Nikon Camera D3300 Reference Manual

131
P, S, A, and M Modes
5
Measure white balance.
Before the indicators stop flashing, 
frame the reference object so that it 
fills the viewfinder and press the 
shutter-release button all the way down.
 No photograph will 
be recorded; white balance can be measured accurately even 
when the camera is not in focus.
6
Check the results.
If the camera was able to measure a 
value for white balance, the message 
shown at right will be displayed and 
a  will flash in the viewfinder for 
about eight seconds...

132P, S, A, and M ModesD
Measuring Preset White Balance
If no operations are performed while the displays are flashing, direct 
measurement mode will end in the time selected for the  Auto off 
timers  option in the setup menu ( 0245).
 The default setting is eight 
seconds.
DPreset White Balance
The camera can store only one value for preset white balance at a time; 
the existing value will be replaced when a new value is measured.
 
N o te  t h a t  ex p o s u re i s  a u to m a t i c a l l y  i n c...

133
P, S, A, and M Modes
❚❚ Copying White Balance from a PhotographFollow the steps below to copy a value for white balance from a 
photograph on the memory card.1
Select  Preset manual .
To display the menus, press the  G 
button.
 Highlight  White balance  in 
the shooting menu and press  2 to 
display white balance options.
 
Highlight  Preset manual  and press 
2 .
2
Select  Use photo .
Highlight  Use photo  and 
press  2.
3
Choose  Select image .
Highlight  Select image  and 
press  2 (to skip the...

134P, S, A, and M Modes
4
Choose a folder.
Highlight the folder 
containing the source 
image and press  2.
5
Highlight the source 
image.
To view the highlighted 
image full frame, press and 
hold the  X button.
6
Copy white balance.
Press  J to set preset white balance to 
the white balance value for the 
highlighted photograph. 

135
P, S, A, and M Modes
Nikon’s unique Picture Control system makes it possible to share 
image processing settings, including sharpening, contrast, 
brightness, saturation, and hue,
 among compatible devices and 
software.
Selecting a Picture ControlChoose a Picture Control according to the subject or type of 
scene.Picture Controls
Option
Description
Q Standard Recommended for most situations, this option uses 
standard processing for balanced results.
R Neutral A good choice for photographs that...

136P, S, A, and M Modes
1
Display Picture Control options.
Press the  G button to display the 
menus. Highlight  Set Picture Control  
in the shooting menu and press  2.
2
Select a Picture Control.
Highlight a Picture Control 
and press  J.
G  button 

137
P, S, A, and M Modes
Modifying Picture ControlsPicture Controls can be modified to suit the scene or the user’s 
creative intent.
 Choose a balanced combination of settings 
using  Quick adjust , or make manual adju stments to individual 
settings.
1
Select a Picture Control.
Press  G to display the 
menus, then highlight  Set 
Picture Control  in the 
shooting menu and press 
2 . Highlight the desired 
Picture Control and press 2.
2
Adjust settings.
Press  1 or  3 to highlight 
the desired setting...

138P, S, A, and M Modes
3
Save changes and exit.
Press  J.
Picture Controls that have been 
modified from default settings are 
indicated by an asterisk (“*”). 

139
P, S, A, and M Modes
❚❚ Picture Control Settings
Option
Description
Quick adjust Mute or heighten the effect of the selected Picture 
Control (note that this resets all manual adjustments).
 
Not available with 
Neutral or Monochrome  Picture 
Controls.
Manual adjustments (all Picture Controls)Sharpening Control the sharpness of outlines.
 Select 
A to adjust 
sharpening automatically according to the type of 
scene.
Contrast Adjust contrast manually or select 
A to let the camera 
adjust contrast...

140P, S, A, and M ModesD
“A” (Auto)
Results for auto sharpening, cont rast, and saturation vary with 
exposure and the position of the subject in the frame.AThe Picture Control Grid
To display a grid showing saturation (non-
monochrome controls only) and contrast for 
the Picture Control selected in Step 2, press 
and hold the  X button.
The icons for Picture Controls that use auto 
contrast and saturation are displayed in 
green in the Picture Control grid, and lines 
appear parallel to the axes of the...