Nikon Coolpix S7 Users Manual

							137
For Connection via Home Wireless LAN
Wireless Transfer Mode
5Start the Setup Utility.
For the initial installation run, the Setup Utility will launch automatically when
installation is complete.
From the second time, start the Setup Utility by following the procedure below:
Windows: Start the computer and select [Start] > [All programs] > [Wireless
Camera Setup Utility] > [Wireless Camera Setup Utility].
Macintosh: Start the computer and open [Applications] > [Nikon Software] >
[Wireless Camera Setup Utility] folder. Then double-click the [NkWire-
lessSetup] icon.
• Click [Next] after checking the contents shown in
the screen at right.
6Choose the action [Add profiles].
7Choose the profile type [Add Profile at
Home Wireless LAN]. 
You can start configuration of infrastructure mode or
ad-hoc mode for the computer connected to the wire-
less LAN.
Set up for Public Wireless LAN is available only for
T-Mobile HotSpot in United States.
Downloaded From camera-usermanual.com Nikon Manuals 
						

							138
For Connection via Home Wireless LAN
Wireless Transfer Mode
8Choose the connection method.
Available profile types (see the list below) for your
wireless LAN will be displayed on screen. Select the
desired profile type and click [Next].
When selecting [Create an Ad-hoc (Camera to Com-
puter) network profile], proceed to step 11 (c139).
If multiple wireless LAN devices are connected to the
computer, choose a device from the pop-up menu.
Select the desired configuration type from the options
listed. Options displayed will differ depending on the
selected wireless device.
jNote on Choosing [Create an Ad-hoc (Camera to Computer) network 
profile] on Windows XP
• When configuring a profile device using an ad-hoc network between the camera and com-
puter, the computer’s fixed IP address (manually entered IP address) will be automatically
set to “169.254.x.x”. When adding an infrastructure network later, set the computer to
automatically obtain an IP address. For the added network profiles, configure wireless set-
tings between the camera and computer again. 
• [Create an Ad-hoc (Camera to Computer) network profile] cannot be selected if an infra-
structure network has already been set up in your computer, or the fixed IP address is not
“169.254.x.x”.
Type of ProfileDescriptions
Infrastructure (Access Point) 
network profileFor use when connecting the camera and com-
puter via an infrastructure network. An infrastruc-
ture network must be configured beforehand.
Ad-hoc (Camera to Computer) 
network profileFor use when establishing a one-to-one connec-
tion (when a wireless LAN access point is not avail-
able) between the camera and computer.
Infrastructure (Access Point) 
and Ad-hoc (Camera to Com-
puter) network profilesRecommended for users of multiple wireless net-
work profiles.
Create Profile manuallyFor use with manual settings. Only [Create Profile 
manually] is available when:
- configuration for wireless LAN network is not 
performed using the wireless network setting 
function (Zero Config) for Windows XP
- using a Windows XP SP1 or Mac OS X operating 
system
- your computer has a fixed IP address
Downloaded From camera-usermanual.com Nikon Manuals 
						

							139
For Connection via Home Wireless LAN
Wireless Transfer Mode
9Enter network settings.
Enter the settings for connecting the camera and com-
puter via a wireless network.
When selecting [Create an Infrastructure (Access
Point) network profile] or [Create Infrastructure
(Access Point) and Ad-hoc (Camera to Computer) net-
work profiles] in step 8, select a network name from
the [Network Name (SSID)] list. This name will be used
when connecting the camera and computer.
When selecting [Create Profile manually] in step 8,
manually enter the same values set in the computer for all items except those that
are automatically provided. See “Settings for the Setup Utility” for reference
(c141). 
When settings are complete, click [Next]. 
10Configure TCP/IP.
When selecting [Create Profile manually] in step 8, or
if the screen in step 8 does not appear, manually enter
the address type and IP address, referring to those
used in “Settings for the Setup Utility” (c141). 
When settings are complete, click [Next].
11Set profile name and icon.
Enter a profile name (up to 16 single-byte alphanu-
meric characters).
The entered profile name will appear in the selection
list for the profile device (c144). We recommend
selecting a name that will let you easily tell devices
apart, such as “Desktop-Home”.
When settings are complete, click [Next]. 
Downloaded From camera-usermanual.com Nikon Manuals 
						

							140
For Connection via Home Wireless LAN
Wireless Transfer Mode
12Configure wireless printing.
If a printer is connected to the computer, check [Cre-
ate Wireless Printing Profile] and select the printer to
be used for wireless printing (c158).
Enter a profile name (up to 16 single-byte alphanu-
meric characters), select a printer, and click [Next].
If no printers are connected to the computer, click
[Next] without selecting a printer.
13Configure COOLPIX CONNECT. 
If using COOLPIX CONNECT, enter the profile name for COOLPIX CONNECT.
• Check [Create a COOLPIX CONNECT Profile] and
enter a profile name (up to 16 single byte alphanu-
merical characters) and click [Next].
14Settings are complete. 
Select [Finish wizard] and click [Next]. 
15Disconnect the computer and camera. 
Turn off the camera before removing it from the COOL-STATION.
Downloaded From camera-usermanual.com Nikon Manuals 
						

							141
For Connection via Home Wireless LAN
Wireless Transfer Mode
Settings for the Setup Utility 
When configuring a profile using the Setup Utility, refer to the description for
each item listed below. Settings are the same for Windows and Macintosh.
* Mandatory items
SettingsDescriptions
Network name 
(SSID)*Enter the network ID for the computer. Choose a value dis-
played. If multiple values are displayed, select one.
Network type*Select [Ad-hoc] or [Infrastructure]. The camera and computer 
must be set to the same configuration.
• Ad-hoc mode: This mode establishes a peer-to-peer (one-to-
one) connection between the camera and computer.
• Infrastructure mode: This mode connects the camera and 
computer via a wireless LAN access point.
ChannelMandatory if [Ad-hoc] is selected for [Network type]. Select the 
same channel (1 to 11) set in the computer.
AuthenticationSelect [Open System], [Shared Key], [WPA-PSK]* or [WPA2-
PSK]* (* [Infrastructure] only). Select the same method set in 
the computer or access point.
EncryptionAvailable methods for the camera differ depending on the 
selected authentication method (see below). Select the same 
method set in the computer or access point.
Encryption keyEnter the security key set in the computer or access point 
(unnecessary when [Encryption] is set to [None]).
Key indexWhen [Encryption] is set to [WEP], and infrastructure mode is 
used, select the same key index set in the computer or access 
point (unnecessary when [Encryption] is set to [None], [TKIP] or 
[AES]). The default setting is [1].
Selected authentica-
tion methodAvailable security method(s) for 
the camera
[Open System] [None], [WEP]
[Shared Key] [WEP]
[WPA-PSK] [TKIP]
[WPA2-PSK] [AES]
Downloaded From camera-usermanual.com Nikon Manuals 
						

							142
For Connection via Home Wireless LAN
Wireless Transfer Mode
jWireless LAN Channels
Wireless LAN channels for the COOLPIX S7c are from 1 to 11. Make sure that the channel for
your computer’s wireless LAN device is set to a channel between 1 and 11 (inclusive).
jMAC Address Filtering
When MAC address filtering is enabled, only devices with an authorized MAC address can
access the wireless LAN. Check the camera’s MAC address in [Firmware Version] of the setup
menu (c129) and add it to the authorized list.
jPort Number
For wireless communication, the UDP port number is “5353” and the TCP port number is
“15740”. If the computer or access point has a firewall, the firewall settings may need to be
changed.
lNotes on Profile Devices
• Configure profiles for each computer using the Setup Utility and install the Setup Utility to
each computer to transfer (receive) pictures from the camera remotely. 
• You can configure a maximum of nine profile devices (computers, printers connected to a
computer, the optional PD-10 wireless printer adapter, etc.) in the camera. If nine have
already been configured and you want to add a new one, delete an unneeded profile
device using the Setup Utility.
• Start the Setup Utility while the camera is connected to a computer via USB cable, and you
can rename or delete profiles. Choose [Rename/Delete profiles] in the action selection
screen of the Setup Utility and click [Next]. Then choose a profile you wish to rename or
delete and click [Rename] or [Delete]. You can also confirm the details of a profile by click-
ing [View Profile]. Choose [Reset camera] in the action selection screen to delete all profiles
(all address book contents are also deleted).
Configure*Select [Auto] (default setting) or [Manual] for the method of 
setting the camera IP address.
IP AddressWhen [Configure] is set to [Manual], enter the IP address for 
the camera.
SettingsDescriptions
Downloaded From camera-usermanual.com Nikon Manuals 
						

