NEC Television X462HB User Manual

							
English-19
English
OSD (On-Screen-Display) Controls
Press UP or DOWN
button to select
sub-menu.Press SET. Press UP or DOWN,
PLUS or MINUS to select
the function or setting to
be adjusted. Press MENU or EXIT.
Remote Control
Press UP or DOWN
button to select. Press INPUT button
to decide.Press UP or DOWN, PLUS
or MINUS button to select. Press EXIT
Control Panel
OSD screen
PICTURE MODE
Goto Adjustment
S elect Return Close
70
50
50
50
50
50
THANK YOU FOR SAVING
                         THE ENVIRONMENT.
CARBON FOOTPRINT            86.0 %
Input source
Main Menu Icons Main Menu Item
Sub Menu
Key Guide Adjustment Settings
NOTE:
Some functions may not be available depending on the model or optional e\
quipment. 
						

							
English-20
SettingDefault
BRIGHTNESS Adjusts the overall image and background brightness. Press + or - to adj\
ust. 70Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot be changed.
CONTRAST Adjusts the image brightness in relationship to the background. Press + \
or - to adjust. 50Note: When sRGB is selected in picture mode, this function cannot be cha\
nged.
SHARPNESS Adjusts the crispness of the image. Press + or - to adjust. 50*2
BLACK LEVEL Adjusts the image brightness in relationship to the background. Press + \
or - to adjust. 50Note: When sRGB is selected in picture mode, this function cannot be cha\
nged.
TINT Adjusts  the tint of the screen. Press + or - to adjust. 50
Note: When sRGB is selected in picture mode, this function cannot be cha\
nged.
COLOR Adjusts the color depth of the screen. Press + or - to adjust. 50*
2
Note: When sRGB is selected in picture mode, this function cannot be cha\
nged.
COLOR TEMPERATURE Adjusts the color temperature of the entire screen. A low color temperature will make the screen 10000K reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further
adjustment, the individual R/G/B/ levels of the white point can be adjus\
ted. To adjust the
R/G/B levels, CUSTOM must be showing as the COLOR TEMP selection.
Note: When sRGB is selected in picture mode, predefined 6500k is set so \
it cannot be changed.
When PROGRAMMABLE is selected in GAMMA SELECTION, this function cannot b\
e changed.
COLOR CONTROL Adjusts the hue of the Red, Yellow, Green, Cyan, Blue, Magenta and Saturation. 0
Note: When sRGB is selected in picture mode, this function cannot be cha\
nged.
GAMMA SELECTION Select a display gamma for best picture quality. NATIVE*
2
Note: When sRGB is selected in picture mode, this function cannot be cha\
nged. (except sRGB
NATIVE Gamma correction is handled by the LCD panel.
2.2 Typical display gamma for use with a PC.
2.4 Good for video (TV, DVD, etc.)
S GAMMA Special gamma for certain types of movies. Raises the dark parts and low\
ers the light parts
of the image (S-Curve).
DICOM SIM. DICOM GSDF curve simulated for LCD type.
PROGRAMMABLE A programmable gamma curve can be loaded using NEC optional software.
MOVIE SETTINGS NOISE REDUCTION Adjusts the amount of noise reduction. Press + or - to adjust. 6*
2TV, VIDEO1, VIDEO2, S-VIDEO inputs only
FILM MODE Automatically senses the sources frame rate for optimal picture quality. AUTO*2HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only
ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast. OFFHDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only
PICTURE MODE Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1] or STANDARD[AMBIENT2]. See page 18.
PICTURE RESET Resets the following settings within the PICTURE menu back to factory se\
tting: - BRIGHTNESS, CONTRAST, SHARPNESS, BLACK LEVEL, TINT, COLOR, COLOR
TEMPERATURE, COLOR CONTROL , GAMMA SELECTION, MOVIE SETTINGS.
