Nextar Xpj Projector User Manual

Remote control effective range 
 
Infra-Red (IR) remote control sensors are located on the front and the back of the projector. 
The remote control must be held at an angle within 30 d egrees of the projector’s IR remote control sensors to 
function correctly. The distance between the remote c ontrol and the sensors should not exceed 6 meters (~ 
20 feet). 
 
 
Make sure that there are no obstacles between the 
remote control and the IR sensors on the projector 
that might obstruct the infra-red beam....

 12
Connection 
When connecting a signal source to the projector, be sure to: 
1. Turn all equipment off before making any connections; 
2. Use the correct signal cables for each source; and 
3. Ensure that the cables are firmly inserted. 
In the connections shown below, some cables may not be included with the projector (see  Shipping 
Contents on page 6 ). They are commercially available from electronics stores.
 
 
Cable connection 
 
Connecting video source devices 
This section describes how to...

 13
If you have a separate sound system, you will most likely  want to connect the audio output of your video source 
device to that sound system, instead  of to the mono audio projector. 
 
The audio connections illustrated in the following secti ons are provided for informational purposes only. You need 
not connect audio to the projector if there is an alternat e sound system available, or if audio is not required. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

Operation 
Start-up 
1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). 
Check that the Power indicator on our projector ada pter lights orange after power has been applied. 
2. Plug the DC plug into the projector’s 12VDC socket. Re move the lens cap. If it is left on, it could become 
deformed due to the heat produced by the projection lamp. 
3. Switch on the main power at the left side of the proj ector. Check that the Power inductor on the...

 15
Shutdown 
1. Press Power to turn the projector off. 
2. The Power indicator light flashes green and the lamp shuts down. The fans continue to run for 
approximately 45 seconds to cool down the projector. 
λ  To protect the lamp, the projector will not respon d to any commands during the cooling process. 
λ To shorten the cooling time, you can also  activate the Quick Cooling function. 
3. Switch off the main Power at the left side and di sconnect the power cord at the adaptor from the wall 
socket....

Menu operation 
Menu system 
OSD MENU1  
 
Video 
S-Vide 
 
 
Dynamic 
Static 
Theater 
Game 
 
Front/Up 
Front/Down 
Rear/Up 
Rear/Down 
OSD Menu 2  
 
0 to 100 Brightness (Default 50) 
 
0 to 100 Contrast (Default 50) 
 16 

 
0 to 100 Color (Default 50) 
OSD Menu 3  
 
0 to 100 Hue (Default 50) 
 
 
English 
French 
German 
Spanish 
Portuguese 
Italian 
 
 
System Default 
 
 
 
 
 
 
 
 
 
 
 
 
 17 

Picture menus 
Some picture adjustments are available only when certain input sources are in use.   
FUNCTION 
(Default setting 
/ Value) 
 
DESCRIPTION 
 
Source Input 1. Video Input: RCA composite video 
2. S-Video Input: Mini DIN5 S-Video 
 
Video Mode 1. Dynamic (Default): Is suitable for enjoying colorful movies and TV in a blackened  
living room lighting level environment. 
2. Static Mode: Is suitable for enjoying  DVD movies and TV best viewed in a darkened 
(not bright) lounge room environment....

 19
Hue Adjusts the color tones of the image. The higher the value, the more greenish the 
image becomes. The lower the value, the more reddish the image becomes. 
Language Language sets the language for the OSD control menus. 
Use Left  / Right  on the projector 　　 , or Left  / Right  on the remote　　  control, to 
select your desired language. 
Default Returns all settings to the factory preset values.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

 20
Troubleshooting 
THE PROJECTOR DOES NOT TURN ON. 
Cause Remedy 
There is no power from the power cable. 
 
Plug the power cord into the AC inlet on the projector, 
and plug the power cord from the power outlet. If the 
power outlet has a switch, make sure that it is switched 
on.
 
Attempting to turn the projector on again during the 
cooling process.
 
Wait until the cooling down process has completed. 
 
 NO PICTURE.  
Cause Remedy 
The video source is not turned on or connected 
correctly.
 
Turn...