Nitsuko Digital System Feature And Terminal Programming Manual

- For Your Notes -
J- COMMUNICATIONS PORT PARAMETERS
PORT SPEED
434   PROGRAMMING N1870SWG04   Issue 1-0 

K- PROGRAMMABLE KEY DATA, KEYSETS AND DSS CONSOLESKD- PROGRAMMING KEYS FOR DSS CONSOLES
Description
Use this option to assign consoles to keysets, assign blocks (key configurations) to consoles and program con-
sole key functions.
Assigning Consoles to Keysets
You can assign a DSS Console to any keyset.  You can assign as many DSS Consoles as there are available dual
ports.  Four consoles can have unique programming.  See Assigning Blocks below.
Assigning Blocks (Key Configurations) to DSS Consoles
The...

Instructions
To enter data on the PRF:
1. For each DSS Console, on Table 7 indicate:

The DSS Owner

The DSS block (configuration) number

The DSS key definitions
To enter data at the programming terminal:
Before programming DSS Consoles, make sure the console has circuit type 06.
1. Type K.  You see:  K-CMD
2. Type D.  You see:  DSS EXT?
3. Enter the extension number of the DSS Console you want to program.  You see:  DSS OWNER?
4. Enter the extension number of the keyset assigned to the DSS Console....

To copy the KD programming from another console:
This helps if you have consoles with similar or identical KD programming.
1. Using KD, go to the beginning of the configuration you want to copy.
2. Type C.  You see:  COPY FROM WHICH DSS EXT #
3. Enter the number of the console from which you want to copy. You see:  FROM KEY # (01-80)
4. Enter the key number (on the other console) where you want to begin copying.  This entry does not have
to correspond to the key you are on.  You see:  TO KEY # (01-80)
5....

KL- LISTING PROGRAMMABLE KEY DATA
Description
Use this option to list the keyset and DSS Console key programming.  The system lists the keyset key program-
ming before the DSS Console key programming.
Sample Keyset Listing
KEYSET EXT # 300 
KEY #01 - LINE 801
KEY #02 - LINE 802
KEY #03 - LINE 803
KEY #04 - LINE 804
      through
KEY #24 - LINE 824
Sample DSS Console Listing
DSS EXT 302
DSS OWNER: 304
KEY #01 - HOTLINE TO EXT 304
KEY #02 - HOTLINE TO EXT 305
       through
KEY #80 - RELEASE
Conditions...

KS- PROGRAMMING KEYS FOR KEYSETS
Description
Use this option to assign a function to each keyset programmable key.  The chart below shows the options, the data
you enter and the related feature.  Remember, each keyset should have at least one switched or fixed loop key.
For this option... Enter this data.. Refer to this feature
Group Pickup G + Grp # (01-23) Group Call Pickup
Page P + Zone # (0-7) Paging
Record R Voice Mail Compatibility
Station Pickup S + Ext # Call Coverage Keys
Feature F + Line # +...

Central Office Calls, Placing
Centrex Compatible Feature Keys
Direct Inward Line (DIL)
Digital Door Box
Group Call Pickup 
1
Hotline
Loop Keys
Message Center
Paging 
1
Prime Line Selection
Privacy Release Groups
Private Line
Programmable Keys
Ringing Line Preference
Speed Dial
 1
Split
Telemarketing Dial
Tenant Service
Voice Mail Compatibility (Integrated Voice Messaging)
Voice Module Unit (VMU)
Instructions
To enter data on the PRF:
1. For each keyset, on Table 6 enter:
•F in the Entry Identifier...

To enter data at the programming terminal:
1. Type K.  You see:  K-CMD>
2. Type S.  You see:  KEYSET EXT # 300 -
3.
-Enter the number of the keyset you want to program and press RETURN.
OR
-Press RETURN to program the next consecutive extension 300 (starting with 300).
4. You see:  KEY #01 -
5.
-Type K, the key number you want to program (01-24) and press RETURN,
OR
-Press RETURN to program the next consecutive key (starting with key 01).
6. Enter the data for the key you select from Table 6 and press...

To copy (mark) the KS programming from an extension:
This helps if you have extensions with similar or identical KS programming.
1. Using KS, go to the beginning of the key configuration you want to copy.
2. Type C.  You see:  KEYS TO COPY?.
3.
-Type in the number of keys you want to copy (e.g., 04), starting with the key you are programming.
To clear the copy buffer, type 00.  The copy buffer also clears when you exit the KS command.
-Press RETURN.  You see:  COPY UNDEFINED KEYS? [Y/N]
4.
-Type Y to...

L- LISTING SYSTEM AND EXTENSION DATALE- LISTING DATA BY EXTENSION/TRUNK
Description
Use LE- Listing Data by Extension/Trunk to list the programmed options for each extension and trunk.  The re-
port is in extension/trunk number order.  There are three parts to the report:
•Programmed options for extensions (without ED)
•Programmed options for trunks (without ED)
•ED programming for extensions, OPX and DISA trunks
Below are samples of each of the three reports.
Sample Extension/Trunk Listing (Without ED)...