Nikon Camera D810 Users Manual

437
LAN adapters 
(0 261) •
Communication Unit UT-1 : Use a USB cable to connect the 
UT-1 to the camera and an Ethernet cable to connect 
the UT-1 to an Ethernet network .
 Once connected, you 
can upload photos and movies to a computer or ftp 
server, control the camera remotely using optional 
Camera Control Pro 2 software, or browse pictures or 
control the camera remotely from an iPhone or web 
computer browser.
• USB Cable Gaskets and Connector Covers : Use a UF-4 
connector cover for USB cables...

438
Viewfinder 
eyepiece 
accessories•
Rubber Eyecup DK-19 : The DK-19 makes the image in the 
viewfinder easier to see, preventing eye fatigue.
• Diopter-Adjustment Viewfinder Lens DK-17C : To 
accommodate individual differences in vision, 
viewfinder lenses are availabl e with diopters of –3, –2, 
0, +1, and +2 m
–1. Use diopter adjustment lenses only 
if the desired focus can not be achieved with the built-
in diopter adjustment control (–3 to +1 m
–1). Te s t  
diopter adjustment lenses before...

439
Remote 
terminal 
accessoriesThe D810 is equipped with a ten-pin remote terminal 
(
0 3) for remote control and automatic photography.
 The terminal is provided with a cap, which protects the 
contacts when the terminal is not in use. The following 
accessories can be used (all lengths are approximate):
• Remote Cord MC-22/MC-22A : Remote shutter release with 
blue, yellow, and black terminals for connection to a 
remote shutter-triggering device, allowing control via 
sound or electronic signals...

440
Remote 
terminal 
accessories•
GPS Adapter Cord MC-35  (0 233): This 35 cm (1 ft 2 in.) cable 
connects the camera to older GARMIN eTrex- and 
geko-series GPS units that conform to version 2.01 or 
3.01 of the National Marine Electronics Association 
NMEA0183 data format.
 Only models that support PC 
interface cable connections are supported; the MC-35 
can not be used to connect GPS units via USB.
 The 
units connect to the MC-35 using a cable with a D-sub 
9-pin connector provided by the...

441
Wireless 
remote 
controllers 
(0 357) •
Wireless Remote Controller WR-R10/WR-T10 : When a WR-R10 
wireless remote controller is attached to ten-pin 
remote terminal using a WR-A10 adapter, the camera 
can be controlled wirelessly using a WR-T10 wireless 
remote controller.
• Wireless Remote Controller WR-1 : The WR-1 can function as 
either a transmitter or a receiver and is used in 
combination either with another WR-1 or a WR-R10 or 
WR-T10 wireless remote controller.
 For example, a 
WR-1 can be...

442
Attaching a Power Connector and AC Adapter
Turn the camera off before attaching an optional power 
connector and AC adapter.
1Ready the camera.
Open the battery-
chamber (q) and power 
connector ( w) covers.
2Insert the EP-5B power connector.
Be sure to insert the connector in the 
orientation shown, using the 
connector to keep the orange battery 
latch pressed to one side.
 The latch 
locks the connector in place when 
the connector is fully inserted.
3Close the battery-
chamber cover.
Position the...

443
4Connect the EH-5b AC adapter.
Connect the AC adapter power cable to the AC socket on AC 
adapter (e) and the power cable to the DC socket ( r).
 A V  
icon is displayed in the monitor when the camera is powered 
by the AC adapter and power connector. 

444
Storage
When the camera will not be used for an extended period, 
remove the battery and store it in a cool, dry area with the 
terminal cover in place.
 To prevent mold or mildew, store the 
camera in a dry, well-ventilated area.
 Do not store your camera 
with naphtha or camphor moth balls or in locations that:
• are poorly ventilated or subject to humidities of over 60%
• are next to equipment that pr oduces strong electromagnetic 
fields, such as televisions or radios
• are exposed to...

445
Image Sensor Cleaning
If you suspect that dirt or dust on the image sensor is appearing 
in photographs, you can clean the sensor using the Clean image 
sensor  option in the setup menu.
 The sensor can be cleaned at 
any time using the  Clean now option, or cleaning can be 
performed automatically when the camera is turned on or off.
❚❚ “Clean Now”
Holding the camera base down, select 
Clean image sensor  in the setup menu, 
then highlight  Clean now and press J.
 
The camera will check the image...

446
❚❚“Clean at Startup/Shutdown”
Choose from the following options:
1Select  Clean at startup/shutdown .
Display the  Clean image sensor  
menu as described on page 445.
 
Highlight  Clean at startup/
shutdown  and press 2.
2Select an option.
Highlight an option and press  J.
OptionDescription
5Clean at startup The image sensor is automatically cleaned each 
time the camera is turned on.
6Clean at 
shutdownThe image sensor is automatically cleaned 
during shutdown each time the camera is turned 
off....