NEC Xen Alpha Installation Manual

							Installation Manual  •  •  •  Installing DTB Type Multiline MonitorsPage 59
A6-506000-642-01
Xen AlphaRelease 1.0
SECTION 1
GENERAL
INFORMATION
The Xen Alpha system provides a choice of two different DTB-Type Multiline telephones.
This chapter describes each terminal and provides applicable installation instructions.
SECTION 2
MULTILINE
TERMINALS
DTB-16-1A (WH)/(BK) TEL
This digital non-display Multiline Terminal is equipped with eight programmable line keys
(each with a two-colour LED), a built-in speakerphone, headset jack, a large LED to indicate
incoming calls and messages, and compatibility with ADA-UA, APR-UA, CTA-UA, and HFU-
UA Units.
A maximum of 119 DTU-8-1 (WH) TELs can be installed in the Xen Master system and a
maximum of 31 in the Xen Axis system.
Figure 3-1: DTB-16-1A (WH)/(BK) TEL Multiline Telephone
CHAPTER 
3Installing DTB-Type Multiline 
Te r m i n a l s 
						

							Page  60Installing DTB Type Multiline Monitors  •  •  •  Installation Manual
A6-506000-642-01
DTB-16D-1A (WH)/(BK) TEL
This digital Multiline Terminal has eight programmable line keys (each with the two-colour
LED), four softkeys, a built-in speakerphone, headset jack, a Large LED to indicate
incoming calls and messages, and compatibility with ADA-UA, APR-UA, CTA-UA and HFU-
UA Units.
This terminal is also equipped with a 3-line, 24-character, adjustable Liquid Crystal
Display (LCD).
Figure 3-2: DTB-16D-1A (WH)/(BK) TEL Multiline Telephone 
						

							Installation Manual  •  •  •  Installing DTB Type Multiline MonitorsPage 61A6-506000-642-01
SECTION 3
WALL MOUNTINGThe DTB-16-1A (BK)/(WH) TEL and DTB-16D-A1 (BK)/(WH) TEL can be mounted to a wall.
1. Locate the stoppers under the height adjustment stand on the bottom of the telephone.
You will need to lift the adjustment stand to expose the foot stand holding the stoppers.
Remove the two plastic stoppers from the foot stand by firmly pushing on them. 
2. Remove the hanger (located on the bottom of the telephone). Insert the hanger into the
holes as indicated in the above diagram.
3. Use the wall mounting template (provided) to mark the screw positions on the wall. 
						

							Page  62Installing DTB Type Multiline Monitors  •  •  •  Installation Manual
A6-506000-642-01
4. Insert one end of the telephone line cord into the RJ-11 jack. Route the cord inside the
height adjustment stand as indicated in the diagram. The cord can be wrapped more
than once inside the height adjustment stand to shorten the length of cord. The cord
can exit either the top of the telephone or the side, depending on the most convenient
location of the RJ-11 wall jack.
5. Using a philips head screwdriver, insert the flat head wood screw (provided) into the
stopper and fasten to the wall.
6. to hand the telephone on the wall, place the grooves (located on the bottom of the
telephone) over the plastic stopper, which has been fastened tot he wall. If the
telephone is difficult to mount, you may want to loosen the screws holding the stopper.
7. Insert the other end of the telephone line cord into an RJ-11 jack. 
						

							Page 63Installing DTB Type Multiline Monitors  •  •  •  Installation Manual
A6-506000-642-01
Wall Mounting Template
Use this template to mark the location of the screws on the wall. (Actual size.) 
						

