Netgear Prosafe 8 Port Manual

							Use VLANS for Traffic Segmentation 51
 ProSAFE 8-Port and 16-Port Gigabit Click Switch
2. 
Use an Ethernet cable to connect your computer to an Ethernet port on th\
e switch.
3.  Launch a web browser
 .
4.  In the address field of the browser
 , enter the IP address of the switch.
You can find the IP address of the switch by using the ProSAFE Plus utili\
ty or get it from  the DHCP server
 . If the switch cannot get an IP address from a DHCP server, enter 
192.168.0.239.
You are asked to enter the password for the switch.
5.  Enter the switch’
 s password in the password field.
The switch’s default password is password.
The Switch Information screen displays.
6.  Select  VLAN > 802.1Q > 
 Advanced > VLAN Membership.
7. Select the ports.
8.  Select  T
 agging Control or  UnTag Tagging Control .
9.  Click the  Apply button
Your settings are saved. 
						

							52
6
6.   Manage the Switch
This chapter covers the following topics: 
•Use the ProSAFE Utility to View Switch Status
•View Switch Information
•Enable Loop Detection
•Upgrade the Firmware
•Reboot the Switch
•Save the Switch Configuration
•Restore a Saved Switch Configuration
•Restore Factory Default Settings
•Enable Port Mirroring 
						

							Manage the Switch 53
 ProSAFE 8-Port and 16-Port Gigabit Click Switch
Use the ProSAFE Utility to View Switch Status
To view the switch status:
1. 
Connect your computer to the same network as the switch.
You can use a WiFi or wired connection.
2.  Double-click the  ProSAFE Plus Utility icon.
The configuration home screen displays a list of Plus switches that it d\
iscovers on the  local network.
3.  Select a switch.
If you do not see the switch, click the REFRESH button.
4.  Click the  APPL
 Y button.
You are asked to enter the password for the switch.
5.  Enter the switch’
 s password in the password field.
The switch’s default password is password.
View Switch Information
You can view the switch product name (model), MAC address, firmware lev\
el, DHCP mode,  and other network information.
Use the ProSAFE Utility to View Switch Information
To view information about the switch:
1.  Connect your computer to the same network as the switch.
You can use a WiFi or wired connection. 
						

							Manage the Switch 54
ProSAFE 8-Port and 16-Port Gigabit Click Switch 
2. 
Double-click the  ProSAFE Plus Utility icon.
The configuration home screen displays a list of Plus switches that it d\
iscovers on the  local network.
3.  Select a switch.
If you do not see the switch, click the REFRESH button.
4.  Click the  APPL
 Y button.
You are asked to enter the password for the switch.
5.  Enter the switch’
 s password in the password field.
The switch’s default password is  password.
The Switch Status screen displays.
6.  Select  Switch Information.
Use Browser-Based Access to View Switch Information
To view information about the switch:
1. Set up your computer to use an IP address in the same subnet as the IP a\
ddress of the 
switch.
2.  Use an Ethernet cable to connect your computer to an Ethernet port on th\
e switch.
3.  Launch a web browser
 .
4.  In the address field of the browser
 , enter the IP address of the switch.
You can find the IP address of the switch by using the ProSAFE Plus utili\
ty or get it from  the DHCP server
 . If the switch cannot get an IP address from a DHCP server, enter 
192.168.0.239.
You are asked to enter the password for the switch.
5.  Enter the switch’
 s password in the password field. 
						

							Manage the Switch 55
 ProSAFE 8-Port and 16-Port Gigabit Click Switch
The switch’s default password is password.
The Switch Information screen automatically displays. 
Note:
To navigate to this screen, select System > Management > Switch 
Information.
Control the Switch LEDs
By default, the switch’s Link Speed and Activity LEDs light when the port is in use. You can 
turn off the switch LEDs or you can turn on only the Link Speed LEDs.
Use the ProSafe Utility to Control the Switch LEDs
To control the switch LEDs:
1. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection.
2.  Double-click the  ProSAFE Plus Utility icon.
The configuration home screen displays a list of Plus switches that it d\
iscovers on the  local network.
3.  Select a switch.
If you do not see the switch, click the REFRESH button.
4.  Click the  APPL
 Y button.
You are asked to enter the password for the switch.
5.  Enter the switch’
 s password in the password field.
The switch’s default password is password.
The Switch Status screen displays. 
						

							Manage the Switch 56
ProSAFE 8-Port and 16-Port Gigabit Click Switch 
6. 
Select  System > Management > Port LED Control.
7. Select a radio button.
8.  Click the  APPL
 Y button.
Your settings are saved.
Use Browser-Based Access to Control the Switch LEDs
To control the switch LEDs:
1.  Set up your computer to use an IP address in the same subnet as the IP a\
ddress of the 
switch.
2.  Use an Ethernet cable to connect your computer to an Ethernet port on th\
e switch.
3.  Launch a web browser
 .
4.  In the address field of the browser
 , enter the IP address of the switch.
You can find the IP address of the switch by using the ProSAFE Plus utili\
ty or get it from  the DHCP server
 . If the switch cannot get an IP address from a DHCP server, enter 
192.168.0.239.
You are asked to enter the password for the switch.
5.  Enter the switch’
 s password in the password field.
The switch’s default password is  password.
The Switch Information screen displays.
6.  Select  System > Management >Port LED Control .
7. Select a radio button.
8.  Click the  APPL
 Y button.
Your settings are saved. 
						

