NEC Vt595 Projector User Manual

13
AUDIO OUT
AUDIO IN
MONITOR OUT (COMP 1)
COMPUTER 1 INCOMPUTER 2 (DVI-I) IN
AUDIO IN
S-VIDEOIN
VIDEO IN PC CTRL
L
R
COMPUTER 1 IN
AUDIO IN
PHONE
LCOMPUTER INMONITOR  OUT
AUDIO IN
S-VIDEO
IN
VIDEO IN PC CONTROLR
COMPUTER IN
2. Installation and Connections

 Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector an\
d notebook PC while the projector is in standby mode
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook...

14
2. Installation and Connections
When Viewing a DVI Digital Signal (VT695/VT595)
To project a DVI digital signal, be sure to connect the PC and the projec\
tor using a DVI cable (not supplied) before
turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the so\
urce menu
before turning on your PC.
Failure to do so may not activate the digital output of the graphics car\
d resulting in no picture being displayed. Should
this happen, restart your PC.
Do not...

15
Using Two Analog COMPUTER Inputs Simultaneously (VT695/VT595)
If you need to use two analog COMPUTER inputs simultaneously, connect a VGA signal cable as shown below.
AUDIO OUT
AUDIO IN
MONITOR OUT (COMP 1)
COMPUTER 1 INCOMPUTER 2 (DVI-I) IN
AUDIO IN
S-VIDEOIN
VIDEO IN PC CTRL
L
R
COMPUTER 1 INCOMPUTER 2 (DVI-I) IN
VGA signal cable
(supplied)
IBM PC or Compatibles (Notebook type) or Macintosh (Notebook type)
IBM PC or Compatibles (Desktoptype) or Macintosh (Desktop type)
VGA signal cable...

16
2. Installation and Connections
Connecting an External Monitor
You can connect a separate, external monitor to your projector to simulta\
neously view on a monitor the RGB analog
image youre projecting.
NOTE: • Daisy chain connection is not possible.
• The signal from the COMPUTER 2 IN connector cannot be output from the MO\
NITOR OUT connector on VT695 and VT595.
• When the DVI Digital signal is selected, no signals will be output from \
the MONITOR OUT connector on VT695 and VT595.
•The...

17
2. Installation and Connections
Connecting Your DVD Player with Component Output
A component signal will be automatically displayed. If not, from the men\
u, select [Setup]  → [Options]  → [Signal
Select]  → [Computer 1 ([Computer] on VT590/VT490/VT59/VT49)], and then place a \
check mark in the Component
radio button.
NOTE: Refer to your DVD players owners manual for more information abo\
ut your DVD players video output requirements.
AUDIO INLR
AUDIO OUT
LR
Component
YCbCr
AUDIO OUT
AUDIO IN...

18
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
NOTE: The AUDIO IN L/MONO and R jacks (RCA) are shared between the Vid\
eo and S-Video inputs.
NOTE: Refer to your VCR or laser disc player owners manual for more inf\
ormation about your equipments video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video so\
urce is played back in fast-forward or fast-rewind via
a scan converter.
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
AUDIO OUT
AUDIO...

19
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cable in the wall outlet.
CAUTION:
Do not try to touch the ventilation outlet on the left front (when seen\
 from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned\
 off.
CAUTION:
Do...

20
3. Projecting an Image (Basic Operation)
FOCUS
MENUS
ELE C
T
L A M
P
S TA TU
S
P O W ERO N/S TA ND B Y S
O URCE A
UTO  A DJ.E
N TE RE XI
T
STATUSLAMP POWER
SELECT
MENU
E
N TEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCE
MENU UP
MAGNIFY PAGE OFF
POWER ON
PIC-MUTEDOWN
POWERPOWER POWER
STATUS
LAMP STATUSLAMP
STATUSLAMP
Standby Blinking Power On
Steady orange light Blinking  green lightSteady green
light
(→  page  55)
This section describes how to turn on the projector and to project a pic\
ture...

21
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 8 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT 
 or  button to select one of the 8
languages from the menu.
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu op-
eration.
If you want, you can...

22
3. Projecting an Image (Basic Operation)
SELECT
MENU
ENTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCE
VOLUME L-CLICK
MOUSER-CLICK
AUTO ADJ.
ASPECT HELP
FREEZE
PICTURE
S-VIDEO VIDEOCOMPUTER
2LAMP MODE1
SELECT
MENU
E
NTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCE
  Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or video source equipment connected to the projector.
Selecting from Source List
Press and quickly release the SOURCE button on the...