NEC Px 50xr6 Operation Manual

							En-9
R 1
2
(MONO)LY Cb/Pb Cr/Pr
R
LY Cb/Pb Cr/Pr
(MONO)
R
L
(MONO)
IN
OUTHDMIHDMIVIDEO AUDIO1DVD/HD1DVD/HD2DVD/HD3DVD/HD4PC/RGB AUDIO2AUDIO 3REMOTEEXTERNAL CONTROL
VIDEO AUDIO1DVD/HD1DVD/HD2DVD/HD3DVD/HD4PC/RGB AUDIO2AUDIO 3REMOTEEXTERNAL CONTROLCb / Pb Cr/ Pr L/R Y Cb/Pb Cr/Pr L/R Y
L/RIN OUT
D
CE F G H IJKBAL
Rear View/ Terminal Board
60XR5
HDMI, the HDMI logo and High-Definition Multimedia Interface are 
trademarks or registered trademarks of HDMI Licensing LLC.
AAC IN
Connect the included power cord here.
BEXT SPEAKER L and R
Connect speakers (optional) here. Maintain the correct
polarity. Connect the 
 (positive) speaker wire to the
 EXT SPEAKER terminal and the  (negative)
speaker wire to the 
 EXT SPEAKER terminal on
both LEFT and RIGHT channels.
Please refer to your speaker’s owner’s manual.
CVIDEO1, 2 (RCA, S-Video)
Connect VCR’s, DVD’s or Video Cameras, etc. here.
DAUDIO1, AUDIO2, AUDIO3
These are audio input terminals.
The input is selectable. Set which video image corresponds
to the audio input from the audio menu screen.
EDVD/HD1
Connect DVD’s, High Definition or Laser Discs, etc.
here.
FDVD/HD2
You can connect DVDs, High Definition sources, Laser
Discs, etc. here.
GPC/RGB (D-Sub)
Connect an analog RGB signal from a computer, etc.
here.
HDVD/HD3, DVD/HD4 (HDMI)
Connect a digital signal from a source with a HDMI
output. See “Specifications” on “Model Information”.
IEXTERNAL CONTROL (D-Sub)
This terminal is used when operating and controlling
the monitor externally with a control system (by RS-
232C).JREMOTE IN
K  REMOTE OUT
Use these terminals to control external equipment.
LHandles
Use when installing or carrying the plasma monitor.
Information
•For Y/Cb/Cr, connect to the DVD1 or DVD2
terminals.
•For SCART, this unit provides two ways to connect:
·SCART1: Connect R/G/B to the DVD/HD1
terminals and composite sync. to the VIDEO1
terminal.
·SCART2: Connect R/G/B + composite sync. to the
PC/RGB terminal.
 
						

							En-10
q POWER ON/STANDBY
Switches the power on/standby.
(This does not operate when the ON/STANDBY
indicator of the plasma is off.)
w OFF TIMER
Activates the off timer for the unit.
eDISPLAY
Displays the source settings on the screen.
rWIDE
Automatically detects the signal and sets the aspect
ratio.
WIDE button is not active for all signals.
tMENU/ENTER
Press this button to access the OSM controls.
Press this button during the display of the main menu
to go to the sub menu.
yCURSOR ( / 
 / 

 / )
Use these buttons to select items or settings and to
adjust settings or switch the display patterns.
uEXIT
Press this button to exit the OSM controls in the main
menu. Press this button during the display of the sub
menu to return to the previous menu.iMUTE
Mutes the audio.
oVOLUME (+ /–)
Adjusts the audio volume.
!0ZOOM (+ /–)
Enlarges or reduces the image.
!1SINGLE
Cancels the split screen mode.
!2SIDE BY SIDE
Press this button to show a couple of pictures in the
side-by-side mode.
!3PICTURE IN PICTURE
Press this button to show a couple of pictures in the
picture-in-picture mode.
!4ACTIVE SELECT
Press this button to make the desired picture activate
during split screen mode.
When the PICTURE FREEZE function is operating,
this button can be used to display still images on the
sub screen.
!5VIDEO1, 2
Press this button to select VIDEO as the source.
VIDEO can also be selected using the INPUT/EXIT
button on the monitor.
!6DVD/HD1, 2, 3, 4
Press this button to select DVD/HD as the source.
DVD/HD can also be selected using the INPUT/EXIT
button on the monitor.
!7PC/RGB
Press this button to select PC/RGB as the source.
PC/RGB can also be selected using the INPUT/EXIT
button on the monitor.
!8PICTURE MEMORY
Switches sequentially between picture memory settings
1 to 6.
!9Remote control signal transmitter
Transmits the remote control signals.
Remote Control
 