AUTO SETUP Automatically adjusts Screen Size, H position, V position, Clock, Clock \
Phase and White Level. -VGA, RGB/HV inputs only
AUTO ADJUST H Position, V Position and Clock Phase are adjusted automatically upon p\
ower on. OFFVGA, RGB/HV inputs only
H POSITION Controls the horizontal position of the image within the Display area of\
 the LCD. -All inputs except DVI, HDMI, DPORTPress + to move right. Press - to move left.
V POSITION Controls the vertical position of the image within the Display area of t\
he LCD. -
All inputs except DVI, HDMI, DPORTPress + to move up. Press - to move down.
CLOCK Press + to expand the width of the image on the right of the screen. -
VGA, RGB/HV inputs onlyPress - to narrow the width of the image on the left.
CLOCK PHASE Adjusts the visual “noise” on the image. -
VGA, RGB/HV, DVD/HD1, DVD/HD2, SCART inputs only
*: The product you purchased may not have this feature. *2: depends on signal input
  PICTURE
  ADJUST
setting) 
						

							
English-21
English
H RESOLUTION Adjusts the horizontal size of the image. -VGA, RGB/HV inputs only
V RESOLUTION Adjusts the vertical size of the image. -VGA, RGB/HV inputs only
INPUT RESOLUTION If there is a problem with signal detection, this function forces the mo\
nitor to display the AUTOVGA, RGB/HV inputs onlysignal at the desired resolution. After selection, execute “AUTO SETUP” if required.If no problem is detected, the only available option will be “AUTO”.
ZOOM MODE Select the aspect ratio of the screen image. -
All inputs except TV*
BASE ZOOM CUSTOM
16:9 For input sources that have a 16:9 aspect ratio.
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only
14:9 For input sources that have a 14:9 aspect ratio.HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only
DYNAMIC Expands 4:3 picture to fill the screen. Some of the image is lost due to\
 expansion.HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only
OFF Selecting “OFF” will display the image in a 1 by 1 pixel format. (\
If the input resolution isAll inputs, except TV*higher than a 1920 x 1080 resolution, the image will be scaled down to f\
it the screen.)
CUSTOM Displays an image as large as possible without changing the aspect ratio\
.
All inputs, except TV*
ZOOM** Maintains the aspect ratio while zooming. 1.00
H ZOOM** Amount of horizontal zoom. Can be adjusted for each BASE ZOOM setting. 1.00
V ZOOM** Amount of vertical zoom. Can be adjusted for each BASE ZOOM setting. 1.00
H POS** Horizontal position. Can be adjusted for each BASE ZOOM setting. 0%
V POS** Vertical position. Can be adjusted for each BASE ZOOM setting. 0%
ASPECT Selects picture aspect, [FULL], [NORMAL], [WIDE] and [ZOOM]. See page 17\
. FULL
ADJUST RESET Resets the following settings within the ADJUST menu back to factory setting: - AUTO ADJUST, H POSITION, V POSITION, CLOCK, CLOCK PHASE, H RESOLUTION,
V RESOLUTION, ZOOM MODE, ASPECT.
BALANCE Adjust the balance of L/R volume. CENTERPress + button to move the stereo sound image to right.
Press - button to move the stereo sound image to left.
TREBLE To accentuate or reduce the high frequency sound. 0 Press + button to increase TREBLE sound.
Press - button to decrease TREBLE sound.
BASS To accentuate or reduce the low frequency sound. 0 Press + button to increase BASS sound.
Press - button to decrease BASS sound.
PIP AUDIO Selects source of PIP audio. MAIN AUDIO
LINE OUT Selecting “VARIABLE” enables control of the line out level with the VOLUME button\
. FIXED
SURROUND Artificial surround sound. OFF
AUDIO INPUT Selects audio input source [IN1], [IN2], [IN3], [DPORT], [HDMI], [TV]*, [OPTION]*.Depend on signal input
AUDIO RESET Resets “AUDIO” options back to factory settings. -
OFF TIMER Sets the monitor to power off after a length of time. OFFA time between 1 to 24 hours is available.
SCHEDULE SETTINGS Creates a working schedule for the monitor to use. -
SCHEDULE LIST List of schedules. -
DATE & TIME Sets the date, time, and daylight saving region. Date & time must be set\
 in order for the
“SCHEDULE” function to operate. See page 27.
