NEC PX 60XM5 User Manual

En-10
AAC IN
Connect the included power cord here.
BEXT SPEAKER L and R
Connect speakers (optional) here. Maintain the correct
polarity. Connect the 
 (positive) speaker wire to the
 EXT SPEAKER terminal and the  (negative)
speaker wire to the 
 EXT SPEAKER terminal on
both LEFT and RIGHT channels.
Please refer to your speaker’s owner’s manual.
CVIDEO1, 2, 3 (BNC, RCA, S-Video)
Connect VCR’s, DVD’s or Video Cameras, etc. here.
VIDEO1 can be used for Input or Output.
DAUDIO1, AUDIO2, AUDIO3
These are...

En-11
VIDEO(IN/OUT)
(IN/OUT)AUDIO 1DVD1 / HD1R
1
3 2
(MONO)LY Cb / Pb Cr / Pr
RGB2 / DVD2 / HD2RGB 1VD HD
DV I  (
Digital  RGB)R
LAUDIO 2
(MONO)
R
LAUDIO 3
(MONO)
R/Cr/Pr G /Y B/Cb/PbRGB 3
IN OUT
REMOTEEXTERNAL CONTROL
VIDEO(IN/OUT)AUDIO 1DVD1 / HD1Y L/R L/RCb / Pb Cr / PrRGB2 / DVD2 / HD2RGB 1VD L/R HD
DV I   AUDIO 2AUDIO 3R/Cr/Pr G /Y B/ Cb /PbRGB 3EXTERNAL CONTROLIN OUTREMOTE
BAL
D
CE F G H IJK
AAC IN
Connect the included power cord here.
BEXT SPEAKER L and R
Connect speakers (optional) here. Maintain...

En-12
q POWER ON/STANDBY
Switches the power on/standby.
(This does not operate when the POWER/STANDBY
indicator of the plasma is off.)
w RGB/PC
Press this button to select RGB/PC as the source.
RGB/PC can also be selected using the INPUT
SELECT button on the monitor.
eDVD / HD
Press this button to select DVD/HD as the source.
DVD/HD can also be selected using the INPUT
SELECT button on the monitor.
rVIDEO
Press this button to select VIDEO as the source.
VIDEO can also be selected using the INPUT SELECT...

En-13
Basic Operations
POWER
To turn the unit ON and OFF:
1. Plug the power cord into an active AC power outlet.
2. Press the Power button (on the unit).
The monitor’s POWER/STANDBY indicator turns red
and the standby mode is set.
3. Press the POWER ON button (on the remote control) to
turn on the unit.
The monitor’s POWER/STANDBY indicator will light
up (green) when the unit is on.
4.
Press the POWER STANDBY button (on the remote control)
or the Power button (on the unit) to turn off the unit.
The...

En-14
WIDE Operations
Wide Screen Operation (manual)
With this function, you can select one of seven screen sizes.
When viewing videos or digital video discs
1. Press the WIDE button on the remote control.
2.Within 3 seconds ...
Press the WIDE button again.
The screen size switches as follows:
→ NORMAL → FULL → STADIUM → ZOOM → 2.35:1 → 14:9 → UNDERSCAN
When a 720P or 1080I signal is input:
FULL ↔  2.35:1
When displaying enhanced split screen:
NORMAL ↔  FULL
NORMAL size screen (4:3)
The normal size...

En-15
FULL size screen
The image is expanded in the horizontal and vertical
direction.
ZOOM size screen
When wide signals are input.
TRUE
The image is true resolution.
FULL
Information
 Supported resolution
See page En-41 for details on the display output of the
various VESA signal standards supported by the
monitor.
 “PICTURE SIZE” setting
When the setting of “PICTURE SIZE” is OFF, the size
of RGB-input pictures will be TRUE in place of
NORMAL.
When 852 (848) dot  480 line wide VGA*
signals with a...

En-16
Showing a couple of pictures on the
screen at the same time
* There may be some RGB-input  signals that may not be
displayed as not all signals are supported.
1. Press the button to select a screen mode from among single
mode, side-by-side, and picture-in-picture.
Note:
Picture A and B on the above screen are not always of the
same height.
Information
Split screen operations may not function depending on
the combination of input signals. In the table below,
“” means Yes, “” means No.
Split...

En-17
Operations in the Picture-in-picture mode
To move the position of the sub screen, press the cursor 
or  button.
To change the size of the sub screen, press the 
 button.
VIDEO1RGB1
AB
VIDEO1RGB1
AB
VIDEO1RGB1
AB
VIDEO1RGB1
AB
 button
 button
 button
 button
To make the desired picture active, press the SELECT/
FREEZE button.
Selecting the input signals to be displayed
1. Press the SELECT/FREEZE button to make the desired
picture active.
2. Press the RGB/PC, VIDEO, or DVD/HD button.
Each...

En-18
Menu Operations
The OSM window is displayed with respect to the
screen as shown on the diagram.
* Depending on the screen’s mode, the OSM may be
displayed differently.
In the explanation, the OSM section is shown close up.
SEL.
MAIN MENU 1 / 2
PICTURE
AUDIO
IMAGE ADJUST
OPTION 1
ADVANCED OSM
      NEXT PAGE:   OFF
EXIT
MENU/ENTEROKEXIT
The following describes how to use the menus and the
selected items.
1. Press the MENU/ENTER button on the remote control to
display the MAIN MENU.
SEL.
MAIN MENU 1...

En-19
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE
PICTURE CONTRAST←→  0←52→72 YES YES En-21
BRIGHTNESS←→  0←32→64 YES YES En-21
SHARPNESS←→  0←16→32 YES YES En-21
COLOR←→  0←32→64 YES YES En-21
TINT R←→G     0←32→64 YES YES En-21
PICTURE MODE BRIGHT/NORMAL/THEAT.1/THEAT.2/DEFAULT YES YES En-21
NR OFF/NR-1/NR-2/NR-3 YES YES En-21
COLOR TEMP. LOW/MID LOW/MID/HIGH YES YES En-21
WHITE BALANCE GAIN RED←→  0←40→70 YES NO En-22
GAIN GREEN←→  0←40→70 YES NO...