						

							En-11
Basic Operations
POWER
To turn the unit ON and OFF:
1. Plug the power cord into an active AC power outlet.
2. Press the Power button (on the unit).
The monitor’s ON/STANDBY indicator turns red and the
standby mode is set.
3. Press the POWER ON button (on the remote control) to
turn on the unit.
The monitor’s ON/STANDBY indicator will light up
(green) when the unit is on.
4. Press the POWER STANDBY button (on the remote
control) or the Power button (on the unit) to turn off the
unit.
The monitor’s ON/STANDBY indicator turns red and the
standby mode is set (only when turning off the unit with
the remote control).
VOLUME
To adjust the sound volume:
1. Press and hold the VOLUME  button (on the remote
control or the unit) to increase to the desired level.
2. Press and hold the VOLUME 
 button (on the remote
control or the unit) to decrease to the desired level.
MUTE
To mute the audio:
Press the MUTE button on the remote control to mute the
audio; press again to restore.
DISPLAY
To check the settings:
1. The screen changes each time the DISPLAY button is
pressed.
2. If the button is not pressed for approximately three seconds,
the menu turns off.
DIGITAL ZOOM
Digital zoom specifies the picture position and enlarges
the picture.
1. (Be sure ZOOM NAV is off.)
Press the ZOOM (+ or -) button to display magnifying
glass. ( 
  )
To change the size of the picture:
Press the ZOOM+ button and enlarge the picture.
A press of the ZOOM- button will reduce the picture
and return it to its original size.
To change the picture position:
Select the position with the 


  buttons.
2. Press the EXIT button to delete the pointer.
OFF TIMER
To set the off timer:
The off timer can be set to turn the power off after 30, 60,
90 or 120 minutes.
1. Press the OFF TIMER button to start the timer at 30
minutes.
2. Press the OFF TIMER button to the desired time.
3. The timer starts when the menu turns off.
→ 30 → 60 → 90 → 120 → 0
OFF TIMER   30
To check the remaining time:
1. Once the off timer has been set, press the OFF TIMER
button once.
2. The remaining time is displayed, then turns off after a few
seconds.
3. When five minutes remain the remaining time appears
until it reaches zero.
OFF TIMER   28
To cancel the off timer:
1. Press the OFF TIMER button twice in a row.
2. The off timer is canceled.
OFF TIMER     0
Note:
After the power is turned off with the off timer ...
A slight current is still supplied to the monitor. When you
are leaving the room or do not plan to use the system for a
long period of time, turn off the power to the monitor.
 
						

							En-12
Wide Screen Operation (manual)
With this function, you can select one of seven screen sizes.
When viewing videos or digital video discs
1. Press the WIDE button on the remote control.
2.Within 3 seconds ...
Press the WIDE button again.
The screen size switches as follows:
→ NORMAL → ANAMORPHIC → STADIUM → ZOOM → 2.35:1 → 14:9 → UNDERSCAN
When a 720P or 1080I signal is input:
ANAMORPHIC ↔  2.35:1
When displaying enhanced split screen:
NORMAL ↔  ANAMORPHIC
NORMAL size screen (4:3)
The normal size screen is displayed.
* The picture has the same size as video pictures with a 4 : 3
aspect ratio.
ANAMORPHIC size screen
The image is expanded in the horizontal direction.
* Images compressed in the horizontal direction (“squeezed
images”) are expanded in the horizontal direction and
displayed on the entire screen with correct linearity.
(Normal images are expanded in the horizontal direction.)
STADIUM size screen
The picture is expanded in the horizontal and vertical
directions at different ratios.
* Use this for watching normal video programs (4:3) with a
wide screen.
ZOOM size screen
The picture is expanded in the horizontal and vertical
direction, maintaining the original proportions.
* Use this for theater size (wide) movies, etc.
2.35:1 size screen
The squeezed film image is expanded to fulfill the entire
screen at a ratio of 2.35:1. Black bands do not appear at
the top and bottom but information is lost on the left and
right margins.
•This feature is available when the input signal is video,
component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB
(525P or 625P signal from a scan converter).
* If black bands appear on the top and bottom in the full size
screen, select the 2.35:1 size screen to fill the screen and
avoid image retention.
14:9 size screen
The image is displayed at a 14:9 aspect ratio.
* This feature is available when the input signal is video,
component (480I, 480P, 576I, 576P) or RGB (525P or 625P
signal from a scan converter).
UNDERSCAN size screen
Set “UNDERSCAN” to “ON” in the “IMAGE ADJUST”.
Typical televisions crop the image (i.e., overscan). In order
to restore the entire image, select UNDERSCAN.
* Picture noise or black border may appear near the edge of
screen depending on the connected component.
* The continuous display in this screen size over a prolonged
period of time may result in image retention.
* When Macrovision signal is input, the brightness may
change.
Note:
Do not allow 4:3 content to be displayed for extended
periods of time without using gray bars. This can cause
image retention.
WIDE Operations
Information is lost on both sides.Original image

Overscan
Underscan
 
						

							En-13
Information
 Supported resolution
See page En-3 of Model Information for details on the
display output of the various VESA signal standards
supported by the monitor.
 When 852 (848) dot  480 line wide VGA*
signals with a vertical frequency of 60 Hz and
horizontal frequency of 31.7 (31.0) kHz are in-
put
Select an appropriate setting for RGB SELECT mode
referring to the“Table of Signals Supported” on page
En-3 of Model Information.
*“VGA”, “SVGA” and “SXGA” are registered
trademarks of IBM, Inc. of the United States.
Note:
Do not allow 4:3 content to be displayed for extended
periods of time without using gray bars. This can cause
image retention.
Wide Screen Operation with
Computer Signals
Switch to the wide screen mode to expand the 4 : 3 image
to fill the entire screen.
1. Press the WIDE button on the remote control.
2.Within 3 seconds ...
Press the WIDE button again.
The screen size switches as follows:
→ NORMAL → ANAMORPHIC → ZOOM
When displaying enhanced split screen:
NORMAL ↔  ANAMORPHIC
NORMAL size screen (4:3 or SXGA 5:4)
The picture has the same size as the normal computer
image.
ANAMORPHIC size screen
The image is expanded in the horizontal direction.
ZOOM size screen
When wide signals are input.
ANAMORPHIC size screen
 
						

							En-14
Information
Split screen operations may not function depending on
the combination of input signals. In the table below,
“” means Yes, “” means No.
 Split screen operations may not function
depending on the frequency of the RGB
signals.
SPLIT SCREEN Operations
Showing a couple of pictures on the
screen at the same time
* There may be some RGB-input  signals that may not be
displayed as not all signals are supported.
1. Press the button to select a screen mode from among single
mode, side-by-side, and picture-in-picture.
Note:
Picture A and B on the above screen are not always of the
same height.
Operations in the Side-by-side mode
To change the picture size, press the cursor 
  or 
button.
To swap the picture on the right and the left, press the
cursor 
	 button.
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
BA
To  make the desired picture active, press the ACTIVE
SELECT button.
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
ACTIVE SELECT
button
	 
button
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
BA
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
BA
Side-by-Side2-R
Side-by-Side1 Side-by-Side2-L
Side-by-Side4-R
Side-by-Side3 Side-by-Side4-L

button
button

button
button

button
button

button
button
buttonbuttonbuttonbuttonbuttonbutton
VIDEO1
Sub 
screenMain screen
PC/RGB
A
VIDEO1
VIDEO1PC/RGB
AB
SIDE BY SIDE
buttonPICTURE IN PICTURE
buttonSINGLE
button
PICTURE IN
PICTURE
button
SINGLE
button
SIDE BY SIDE
button
VIDEO1VIDEO2DVD/HD1DVD/HD2DVD/HD3DVD/HD4SCART1SCART2
PC/RGB
VIDEO1

VIDEO2

DVD/HD1

DVD/HD2

PC/RGB

Pictures
displayed on
the left/sub
screen
(Select2)
Pictures displayed on the right/main screen (Select1)DVD/HD3

DVD/HD4

SCART1

SCART2

 
						

							En-15
Operations in the Picture-in-picture mode
To move the position of the sub screen, press the cursor 

or  button.
To change the size of the sub screen, press the 
 button.
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
 button
 button
 button
 button
To make the desired picture active, press the ACTIVE
SELECT button.
ACTIVE
SELECT
button
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
A
B
VIDEO1PC/RGBVIDEO1A
B
PC/RGB
Bottom Left Bottom Right

button
button
 button
 button
Top Right

button
button
 button
 button
Top Left
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
Selecting the input signals to be displayed
1. Press the ACTIVE SELECT button to make the desired
picture active.
2. Press the PC/RGB, VIDEO1, 2 or DVD/HD1, 2, 3, 4
button to change the selection of the input signal.
The INPUT/EXIT button on the monitor can also be used
to change the selection.
Zooming in on a specific input
1. Press the ACTIVE SELECT button to make the desired
picture active.
2. Use the ZOOM (
 or ) button to enlage the picture.
For details, see “DIGITAL ZOOM” on page En-11.
Adjusting the OSM controls
1. Press the ACTIVE SELECT button to make the desired
picture active.
2. Press the MENU/ENTER button to display the MAIN
MENU.
3. Adjust the setting to your preference.
For details, see “OSM (On Screen Menu) Controls” on
page En-16.
Note:
During enhanced split screen, some functions of OSM
controls are not available.
 
						

							En-16
Menu Operations
The following describes how to use the menus and the
selected items.
1. Press the MENU/ENTER button on the remote control to
display the MAIN MENU.
MAIN MENU
PICTURE
AUDIO
IMAGE ADJ.SET UP
FUNCTION
SIGNAL INFO.
SEL.EXITMENU/ENTEROKEXIT
2. Press the cursor buttons 
   on the remote control to
highlight the menu you wish to enter.
3. Press the MENU/ENTER button on the remote control to
select a sub menu or item.
SEL. ADJ. RETURN
PICTURE
PICTURE MEMORY
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
NR
COLOR TEMP.
CINEMA MODE
PICTURE MODE:   OFF
:   OFF
:   MIDDLE 
:   ON
:   NORMAL: 52
: 32
: 16
: 32
: 32
MENU/ENTEROK
GR
EXIT
4. Adjust the level or change the setting of the selected item
by using the cursor buttons 

   on the remote control.
CONTRAST:
 10
5. The adjustments or settings are then stored in memory.
The change is stored until another change is made.
6. Repeat steps 2 – 5 to adjust an additional item, or press
the EXIT button on the remote control to return to the
main menu.
* When adjusting using the bar at the bottom of the screen,
press the 

 or  button within 5 seconds. If not, the current
setting is stored and the previous screen appears.
Note: The main menu disappears by pressing the EXIT
button.
OSM (On Screen Menu) Controls
Information
 Advanced menu mode
When “ADVANCED OSM” is set to “ON” in the
FUNCTION menu, full menu items will be shown.
SEL. ADJ. RETURN
PICTURE
PICTURE MEMORY
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
NR
COLOR TEMP.
CINEMA MODE
PICTURE MODE
GAMMA
LOW TONE
SET UP LEVEL
COLOR TUNE:   OFF
:   OFF
:   MIDDLE
:   ON
:   NORMAL
:   2.2
:   MODE1
:   0%: 52
: 32
: 16
: 32
: 32
MENU/ENTEROK
GR
EXIT
* The actual screen may be different from the ones in
this manual.
 
						

							En-17
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
PICTURE PICTURE MEMORY OFF/MEMORY1-6 YES En-19
CONTRAST←→  0←52→72 YES En-19
BRIGHTNESS←→  0←32→64 YES En-19
SHARPNESS←→  0←16→32 YES En-19
COLOR←→  0←32→64 YES En-19
TINT R←→G     0←32→64 YES En-19
NR OFF/NR-1/NR-2/NR-3 YES En-19
COLOR TEMP. LOW/MIDDLE LOW/MIDDLE/HIGH YES En-20
WHITE BALANCE GAIN RED←→  0←40→70 YES En-20
GAIN GREEN←→  0←40→70 YES En-20
GAIN BLUE←→  0←40→70 YES En-20
BIAS RED←→  0←40→70 YES En-20
BIAS GREEN←→  0←40→70 YES En-20
BIAS BLUE←→  0←40→70 YES En-20
RESET OFF←→ON YES En-20
CINEMA MODE ON←→OFFYES En-20
PICTURE MODE DEFAULT/THEATER1/THEATER2/NORMAL/BRIGHT YES En-20
GAMMA 2.1←→2.2←→2.3←→2.4 YES En-21
LOW TONE *
3MODE1←→MODE2 YES En-21
SET UP LEVEL 0%←→3.75%←→7.5% YES En-21
COLOR TUNE RED Y←→M0←32→64 YES En-21
GREEN C←→Y0←32→64 YES En-21
BLUE M←→C0←32→64 YES En-21
YELLOW G←→R0←32→64 YES En-21
MAGENTA R←→B0←32→64 YES En-21
CYAN B←→G0←32→64 YES En-21
RESET OFF←→ON YES En-21
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
AUDIO BASS←→0←13→26 YES En-22
TREBLE←→0←13→26 YES En-22
BALANCE L←→R -22←0→+22 YES En-22
AUDIO INPUT1 VIDEO 1-2 / DVD/HD 1-4 / PC/RGB YES En-22
AUDIO INPUT2 VIDEO 1-2 / DVD/HD 1-4 / PC/RGB YES En-22
AUDIO INPUT3 VIDEO 1-2 / DVD/HD 1-4 / PC/RGB YES En-22
DVD/HD3 INPUT INPUT 1-3 / HDMI YES En-22
DVD/HD4 INPUT INPUT 1-3 / HDMI YES En-22
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
IMAGE ADJ. ASPECT MODE ZOOM/NORMAL/ANAMORPHIC/STADIUM/14:9/2.35:1/UNDERSCAN — En-22
V-POSITION←→-64←0→+64 YES En-22
H-POSITION←→-128←0→+127 YES En-22
V-HEIGHT←→0←→64 YES En-22
H-WIDTH←→0←→64 YES En-22
AUTO PICTURE ON←→OFF*
2NO En-22
FINE PICTURE*1←→*20←→64 YES En-22
PICTURE ADJ.*1←→*20←→64 YES En-22
UNDERSCAN ON←→OFFYES En-22
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
SET UP LANGUAGEENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/
У/EΛΛHNIKA/PORTUGUÊS/TÜRKÇENO En-23
DVD/HD1 INPUT COMPONENT←→SCART1 YES En-23
D-SUB INPUT RGB←→SCART2 YES En-23
HD SELECT 1080I/1035I/540P NO En-23
RGB SELECT AUTOYES En-24
HDMI SET UP LOW←→HIGH NO En-24
COLOR SYSTEM AUTO/3.58NTSC/4.43 NTSC/PAL/PAL 60/PAL-N/PAL-M/SECAM NO En-24
BACK GROUND BLACK/GRAYYES En-24
GRAY LEVEL 0←…
→3←…
→15 YES En-25
S1/S2 AUTO←→OFFYES En-25
DISPLAY OSM ON←→OFFYES En-25
OSM ADJ. TOP LEFT←→TOP CENTER←→TOP RIGHT←→BTM LEFT←→BTM CENTER←→BTM RIGHT YES En-25
REMOTE ID ALL←→1←…
→4 YES En-26
ALL RESET ON←→OFF— En-26
 : Shaded areas indicate the default value.
←→
: Press the 
 or  button to adjust.
 : Menu items in a ruled box are available when the ADVANCED OSM is set to ON.
Menu Tree
 
						

							En-18
*1 Only when AUTO PICTURE is OFF.
*2 PC/RGB only
*3“LOW TONE” is only for 50 inch type.
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
FUNCTION ADVANCED OSM ON←→OFFYES En-26
POWER MGT. ON←→OFFYES En-26
INPUT SKIP ON←→OFFYES En-27
SUB. PICTURE SUB. P DETECT OFF←→AUTO YES En-27
DISPLAY FADE←→NORMAL YES En-27
SUB. P RATE 20%←…
→100% YES En-27
ZOOM NAV OFF←→S BY S←→BTM LEFT←→BTM RIGHT←→TOP RIGHT←→TOP LEFT YES En-27
PICTURE FREEZE OFF←→S BY S1←→S BY S2←→BTM LEFT←→BTM RIGHT←→TOP RIGHT←→TOP LEFT YES En-28
PDP SAVER MANUAL/AUTO PEAK BRIGHT 100%/75%/50%/25% YES En-28
ORBITER OFF/AUTO1/AUTO2 YES En-29
INVERSE/WHITE OFF/INVERSE/WHITE YES En-29
SCREEN WIPER ON/OFF YES En-29
SOFT FOCUS OFF/LEVEL1-4 YES En-29
OSM ORBITER ON/OFF YES En-29
OSM CONTRAST LOW/NORMAL YES En-30
PWR. ON MODE INPUT LAST / VIDEO 1-2 / DVD/HD 1-4 / PC/RGB / MULTI YES En-30
VOLUME LAST←→0←…
→42 YES En-30
PROTOCOL SET ON←→OFFYES En-30
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
SIGNAL INFO.—En-30
Information
 Restoring the factory default settings
Select “ALL RESET” under the SET UP menu. Note that this also restores other settings to the factory defaults.