							This page is intentionally blank.
Page 64Installing DTB Type Multiline Monitors  •  •  •  Installation Manual
A6-506000-642-01 
						

							Installation Manual  •  •  •  Installing DTU Type Multiline MonitorsPage 65
A6-506000-642-01
Xen AlphaRelease 1.0
SECTION 1
GENERAL
INFORMATION
The Xen Alpha system provides four different DTU-Type Multiline Terminals, and several
adapters that allow peripheral equipment to be attached to these Terminals. This chapter
describes each terminal and adapter, it also provides applicable installation instructions. 
SECTION 2
MULTILINE
TERMINALS
DTU-8-1A (WH) TEL
This digital non-display Multiline Terminal is equipped with eight programmable line keys
(each with a two-colour LED), a built-in speakerphone, headset jack, a large LED to indicate
incoming calls and messages, and compatibility with ADA-UA, APR-UA, CTA-UA, and HFU-
UA Units. 
Figure 4-1: DTU-8-1A (WH) TEL Multiline Terminal
DTU-8D-1A (WH) TEL
This digital Multiline Terminal has eight programmable line keys (each with the two-colour
LED), four softkeys, a built-in speakerphone, headset jack, a Large LED to indicate
incoming calls and messages, and compatibility with ADA-UA, APR-UA, CTA-UA, and HFU-
UA Units.
This terminal is also equipped with a 3-line, 24-character, adjustable Liquid Crystal
Display (LCD).
Figure 4-2: DTU-8D-1A (BK)/(WH) TEL Multiline Terminal
CHAPTER 
4Installing DTU-Type Multiline 
Te r m i n a l s 
						

							Page 66Installing DTU Type Multiline Monitors  •  •  •  Installation Manual
A6-506000-642-01
DTU-16D-1A (WH) TEL
This digital Multiline Terminal has 16 programmable line keys (each with a two-colour LED),
four softkeys, a built-in speakerphone, headset jack, a large LED to indicate incoming calls
and messages, and compatibility with ADA-UA, APR-UA, CTA-UA, and HFU-UA Units.
This terminal is also equipped with a 3-line, 24-character, adjustable Liquid Crystal
Display (LCD).
Figure 4-3: DTU-16D-1A (WH) TEL Multiline Terminal
DTU-32D-1A (WH) TEL
This digital Multiline Terminal has 16 programmable line keys (each with a two-colour LED),
16 one-touch keys, four softkeys, a built-in speakerphone, headset jack, a large LED to
indicate incoming calls and messages, and compatibility with ADA-UA, APR-UA, CTA-UA,
and HFU-UA Units.
This terminal is also equipped with a 3-line, 24-character, adjustable Liquid Crystal
Display (LCD).
System software can be changed so this Multiline Terminal can have 24 programmable line
keys and 8 one-touch keys.
Figure 4-4: DTU-32D-1A (WH) TEL Multiline Terminal 
						

							Installation Manual  •  •  •  Installing DTU Type Multiline MonitorsPage 67A6-506000-642-01
SECTION 3
CONNECTIN G A
M
ULTILINE
TERMINAL TO THE
SYSTEM
These instructions for connecting a Multiline Terminal to the system applies to all of the
DTU-type Multiline Terminals.
1. Plug the telephone cord into the modular jack on the bottom side of the Multiline Terminal. The handset is also attached to the bottom side of the Multiline Terminal.
Figure 4-5: Connecting a Multiline Terminal to the System
2. Lead the telephone and handset cords through the appropriate grooves.
Figure 4-6: Leading Line Cords on a Multiline Terminal 
						

							Page 68Installing DTU Type Multiline Monitors  •  •  •  Installation Manual
A6-506000-642-01
SECTION 4
ADJUSTING THE
LCDThe adjustable Liquid Crystal Display (LCD) comes equipped on the display DTU-type
Multiline Terminals. The LCD can be adjusted by pushing downward and upward as desired.
Figure 4-7: Adjusting the LCD
SECTION 5
INSTALLING LINE
CARDS &
P
LASTIC PANELS
Line Card and Plastic Panel Installation
Line Cards can be used to print the line key designations. These are then placed on the
Multiline Terminal providing a quick reference of key designations to the Multiline Terminal
users. The Line Cards can be changed as necessary. The Plastic Panel is placed on top of
the Line Card to hold it in place.
1. Place the Line Card over the keys on the Multiline Terminal.
2. Place the tabs on the bottom of the plastic panel into the grooves at the terminal
bottom, and press top right and left ends to secure plastic panel to the
Multiline Terminal. Refer Figure 4-8:: Installing Line Card and Plastic Panel on a
Multiline Terminal, Pg 68.
Figure 4-8: Installing Line Card and Plastic Panel on a Multiline Terminal