NEC Wt610e Projector User Manual

104
Menu
Selecting Menu Color [Menu Color Select]
You can choose a color for the menu.
Turning On / Off Source Display and Message [Display Select]
Source ................... This option turns on or off input name display such as Computer, DVI (DIGITAL/ANALOG), Video, and No
Input to be displayed in the top right corner of the screen.
Message ................ This option turns on and off messages. Even though selecting “Off”, the following message will appear.
* “The lamp has reached the end of its...

105
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The
preset choices are Manual, Auto 5 sec, Auto 15 sec, and Auto 45 sec. The Auto 45 sec is the factory preset.
NOTE:
•To display the last displayed menu again immediately after it is closed, press one of the MENU, the ENTER, the EXIT or the
SELECT 

 or .
•The [Test Pattern] and [Tilt Indicator] screens will be displayed independent of...

106
Setting a Password [Password (Menu)] / [Password (Logo)]
A password can be set for your projector to avoid operation by an unauthorized person.
When [Password (Menu)] is set, changing the menu from Basic to Advanced will display [Password (Menu)] input
screen.
When [Password (Logo)] is set, doing any one of the following two operations will display the Password input screen.
•Changing the background
•Changing the logo data in a PC card
Entry:
To assign your password:
NOTE: Up to 15 alphanumeric...

107
Security
The Security function enables you to protect your projector so that the projector will not project a signal unless you
enter a keyword. There is also an option to lock the projector by using a registered PC card* as a protect key. Once you
have registered your PC card as a protect key, you are required to insert the registered PC card into the PC card slot
of the projector each time you turn on the projector. You can enable the Security function by using a keyword only.
*The projector does...

108
The Security function takes effect.
To register a PC card as a protect key.
1. Insert a PC card into the PC card slot of the projector.
2. Use the SELECT 

 or  button to select Use Protect Key and press the ENTER button.
3. Use the SELECT 

 or  button to select Read and press the ENTER button.
Data of the PC card will be read into the projector.
4. Use the SELECT 

 or  button to select Register and press the ENTER button.
Downloaded data will be registered and be displayed in the list window....

109
To turn on the projector when Security is enabled (when using PC card as a protect key).
1. Insert your registered PC card into the PC card slot.
2. Press and hold the POWER button for a minimum of two seconds.
The projector will turn on and then recognize the PC card. Once the image has been projected, it will
stay on without the PC card.
•The security disable mode is maintained until the main power is turned off (by setting the main power switch
to O or unplugging the power cord). In the following...

110
Installation
Selecting Projector Orientation [Orientation]
This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.
Selecting Aspect Ratio and Position for Screen [Screen]
Screen Type ........... Select one of three options: 4:3 Screen or 16:9 Screen for the screen to be used. See also Aspect Ratio on
page 90.
Position ................. This feature allows you to adjust the...

111
[LAN Mode]
Setting LAN Mode
This feature allows you to set various setting items when the projector is used on your network.
CAUTION
•Consult with your network administrator about these settings.
•For wired LAN connection, use a commercially available wired LAN card and a LAN cable (Ethernet
cable). For more information on supported wired LAN cards for the NEC projectors, refer to the Service
Page for NEC Projectors (http://www.nec-pj.com).
•To use wired LAN, insert the wired LAN card into the PC...

112
To select a wireless LAN access point:
1. On the Profile tab, select Profiles and then select Profile 1 or Profile 2.
2. On the Profile tab, select Advanced” and press the ENTER button.
3. On the Advanced menu, select Network Type 
→ Site Survey and press the ENTER button.
4. Select Mode and then select Infrastructure.
See pages 113 and 114.
To receive error messages or information on the remaining lamp life via e-mail:
1. On the Mail tab, select Alert Mail and press the ENTER button. A check mark...

113
6. Using On-Screen Menu
Profile
Profiles (for PC Card):
To execute a wireless LAN easily using Image Express Utility 2.0, select “Easy Connection.
Up to two settings for the optional wireless LAN card can be stored in memory of the projector.
Select Profile 1 or Profile 2 and then do settings for DHCP and the other options.
After doing this, select “OK” and press the ENTER button. This will store your settings in memory.
DHCP:
Place a check mark to automatically assign an IP address to the projector...