YEAR Configures the year for the real time clock. -
MONTH Configures the month for the real-time clock. -
DAY Configures the day for the real-time clock. -
*: The product you purchased may not have this feature. **: 16:9, 14:9, CUSTOM only
  AUDIO
  SCHEDULE 
						

							
English-22
TIME Configures the time for the real-time clock. -
DAYLIGHT SAVING Configures daylight savings on or off. OFF
SCHEDULE RESET Resets the following settings within the SCHEDULE menu back to factory s\
etting: -
OFF TIMER, SCHEDULE SETTINGS.
KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off. OFFWhen Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.
PIP MODE Picture-in-Picture OFF
OFF OFF
PIP PIP
POP POP
SIDE BY SIDE (ASPECT)SIDE BY SIDE ASPECT
SIDE BY SIDE (FULL) SIDE BY SIDE FULL
PIP SIZE Selects the size of the sub-picture used in Picture-in-Picture (PIP) m\
ode. LARGE
SMALL
MIDDLE
LARGE
PIP POSITION Determines where the PIP appears on the screen. X = 95, Y = 92
ASPECT Selects sub picture aspect, [FULL], [NORMAL], [WIDE] and [ZOOM]. See pag\
e 17. FULL
TEXT TICKEROFF
MODE Enables Text Ticker and allows you to set Horizontal or Vertical direction.
POSITION Selects the location of the Text Ticker on the screen.
SIZE Determines the size of the Text Ticker in relationship to the overall screen size.
BLEND Sets the transparency of the Text Ticker (0: transparent, 100: opaque).
DETECT Enables auto-detection of the Text Ticker.
FADE IN Enables fade-in of the text ticker.
SUB INPUT Selects sub picture input signal.Depends on signal input
PIP RESET Resets PIP options back to factory settings except ASPECT and SUB INPUT. -
LANGUAGE Select the language used by the OSD. ENGLISH
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SVENSKA
РУССКИЙ
OSD TURN OFF Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds. 30 Sec.
OSD POSITION Determines the location where the OSD appears on the screen.X = 128, Y = 225
UP
DOWN
LEFT
RIGHT
  PIP
  OSD
(Depends on
destination) 
						

							
English-23
English
INFORMATION OSD Selects whether the information OSD is displayed or not. The information OSD will be ON, 3 Sec.displayed when the input signal or source changes. The information OSD will also give a
warning when there is no-signal or the signal is out-of range.
An interval between 3 to 10 seconds for the Information OSD to appear is\
 available.
MONITOR INFORMA TIONMonitor Information. -
CARBON SAVINGS:  Display the estimated carbon saving information in kg. The carbon
footprint factor in the carbon saving calculation is based on the OECD (\
2008 Edition).
OSD TRANSPARENCY Set the transparency level of the OSD. TYPE2
OFF
TYPE1
TYPE2
OSD ROTATION Determines the OSD display direction between landscape and portrait. LANDSCAPE
LANDSCAPE Display the OSD with landscape mode.
PORTRAIT Display the OSD with portrait mode.
INPUT NAME You can create a name for the INPUT currently being used. -
Max: 8 characters, including Space, A-Z, 0-9, and some symbols.
CLOSED CAPTION Activates closed captioning. OFF
VIDEO1, VIDEO2, S-VIDEO inputs only
OSD RESET Resets the following settings within the OSD menu back to factory settin\
g: -
OSD TURN OFF, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY,
CLOSED CAPTION.
MONITOR ID Sets the monitor ID number from 1-100 and group ID from A-J. 1NOTE: Group ID is made of multiple selections.
IR CONTROL Selects the mode of the monitor for use with the infra-red remote contro\
l when using the NORMAL
RS-232C daisy chain.
NORMAL The monitor will be controlled normally using the remote controller.
PRIMARY Choose “PRIMARY” for the first monitor within an RS-232C daisy chain.
SECONDARY Choose “SECONDARY” for all subsequent monitors within an RS-232C daisy chain.
