NEC Vt595 Projector User Manual

23
3. Projecting an Image (Basic Operation)
 Adjusting the Picture Size and Position
F
O CUSM E
N USEL
E C T
L A M P
S T
A TU S
P O W ERO
N/
S TA N
D 
B Y S
O U
RC
E A
UTO  
A DJ.E N TE RE XI
TZ
O OM
FO C
USM EN USEL
E C T
L A M P
S TA T
U S
P O W ERO N
/S TA ND B Y S
O URC
E A
UTO  
A DJ.E N TE REXI
TZ
O OM
2
1PU SH
34
Adjustable Tilt Foot
Adjustable Tilt
Foot Button
Place your projector on a flat level surface and ensure that the project\
or is
square to the screen.
Lift the front edge of the...

24
3. Projecting an Image (Basic Operation)
MEN USELE CTLAMP
STATUS POWERO N/S
TA ND B
YSOU RCEA UTO  
A DJ.
EN
TEREXI
T
F O CUSZOOM
M EN USELECTLA M P
S TA TU S
P O W ERO N/ST AND B YSO
URC
EAUTO  A
DJ.
ENT ERE
XIT
F O C
US
Zoom
VT695/VT595/VT590/VT490/VT59
Use the ZOOM lever to adjust the image size on the screen.
VT49
Focus
Use the FOCUS ring to obtain the best focus.
VT695/VT595/VT590/VT490/VT59
F O CU SM EN US
ELE C T
L A M P
S TA TU S
P O W E
RO
N/S
TA N D B
Y S
O URCE A
UTO  A
DJ.E N TE RE
XITZ O...

25
 Correcting Keystone Distortion
Correcting Keystone Distortion
If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following
steps to correct keystone distortion
NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
NOTE: The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.
Adjusting with buttons on the cabinet
1. Press the SELECT 
 or  button with...

26
Adjusting with the Auto Keystone Function (VT695 and VT595 only)
The Auto Keystone correction feature will correct the vertical distortion of\
 a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
TIP: Even when the menu setting for [Auto Keystone] is turned on, [Keyst\
one] can be adjusted manually.
To turn on [Auto Keystone], proceed the following steps.
1. Press the MENU button
The menu will be displayed.
2. Press the SELECT  button to select...

27
3. Projecting an Image (Basic Operation)
 Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the AUTO ADJ. button to optimize an RGB image automatically.
This adjustment may be necessary when you connect your computer for the \
first time.
[Poor picture]
[Normal picture]
VOLUMEL-CLICK
MOUSER-CLICK
ASPECT HELP FREEZE
PICTURE
AUTO ADJ.S-VIDEO VIDEOCOMPUTER
LAMP MODE12
Increase volume
Decrease volumeVOLUMEL-CLICK
MOUSER-CLICK
ASPECT...

28
 Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
SELECT
MENU
ENTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCEENTEREXIT
MENU
UP
MAGNIFY PAGE OFF
POWER ON
PIC-MUTE
DOWN
1. First, press the POWER (ON/STAND BY) button on the projector cabinet or the POWER OFF button on
the remote control. The [Power Off / Are you sure?]message will appear.
2. Secondly, press the ENTER button or press the POWER (ON/STAND BY) or the POWER OFF buttonagain.
The power...

29
\b After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.4. Cover the lens with the lens cap.5. Put the projector and accessories in the supplied soft case. Place the projector in the soft case with the lens facing upward as show\
n below. This is to prevent the lens fromdamage.
3. Projecting an Image (Basic Operation)
NOTE: When placing the projector in the soft case, retract the tilt...

30
	 Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
NOTE:
Sound from the AUDIO OUT jack (Stereo mini) on the VT695/VT595 can be
turned off.

  Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume
motion.
 Enlarging a Picture
You can enlarge the picture up to four times.
NOTE: The maximum magnification may be less than four times depending on\
the signal....

31
 Changing Lamp Mode
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
To change to the [Eco] mode, do the following:
1. Press the LAMP MODE button on the remote control to display [Lamp Mode] \
screen.
2. Use the SELECT 

 or  button to select [Eco] mode.
3. Press the ENTER button.
To change from [Eco] to [Normal], Go back to Step 2 and select [Normal]. \
Repeat Step 3.
NOTE: • The Lamp Mode can be changed...

32
4. Convenient Features
5. Use the SELECT 
 or  button to select [On] and press the ENTER button.
The [Security Keyword] screen will be displayed.
6. Type in a combination of the four SELECT buttons  
 and press the ENTER button.
NOTE: A keyword must be 4 to 10  digits in length. Please make a note of\
 your keyword.
The [Confirm Keyword] screen will be displayed.
NOTE:Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code upon...