activates for Night Mode calls if:
•QM- Page Owner entry is the main attendant (usually 300)
The relay activates when an extension rings if:
•QM- Page Owner entry is the extension (not main attendant), trunk, OPX, ACD/UCD master or Ring
Group number.
Conditions...