LOCK Prevents the monitor from being controlled by the wireless remote contro\
ller. To return to
normal operation, press the “DISPLAY” button on the remote controller for 5 seconds.
TILE MATRIX Allows one image to be expanded and displayed over multiple screens (up\
 to 100) through a distribution amplifier.
NOTE: Low resolution is not suitable for tiling to a large number of mon\
itors. You can operate
without a distribution amplifier at a lower number of screens.
H MONITORS Number of monitors arranged horizontally. 1
V MONITORS Number of monitors arranged vertically. 1
POSITION Select which section of the tiled image to be displayed on the monitor. 1
TILE COMP Turns the TILE COMP feature on. NO
ENABLE Enables Tile Matrix. NO
POWER ON DELAY Adjusts the delay time between being in “standby” mode and enterin\
g “power on” mode. 0 Sec.
“POWER ON DELAY” can be set between 0 and 50 seconds.
POWER INDICATOR Turns ON or OFF the LED located at the front of the monitor. ON
If “OFF” is selected, LED will not light when the LCD monitor is i\
n active mode.
EXTERNAL CONTROL
CONTROL Selects the control interface, RS-232C or LAN. RS-232C
LAN RESET Resets the LAN settings. -
ID=ALL REPLY When controlling the monitor externally, select if the communication command, which specifies ON destination equipment ID (ALL or GROUP ID), is replying or not. Use this function as necessary,
if you connect the multiple monitors that are daisy-chained from secondl\
y monitor by RS-232C.
MAC ADDRESS Displays the MAC ADDRESS. -
  MULTI DISPLAY 
						

							
English-24
LAN SETTING When you use this function, EXTERNAL CONTROL should be “LAN”.NOTE: When changing the LAN SETTING, you need to wait several seconds un\
til the LAN
SETTING is applied.
DHCP Enabling this option automatically assigns an IP address to the monitor from your DHCP server. DISABLE Disabling this option allows you to register the IP address or subnet ma\
sk number obtained
from your network administrator.
NOTE: Consult your network administrator for the IP address when “ENA\
BLE” is selected for [DHCP].
IP ADDRESSSet your IP address of the network connected to the monitor when “DIS\
ABLE” is selected for [DHCP].192.168.0.10
SUBNET MASK Set your subnet mask number of the network  connected to the monitor when “DISABLE” is 255.255.255.0
selected for [DHCP].
DEFAULT GATEWAY Set your default gateway of the  network connected to the monitor when “DISABLE” is selected 192.168.0.1
for [DHCP].
DNS PRIMARY Set your primary DNS settings of the network connected to the monitor. 0.0.0.0
DNS SECONDARY Set your secondary DNS settings of the network connected to the monitor. 0.0.0.0
SETTING COPY In a daisy chain scenario, select the OSD menu categories that you want \
to copy over to the NO other monitor. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”.
This function resets to default when power is off. This function has a limit depending on the
cable you use.
COPY START Select “YES” and press the SET button to start copying.
ALL INPUT All input terminals settings are copied when you select this item. Defau\
lt is off.
MULTI DISPLAY RESET Resets “MULTI DISPLAY” options back to factory settings. -
POWER SAVE Sets how long the monitor waits to go into power save mode after the sig\
nal is lost. ONAll inputs except for TV*Note: When connecting DVI, the video card might not stop sending the dig\
ital data even though
the image might have disappeared. If this occurs the monitor will not sw\
itch into power
management mode (standby mode).
STANDBY MODE Lowers power consumption. ECO
Note: When in ECO STANDBY mode, DDC/CI does not function. STANDBY
HEAT STATUS Displays status of the FAN, BRIGHTNESS and TEMPERATURE. -
FAN CONTROL Cooling fans are running always for X462HB. -
SCREEN SAVER Use the SCREEN SAVER function to reduce the risk of Image Persistence.
GAMMA The display gamma is changed and fixed when “ON” is selected. OFF
BRIGHTNESS The brightness is decreased when “ON” is selected. OFF
NOTE: Do not select this function when picture model is AMBIENT1 or AMBIENT2.