							143
Wireless Transfer Mode
Transferring Pictures
Establishing a Wireless Connection
1Enter wireless transfer mode by pressing
D in shooting mode, selecting n (use
the rotary multi selector), and then
pressing d.
The wireless LAN start-up screen will be displayed and
the camera will search for available SSIDs.
2Choose the SSID and press d.
The SSIDs are listed in order of radio field strength.
Wireless connection has not yet been established.
The left icon of each SSID is indicated in red when
outside the network area.
The right icon indicates the type of the profile regis-
tered to each SSID:
Z (profiles with home wireless LAN information), 
-- (profiles with no information)
Connection is attempted with the selected network (SSID) when picture transfer is
attempted.
3Choose the desired transfer or printing
method and press d.
When selecting [COOLPIX CONNECT], see “Upload-
ing Pictures to COOLPIX CONNECT” (c145).
When selecting [Wireless Printing], see “Printing Pic-
tures (Wireless Printing)” (c158).
When selecting other options, see “Transferring Pic-
tures to a Computer (PC Connection)” (c149).
If no operations are performed about three minutes, auto power off will take
effect and the monitor turns off. Although auto power off will also take effect
during wireless transfer mode, transfer will continue.
Wireless LAN
Cancel Searching for SSID
Select SSID
My Network
HOTSPOT
Function selection menuCOOLPIX CONNECT
Easy Transfer (PM)
Easy Trans. (no PM)
Shooting date
Selected Images
Downloaded From camera-usermanual.com Nikon Manuals 
						

							144
Transferring Pictures
Wireless Transfer Mode
When Transfer is Complete
The message shown at right is displayed when the
transfer is complete.
• To repeat the transfer, press d. 
• To exit wireless transfer mode, press D and
choose another mode, or turn off the camera.
kWireless Transfer LEDThe wireless transfer LED (c6) is located on the side of the camera (inside the antenna). The
camera is searching for profiles when the LED blinks, a wireless connection is established
when the LED is lit, and the camera is disconnected from a wireless LAN when the LED is off.
If transfer is not performed for a while, the LED may blink to save power.
kNote on Wireless Transfer ModeThe camera strap eyelet may become hot during wireless communication (i.e., when the wire-
less transfer LED is lit or is blinking). Observe due caution when handling the camera.
kThe Memory Card Write-Protect SwitchWhen the memory card write-protect switch is in the “lock” position, transfer cannot be per-
formed. Unlock by sliding the switch to the “write” position before transferring pictures.
kWhen the Transfer is UnsuccessfulWhen transfer is unsuccessful, the next time you attempt
transfer, the confirmation dialog shown at right will be dis-
played. If necessary, you can change profiles from the confir-
mation dialog. Complete transfer, making sure that it was
successful.
kSelecting a Computer or PrinterWhen the selected SSID has multiple computers or printers
registered, the screen shown at right will be displayed after
step 3 (c143). Select the desired computer or printer.
kChecking SSID Contents Pressing the zoom control to v(l) in the SSID selection screen
displays the information for the selected profile including the
network name (SSID), type of computer and printer.
Mail sent. Closed
connection to
alias.
Select SSID
Resume interrupted transfer?
No
Change SSIDYe s
Choose profile
Profile-A
Profile-B
Profile-C
SSID: My Network
TYPE: Home SSID
Profile:
Profile-A
Downloaded From camera-usermanual.com Nikon Manuals 
						

							145
Transferring Pictures
Wireless Transfer Mode
Uploading Pictures to COOLPIX CONNECT
To use COOLPIX CONNECT, perform the following procedures.
1Choose [COOLPIX CONNECT] in step 3 of
“Establishing a Wireless Connection”
(c143) and press d.
2Enter your e-mail address correctly.
Choose [Input] in the sender information entry screen
and press d.
Enter your e-mail correctly in the address screen and
press the shutter-release button. Then enter your
(sender) name for the notification e-mail to recipients
and press the shutter-release button. For information
on how to enter characters, see “Entering Characters
on the Camera” (c148).
Function selection menuCOOLPIX CONNECT
Easy Transfer (PM)
Easy Trans. (no PM)
Shooting date
Selected Images
Enter your alias and
email address
Input
Cancel Enter sender info
Email
Confirm
Back Delete
xxx xxx. xxx@
6411
Downloaded From camera-usermanual.com Nikon Manuals 
						

							146
Transferring Pictures
Wireless Transfer Mode
3Choose [All images] or [Choose date]
and press d.
When choosing [All images], select the desired pic-
tures (up to 30) and press d to mark. Then press the
shutter-release button to apply selection.
When choosing [Choose date], select the shooting
date and press d to mark. Then press the shutter-
release button.
Select the desired pictures (up to 30) and press d to
mark. Then press the shutter-release button to apply
selection.
4Choose the size for the pictures to be
transferred and press the shutter release
button.
Choose the size for the pictures to upload and press
d to mark.
Photoprint1,600 × 1,200 pixels
PC size1,024 × 768 pixels
TV size640 × 480 pixels
All images
Choose date Picture selection
Select image
Confirm
ON/OFFBack
5/30
Choose date
Confirmimages totalON/OFF 10.10.2006 3
2
5
5 09.10.2006
08.10.2006Back
Choose size
Photoprint
PC size
TV size
ConfirmBack
Downloaded From camera-usermanual.com Nikon Manuals