NEC Roamer An Open Application Interface Installation Guide

NDA-30016    Revision 3.0Page 5
Roamer Installation Guide Application Configuration
Chapter 2 Application Configuration
Roamer is configured into the APM system using the Add function of the 
Application Configuration option on the APM System Administration menu:
1. Enter the APM option from the APM Platform Management Menu.
2. Enter the System Administrator password at the APM password screen.
3. Enter the Application Configuration option from the System Administration 
menu.
This section contains the...

Page 6NDA-30016   Revision 3.0
Application Configuration Roamer Installation Guide
Step 2: Primary Configuration Parameters
On the APM Configuration Entry screen, make the entries shown below to the 
parameters indicated.
Note:
Entries for parameters that are marked with an asterisk (*) should be made ex-
actly as they are shown. All other entries in this guide serve only as examples.
Parameter Entry Description
Application Name Roamer The name to be displayed in the 
APM menus. This name is 
displayed...

NDA-30016   Revision 3.0Page 7
Roamer Installation Guide Application Configuration
Step 3: OAI Facilities
According to instructions in the APM Operations Manual, designate the following 
NEAX2400 facilities for Roamer using the Facilities command on the 
Configuration Entry screen:
FLF Free Location MRFR Mode Release (R)
MRFI Mode Release (I) MSF OAI Mode Set
NTF Number Transfer TCFD Terminal Control (D)
TCFI Terminal Control (I)
Note:The same MSF identification number (i.e., from 128 to 192) that is...

Page 8NDA-30016   Revision 3.0
Application Configuration Roamer Installation Guide
Step 4: Secondary OAI Configuration Parameters
Using the OAI-Conf command on the APM Configuration Entry screen, make the 
entry shown for each of the following parameters required by Roamer. Use the 
instructions provided for this option in the APM Operations Manual:
Parameter Entry Description
Database Name #1* /oai/db/cur/
roamerdbThe path name of the database 
containing user information. The 
database filename...

NDA-30016   Revision 3.0Page 9
Roamer Installation Guide Application Configuration
Step 5: User-Defined Parameters
Make the following additional parameter entries through the UserDefined 
command on the APM Configuration Entry screen:
Parameter Entry Description
User Defined #1 3 The number of the Roamer Dterm 
function key LED. This number 
must correspond to the function 
key assigned to Roamer at the 
NEAX MAT. For more 
information, see Chapter 4, “MAT 
Assignments” on page 15.
User Defined #2 0 The...

Page 10NDA-30016   Revision 3.0
Application Configuration Roamer Installation Guide
This completes the configuration of Roamer in the APM. Now go to Chapter 3, 
“Database Requirements” on page 11 to create its database support. User Defined #7 0 The number of 30-minute 
intervals that the backup file will 
remain valid after a power failure. 
The largest allowable value is 48 
(24 hours). A longer delay must 
be indicated with the value 0 
(always valid).
User Defined #8* /oai/app/data/
roamerbuThe name...

NDA-30016    Revision 3.0Page 11
Roamer Installation Guide Database Requirements
Chapter 3 Database Requirements
Roamer uses the following two databases, only the first of which is created through 
the APM:
The Roamer Database 
This database contains default assignment information. Each user ID is 
associated to telephone numbers and privileges, a tenant, and a reset option. 
This database is created through the APM and is configured as /oai/db/cur/
ro am erd b.
The Backup Database 
This database...

Page 12NDA-30016   Revision 3.0
Database Requirements Roamer Installation Guide
Instructions
The information required in all four steps is provided in table below. Using this 
information with the procedural instructions provided in the APM Operations 
Manual, enter the Database Administration option on the APM System 
Administration Menu, and build the Roamer database. Any messages displayed 
during these steps are discussed in the Process and Error Messages chapter of the 
APM Operations Manual.
The...

NDA-30016   Revision 3.0Page 13
Roamer Installation Guide Database Requirements
Field DefinitionsUser ID A unique 10-digit number that describes each user 
(e.g. social security number). The database is sorted by 
this field.
User Name The 16-character user name that is displayed on the 
D
term.
Logical Number The station number associated with the user name 
under Roamer control.
Exempt from Reset? Whether or not (Yes or No) this user is to be reset to a 
home phone when all system phones are reset....

Database Requirements Roamer Installation Guide
Page 14NDA-30016   Revision 3.0
This Page Left Blank.