Nitsuko Digital System Feature And Terminal Programming Manual

QJ- INTERCOM CALL CONTROL, ALERTS (MESSAGE)
Description
Use this option to allow/deny the Message Waiting reminder message.  Refer to the Message Waiting feature.  If
allowed (N), a voice message periodically plays to remind the user that they have a Message Waiting.  If denied
(Y), the reminder message never plays.  The reminder message is, You have a message.
Conditions 
Voice messages can play only if your system has a 12SCU/VMU Module.
Default Value
Message Waiting reminder message allowed (N)....

QK- CEU IDENTIFICATION
Description
Use this option to enter the System Identification.  The System Identification is four lines long, with up to 17
characters in each line.  It can consist of any combination of characters A-Z and the digits 0-9, # and *.
Conditions 
None
Default Value
No System Identification programmed.
Feature Reference
Automatic Fault Reporting/Remote Maintenance
System Identification
Instructions
To enter data on the PRF:
1. For QK- KSU ID on Table 9, enter the System...

QL- ARS/ACCOUNT CODES, MANDATORY ACCOUNT CODES
Description
Use this option to enable (Y) or disable (N) Mandatory Account Codes system-wide.
Conditions 
None
Default Value
Mandatory Account Codes disabled (N).
Feature Reference
Account Code Capability
Instructions
To enter data on the PRF:
1. For QL- Acct Codes Mandatory on Table 9, enter Y or N.
To enter data at the programming terminal:
1. Type Q.  You see:  Q-CMD>
2. Type L.  You see:  ACCT CODES MANDATORY?
3. Enter Y or N for QL- Acct Codes Mandatory...

QL- ARS/ACCOUNT CODES, VERIFIABLE ACCOUNT CODES
Description
Use this option to enable (Y) or disable (N) Verifiable Account Codes system-wide.
Conditions 
None
Default Value
Verifiable Account Codes disabled (N).
Feature Reference
Account Code Capability
Instructions
To enter data on the PRF:
1. For QL- Verify Codes on Table 9, enter Y or N.
To enter data at the programming terminal:
1. After entering Y for QL- Mandatory Account Codes, you see: VERIFY CODES?
2. Enter Y or N for QL- Verify Codes from...

QL- ARS/ACCOUNT CODES, ACCT CODES FOR TOLL CALLS ONLY
Description
Use this option to enforce Account Codes for all trunk calls (N) or for just toll (1+) trunk calls (Y).
Conditions 
None
Default Value
Account codes enabled for all trunk calls (N).
Feature Reference
Account Code Capability
Instructions
To enter data on the PRF:
1. For QL- Acct Codes for Toll Call Only on Table 9, enter Y or N.
To enter data at the programming terminal:
1. After entering data for QL- Verifiable Account Codes, you see: ACCT...

QL- ARS/ACCOUNT CODES, MIN. COS FOR ACCOUNT CODES
Description
Use this option to set the minimum COS number that requires Mandatory Account Code entry.  For example, en-
tering 15 requires COSs 15-27 to enter Account Codes.  COSs 00-14 do not have to enter Account Codes.  To
force all extension users to enter Account Codes (including attendants), enter 00.
Conditions 
None
Default Value
Only COS 27 must enter an Account Code (27).
Feature Reference
Account Code Capability
Instructions
To enter data on...

QL- ARS/ACCOUNT CODES, ARS ENABLE (HYBRID ONLY)
Description
Use this option to enable ARS.  The choices are:
0 ARS not enabled
2 ARS enabled
1
This option is not available on key systems.
Conditions 
None
Default Value
ARS disabled (0).
Feature Reference
Automatic Route Selection
Instructions
To enter data on the PRF:
1. For QL- ARS on Table 9, enter 0, 1 or 2.
To enter data at the programming terminal:
1. After programming QL- Minimum COS for Mandatory Account Codes or entering N for QL- Mandatory...

QL- ARS/ACCOUNT CODES, NUMBER OF SERVICES
Description
Use this option to designate how many services (trunk rotaries) ARS will use.1  The choices are 01-10.  This
prompt appears only if you enter 1 or 2 for the QL- ARS ENABLE option.
This option does not apply to key systems.
Conditions 
None
Default Value
No services designated (00).
Feature Reference
Automatic Route Selection
Instructions
To enter data on the PRF:
1. For QL- No. of Services (01-10) on Table 9, enter the number of services (trunk...

QL- ARS/ACCOUNT CODES, SERVICE LINE NUMBERS
Description
Use this option to assign the trunk rotary master number for each of the rotaries used by ARS.  Service number
01 should be the DDD trunk group.  This entry should correspond to the EA- First Trunk in Group entry.
If you are programming ARS
1, this is the last QL option you have to program. 
This option does not apply to key systems.
Conditions 
None
Default Value
No rotaries assigned (00).
Feature Reference
Automatic Route Selection
Instructions
To...

QM- MUSIC/RELAY CONTROL, BGM
Description
Enter Y to enable Background Music; N to disable.  Refer to the system Hardware Manual for additional installa-
tion details.
Conditions 
Background Music uses the fourth trunk circuit on the first CO Module in the main CEU.  Although you con-
nect to the CEU MOH terminals, you cannot use the fourth trunk circuit for trunks.  Refer to the system Hard-
ware Manual for additional installation details.
Default Value
No trunk assigned (00).
Feature Reference...