MOTION The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) OFF at user determined intervals. You can set interval time and zooming ratio.
This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.
SIDE BORDER COLOR Adjusts the color of the side borders when a 4:3 image is displayed. 15 Press + button, the bar will become lighter.
Press - button, the bar will become darker.
AUTO BRIGHTNESS Adjusts the brightness level according to the input signal. OFF
DPORT, DVI, VGA, RGB/HV inputs onlyNOTE: Do not select this function when picture model is AMBIENT1 or AMBIENT2.
CHANGE SECURITY Allows the security password to be changed. -
PASSWORD The factory preset password is 0000.
SECURITY LOCK Locks the security password. OFF
DDC/CI ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor. ENABLE
DISPLAY PROTECTIONResets the following settings within the DISPLAY PROTECTION menu back to factory setting: -
RESET POWER SAVE, STANDBY MODE, SCREEN SAVER, SIDE BORDER COLOR,
AUTO BRIGHTNESS, DDC/CI.
  DISPLAY PROTECTION
*: The product you purchased may not have this feature. 
						

							
English-25
English
INPUT DETECT Selects the method of input detection the monitor uses when more than tw\
o input devicesFIRST DETECTAll inputs except for TV*are connected.
NONE The Monitor will not search the other video input ports.
FIRST DETECT When the current video input signal is not present, then the monitor sea\
rches for a video signalfrom the other video input port. If the video signal is present in the o\
ther port, then the monitor
switches the video source input port to the new found video source autom\
atically.
The monitor will not look for other video signals while the current vide\
o source is present.
LAST DETECT When the monitor is displaying a signal from the current source and a ne\
w secondary source is supplied to the monitor, the monitor will automatically switch to the new video source.
When current video input signal is not present, the monitor searches for\
 a video signal from
the other video input port. If the video signal is present in the other \
port, then the monitor
switches the video source input port to the new found video source autom\
atically.
VIDEO DETECT DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2 or S-VIDEO inputs will have priority over DVI, VGA, RGB/HV. When DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2 or S-VIDEO
input signal is present the monitor will change and keep to the DVD/HD1,\
 DVD/HD2, SCART,
VIDEO1, VIDEO2 or S-VIDEO input.
CUSTOM DETECT Set the priority of input signals.
When CUSTOM DETECT is selected, monitor searches listed inputs only.
INPUT CHANGE Sets input change speed. NORMAL
NOTE: When “QUICK” is selected, picture may be distorted when sign\
al input is changed.
This function should be chosen after all adjustment options have been ma\
de for the input.
LONG CABLE COMP Manually compensates for image degradation caused from using a long cabl\
e.
EQUALIZE OFF
VGA, RGB/HV inputs only
POLE Adjusts frequency.0
PEAK Adjusts equalizing value.0
GAIN Adjusts gain value.0
OFFSET Adjusts slice level of synchronized signal. 0
SYNC TERMINATE Selects the terminate resistance for matching the cable impedance. HIGH
RGB/HV inputs only
TERMINAL SETTING DVI MODE Selects the kind of DVI-D equipment which is connected to the DVI input.\
 Select “DVI-PC” DVI-PC when PC or other computer equipment is connected. Select “DVI-HD” \
when DVD player,
which has DVI-D output, is connected.
BNC MODE Selects the kind of equipment which is connected to the BNC input. RGB RGB: Analog  input
COMPONENT: Component
VIDEO:
SCART MODE Input mode for devices using SCART connectors. OFF
HDMI SIGNAL RAW: Disable the expanded feature. EXPAND
EXPAND: Expand image contrast and increase detail in the dark and bright ar\
eas.
SCAN CONVERSION Selects the IP (Interlace to Progressive) conversion function.
PROGRESSIVE
All inputs except VGA, RGB/HVNote: For DVI input “DVI-HD” needs to be enabled in the DVI mode m\
enu.
PROGRESSIVE Converts interlaced signals to progressive. This is the default setting.
INTERLACE Disables IP conversion. This setting is best suited for motion pictures, but increases the risk
of image retention.
*: The product you purchased may not have this feature.
  ADVANCED OPTION 
						

							
English-26
COLOR SYSTEM The selected Color System depends on the video format of the input signa\
l. AUTOVIDEO1, VIDEO2, S-VIDEO inputs only
AUTO Automatically chooses Color System setting based on input signal.
NTSC
PA L
SECAM
4.43 NTSC
PAL-60
SCAN MODE Some video formats may require different scanning modes  in order to best display the image.OVER SCAN
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only
OVER SCAN Image size is larger than what can be displayed. The image edge will appear cropped.Approximately 95% of the image will be shown on the screen.
UNDER SCAN Image size stays within the display area. The whole image is displayed on the screen.
120 Hz (Not available)-
EDGE COMP (Not available)-
ADVANCED OPTION Resets the following settings within the ADVANCED OPTION menu back to factory setting: -
RESET INPUT DETECT, INPUT CHANGE, LONG CABLE COMP, TERMINAL SETTING, SCAN
CONVERSION, COLOR SYSTEM, SCAN MODE.
FACTORY RESET Resets OSD options back to factory settings EXCEPT FOR: DATE & TIME, LANGUAGE, - OSD ROTATION, INPUT NAME, CHANGE SECURITY PASSWORD, SECURITY LOCK and
SECURITY PASSWORD.
*: The product you purchased may not have this feature. 
						

							
English-27
English
NOTE 1: CREATING A SCHEDULE
The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be
programmed.
To program the schedule:
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and do\
wn buttons. Press the SET or the + button to enter th e
Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule c an now
be programmed.
2. Use the down button to highlight the hours setting in the ON time slot. \
Use the + and - buttons to set the hour. Use the up a nd down
buttons to highlight the minutes setting. Use the + and - buttons to set\
 the minutes. Set the OFF time in the same manner.
3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and dow\
n arrows  to
highlight PIC. MODE. Use the + and - buttons to choose the picture mode.\
4. Use the down button to select a day on which the schedule will be enable\
d. Push the set button to enable. If the schedule is to be ran every day, choose EVERY DAY and
press the SET button. The circle next to EVERY DAY will turn yellow. If a weekly
schedule is desired, choose the days of the week using the up and down b\
uttons and
pressing SET to select. Then highlight the EVERY WEEK option and press SET.
5. After a schedule is programmed the remaining schedules can then be set. \
Press MENU to leave the OSD or press EXIT to go back to the previous menu.
Note:  If schedules are overlapping then the schedule with the highest number w\
ill have
priority over the schedule with the lowest number. For example schedule #7 will have
priority over schedule #1.
If selected input or picture mode is not available now, disable input or picture mode
is shown in red.
NOTE 2:  IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image \
Persistence occurs when a
residual or “ghost” image of a previous image remains visible on t\
he screen. Unlike CRT monitors, LCD monitors’ image persisten ce is not
permanent, but constant images being displayed for a long period of time\
 should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For examp\
le, if an image  was on the
monitor for one hour and a residual image remains, the monitor should be\
 turned off for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen\
saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce t\
he risk of Image persistence.
For long life use as Public Display
Image Sticking of LCD Panel
When an LCD panel is operated continuously for long hours, a trace of el\
ectric charge remains near the electrode inside LCD, an d residual
or “ghost” image of previous image may be observed. (Image Persis\
tence)
Image Persistence is not permanent, but when fixed image is displayed fo\
r long period, ionic impurities inside LCD are accumula ted along
the displayed image, and may be permanent. (Image Sticking)
Recommendations
To prevent Image Sticking, and for longer life usage of LCD, the followin\
g are recommended.
1. Fixed image should not be displayed for long period. Change fixed images\
 after short intervals.
2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule\
 Functions.
3. Lower environmental temperatures prolong the lifespan of the monitor. When Protective surface (glass, acrylic) is installed over the LCD sur\
face, the LCD surface is located in an enclosed space, th e monitor
are stacked, utilize the temperature sensors inside monitor.
To reduce the environmental temperature, use the Cooling Fan, Screen Save\
r and Low Brightness.
4. Please use “Screen Saver Mode” of monitor.
SCHEDULE:
ON: – – : – –
OFF: – – : – – – – – –
INPUT:
PIC. MODE: – – – –
DVI
(THU) JUN.18.2009 15:38 
SETTINGS:OFF TIMER
SCHEDULE SETTINGS
SCHEDULE LIST
DATE & TIME
SCHEDULE RESET  RESET

MON TUE WED THUSATSUNFRI
1234567
ChooseMark Return Close
EVERY DAYEVERY WEEK 
						

							
English-28
REMOTE CONTROL ID FUNCTION
REMOTE CONTROL ID
The remote control can be used to control up to 100 individual MultiSync\
 monitors using
what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode
works in conjunction with the Monitor ID, allowing control of up to 100 \
individual
MultiSync monitors. For example: if there are many monitors being used i\
n the same
area, a remote control in normal mode would send signals to every monito\
r at the same
time (see Figure 1). Using the remote in REMOTE CONTROL ID mode will o\
nly operate
one specific monitor within the group (see Figure 2).
TO SET REMOTE CONTROL ID
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD
to input the Monitor ID (1-100) of the display to be controlled via re\
mote. The remote can
then be used to operate the monitor having that specific Monitor ID numb\
er.When 0 is selected or when the remote control is in normal mode, all mon\
itors will be
operated.
TO SET/RESET REMOTE CONTROL MODE
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for
2 seconds. Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold
down for 2 seconds.
In order for this feature to work properly, the display must be assigned a Monitor ID
number. The Monitor ID number can be assigned under the MULTI DISPLAY menu in the
OSD (See page 23).
Point the remote control towards the remote sensor of the desired monito\
r and press the
REMOTE ID SET button. The MONITOR ID number is shown on the display when your remote control is in ID m\
ode.
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.
1. Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100. This MONITOR ID number allows the remote control to operate this specific monitor \
without affecting other monitors.
2. On the remote control, press and hold down the REMOTE ID SET button w\
hile using the keypad to input the REMOTE CONTROL ID number (1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to
simultaneously control all displays in range.
3. Point the remote control towards the remote sensor of the desired mon\
itor and press the REMOTE ID SET button. The MONITOR ID number is shown in red on the display.
If the REMOTE CONTROLID is “0”, then all displays in range will sh\
ow their respective MONITOR ID number in red.
If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.
This LCD monitor can be controlled via personal computer or wireless rem\
ote control using an RS-232C connection.
MONITOR ID and IR CONTROL
Using one PC or one infrared wireless controller, up to 100 individual LCD monitors can be controlled through a daisy ch\
ain via  RS-232C
connection.
1. Connect PC and LCD monitors. Connect a PC’s RS-232C control output to the LCD monitor RS-232C input. You can then connect the RS-232C output from the LCD
monitor to another LCD monitor RS-232C input. Up to 100 monitors can be \
connected using RS-232C.
2. Set Monitor ID and IR Control mode. For proper operation, the Monitor ID should be set in the OSD menu of ea\
ch monitor that is in the chain. The Monitor ID can be  set under
the “MULTI DISPLAY” menu in the OSD. The Monitor ID number can be set within a range from 1 to 100. No two mo\
nitors should shar e
the same Monitor ID number. It is recommended to number each monitor in a daisy chain sequentially\
 from 1. The first monitor in  the daisy
chain is designated as the primary monitor. Subsequent monitors with the chain are secondary monitors.
In the “ADVANCED OPTION” menu on the first monitor in the RS-232C daisy chain se\
t the “IR CONTROL” to “PRIMARY”.
Set the “IR CONTROL” to “SECONDARY” on all other monitors.
Remote Control Function
Monitor ID:1 Monitor ID:2 Monitor ID:3
Monitor ID:1 Monitor ID:2 Monitor ID:3
Remote does not work Remote does
not work Remote works
Remote works Remote works Remote works
Figure 1
Remote in
Normal mode or
the REMOTE ID is set to 0
Figure 2
Remote set up to use REMOTE ID:3