							Manage the Switch 
57  ProSAFE 8-Port and 16-Port Gigabit Click Switch
Enable Loop Detection
Loop detection is indicated on the switch when both LEDs of a port blink at a constant speed.
Use the ProSafe Utility to Enable Loop Detection
To enable loop detection:
1. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection.
2. Double-click the ProSAFE Plus Utility icon.
The configuration home screen displays a list of Plus switches that it discovers on the 
local network.
3. Select a switch.
If you do not see the switch, click the REFRESH button.
4. Click the APPLY button.
You are asked to enter the password for the switch.
5. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Status screen displays.
6. Select System > Management > Loop Detection.
The Loop Detection screen displays.
7. Select the Enable radio button.
8. Click the APPLY button.
Your settings are saved.
Use Browser-Based Access to Enable Loop Detection
To enable loop detection:
1. Set up your computer to use an IP address in the same subnet as the IP address of the 
switch.
2. Use an Ethernet cable to connect your computer to an Ethernet port on the switch.
3. Launch a web browser.
4. In the address field of the browser, enter the IP address of the switch.
You can find the IP address of the switch by using the ProSAFE Plus utility or get it from 
the DHCP server. If the switch cannot get an IP address from a DHCP server, enter 
192.168.0.239. 
						

							Manage the Switch 
58 ProSAFE 8-Port and 16-Port Gigabit Click Switch 
You are asked to enter the password for the switch.
5. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information screen displays.
6. Select System > Management > Loop Detection.
The Loop Detection screen displays.
7. Select the Enable radio button.
8. Click the Apply button.
Your settings are saved.
Upgrade the Firmware
Read the new firmware release notes to find out if you need to reconfigure the switch after 
upgrading.
Use the ProSAFE Utility to Upgrade the Firmware
To upgrade the firmware:
1. Download the new firmware from the NETGEAR support website.
2. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection.
3. Double-click the ProSAFE Plus Utility icon.
The configuration home screen displays a list of Plus switches that it discovers on the 
local network.
4. Select a switch.
If you do not see the switch, click the REFRESH button.
5. Click the APPLY button.
You are asked to enter the password for the switch.
6. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Status screen displays.
7. If the firmware release notice specifies that you need to reconfigure the switch, save the 
switch configuration settings.
For more information about how to save the switch configuration, see Save the Switch 
Configuration on page 62. 
						

							Manage the Switch 
59  ProSAFE 8-Port and 16-Port Gigabit Click Switch
8. Select Maintenance > Firmware Upgrade.
The Firmware Upgrade screen displays.
9. Click the BROWSE button and locate and select the firmware file.
10. Click the APPLY button.
WARNING:
To avoid the risk of corrupting the firmware, do not interrupt the 
upgrade. For example, do not turn off the switch or disconnect it.
When the upgrade is complete, your switch restarts. The upgrade process typically takes 
about two minutes.
Use Browser-Based Access to Upgrade the GSS116E Firmware
To upgrade the firmware:
1. Set up your computer to use an IP address in the same subnet as the IP address of the 
switch.
2. Use an Ethernet cable to connect your computer to an Ethernet port on the switch.
3. Launch a web browser.
4. In the address field of the browser, enter the IP address of the switch.
You can find the IP address of the switch by using the ProSAFE Plus utility or get it from 
the DHCP server. If the switch cannot get an IP address from a DHCP server, enter 
192.168.0.239.
You are asked to enter the password for the switch.
5. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information screen displays.
6. Select System > Maintenance > Firmware Upgrade.
The Firmware Upgrade screen displays.
7. Click the Enter Loader Mode button.
The switch reboots and enters into the loader. The Firmware Upgrade screen adjusts.
8. Click the Browse button to select the image file.
9. Click the Apply button.
The switch gets the new firmware from the host and performs the upgrade. 
10. After the upgrade completes, wait a few minutes and then reboot the switch. 
						

							Manage the Switch 
60 ProSAFE 8-Port and 16-Port Gigabit Click Switch 
Use Browser-Based Access to Upgrade the GSS108E Firmware
To upgrade the firmware:
1. Set up your computer to use an IP address in the same subnet as the IP address of the 
switch.
2. Use an Ethernet cable to connect your computer to an Ethernet port on the switch.
3. Launch a web browser.
4. In the address field of the browser, enter the IP address of the switch.
You can find the IP address of the switch by using the ProSAFE Plus utility or get it from 
the DHCP server. If the switch cannot get an IP address from a DHCP server, enter 
192.168.0.239.
You are asked to enter the password for the switch.
5. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information screen displays.
6. Select System > Maintenance > Firmware Upgrade.
The Firmware Upgrade screen displays.
7. Click the Enter Loader Mode button.
The switch reboots and enters into the loader. The Firmware Upgrade screen adjusts.
8. Complete the TFTP Server IP address field.
9. Complete the Image File Name field.
Note:Make sure that the TFTP server launches the TFTP server application.
10. Click the Apply button.
The switch gets the new firmware from the TFTP server and performs the upgrade. 
11. After the upgrade completes, wait a few minutes and then reboot the switch.
Reboot the Switch
You can reboot the switch remotely.
Use the ProSAFE Utility to Reboot the Switch
To reboot the switch:
1. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection.