NEC Television X462HB User Manual

User’s Manual
MultiSync X462HB 

Index
Declaration of conformity ........................................................................\
..................................................... English-1
Important Information ........................................................................\
.................................. ......................... English-2
WARNING, CAUTION ........................................................................\
....................................... ......... English-2
Declaration...

English-1
EnglishFor USA
FCC Information
1. Use the attached specified cables with the MultiSync X462HB (X462HB) c\
olor display so as not to interfere with radio andtelevision reception.
(1) Please use the supplied power cord or equivalent to ensure FCC complianc\
e.
(2) Please use a good quality shielded video signal cable.
Use of other cables and adapters may cause interference with radio and t\
elevision reception.
2. This equipment has been tested and found to comply with the limits for a\
 class A...

English-2
Important Information
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROMWALL SOCKET. TO FULLY DISENGAGE...

English-3
EnglishFOR OPTIMUM PERFORMANCE, PLEASE NOTE THEFOLLOWING WHEN SETTING UP AND USING THE MULTI-FUNCTION MONITOR:
• DO NOT OPEN THE MONITOR . There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other risks.
Refer all servicing to qualified service personnel.
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage...

English-4
Contents
Power Cord*1
Setup ManualClamp x 3
Your new MultiSync monitor box* should contain the following:
• LCD monitor
• Power cord*
1
• Video Signal Cable
• Wireless Remote Control and AA Batteries
• Setup Manual
• Cable cover
• Clamp x 3
• Screw (M4 x 10) x 9
• CD-ROM
• Thumbscrew for optional stand x 2*
2
CD-ROMScrew (M4 x 10) x 9
* Remember to save your original box and packing material to transport or \
ship the monitor.
*
1Type and number of power cords included will depend on the where...

English-5
EnglishThis device cannot be used or installed without the TabletopStand or other mounting accessory for support. For properinstallation it is strongly recommended to use a trained,NEC authorized service person. Failure to follow NECstandard mounting procedures could result in damage to theequipment or injury to the user or installer. Product warrantydoes not cover damage caused by improper installation.Failure to follow these recommendations could result invoiding the warranty.
Mounting
DO...

English-6
Attaching Mounting Accessories
The display is designed for use with the VESA mounting
system.
1. Attach Mounting Accessories
Be careful to avoid tipping monitor when attaching
accessories.
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the screen face,
place the protective sheet on the table underneath the LCD.
The protective sheet was wrapped around the LCD in the
original packaging. Make sure there is nothing on the table
that can damage...

English-7
English
 EXIT button
Activates the OSD menu when the OSD menu is turned-off.
Acts as EXIT button within the OSD to move to previous
menu.
  Remote control sensor and Power Indicator
Receives the signal from the remote control (when using the
wireless remote control). See also page 11.
Glows green when the LCD monitor is in active mode*.
Glows red when the LCD is in POWER OFF (ECO standby)
mode. Glows amber when the LCD is in POWER OFF
(standby) mode. Blinks amber when the monitor is in Power...

English-8
Terminal Panel
Out
In
RGBHVRGB/HVRGBHVDVD/HD2 Pr Y Pb
VIDEO2VIDEO
 VIDEO IN connector (BNC and RCA)
To input a composite video signal. BNC and RCA connectors
are not available at the same time (Use only one input).
  VIDEO OUT connector (BNC)
To output the composite video signal from the VIDEO IN
connector.
  DVD/HD connector (RCA)
Connecting equipment such as a DVD player, HDTV device,
or Set-Top-Box.
 S-VIDEO IN connector (Mini DIN 4 pin)
To input the S-video (Y/C separate signal).
 AUDIO IN...