NEC Projector VE303 User Manual

24
Connecting the Projector
	Make sure that the power plug is fully inserted into both the projector AC IN terminal and the wall outlet. E62405SP
R
Connect to Computer/Notebook
1.........................................................................\
....................Power cord (supplied)2.........................................................................\
......................................HDMI cable3........................................................................Computer cable...

25
	Due to the difference in applications for each country, some regions may have different accessories.
	When Deep Color is set to ON on your HDMI equipment, video or audio noise may be generated depending on the equipment or cable being used. Should this happen, set Deep Color to OFF (8 bit). 
Connect to Video Sources
	Make sure that the power plug is fully inserted into both the projector AC IN terminal and the wall outlet.
1.........................................................................\...

26
Powering On/Off the Projector
	Turn on the projector first and then the signal sources.
POWER/STANDBY 1
	When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select the menu languages. To select the language, 
use the , , 
, or  button on the remote control. Select your language. Please see page 48.
 	While the POWER LED indicator is blinking green in short cycles, the power cannot be turned off by using the “POWER OFF” button.
Powering On the...

27
Powering Off the Projector
1.    Press the “POWER OFF” button on the remote control or the  
 button on the control panel to turn off the projector lamp, 
you will see a message as below on the on-screen display.
 
ARE YOU SURE ?
YES NO
POWER OFF
2.   Press the “POWER OFF” button again to confirm. 
3.   
Disconnect the power cord from the electrical outlet and the 
projector. If you disconnect the power cord while viewing 
the picture and connect the power cord again, wait for at 
least one second...

28
Warning Indicator
   When the “STATUS” LED indicator flashes red, it 
indicates the projector has overheated. The projector will 
automatically shut itself down.
WARNING! TEMPERATURE TOO HIGH
1. MAKE SURE AIR IN AND OUTLETS ARE NOT BLOCKED.
2.MAKE SURE THE ENVIRONMENT TEMPERATURE IS UNDER 40 DEGREE C
    When the “LAMP” LED indicator turns red and the message 
below displays on-screen, the projector has detected that 
the lamp is approaching its end of life. When you see this 
message, change the...

29
Adjusting the Projected Image
Adjusting the Height of Projection Image
The projector is equipped with tilt feet to raise and lower the 
image to fill the screen.
1.  Locate the tilt foot you wish to modify on the underside of 
the projector. 
2.  Rotate the tilt foot clockwise to raise the projector or 
counter-clockwise to lower it. Repeat with the remaining 
feet as necessary.
Tilt foot (rear)Tilt foot (rear)Tilt foot (front) 
... English 
Installation  

30
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear. 
To zoom the image, turn the zoom lever in or out.
Focus Ring
Zoom Lever 
English ... 
Installation  

31
Adjusting Projection Image Size (Diagonal)
Projection Image Size from 30” to 300” (0.76 to 7.62 meters).
(B)
(D)
(C)
()
D)(D)
()
Screen Width
Screen Diagonal
Screen Center
Screen Bottom
Lens Center 
Screen Height
B = Vertical distance between lens center and screen centerC = Throw distanceD = Vertical distance between lens center and bottom of screen(top of screen for ceiling application)
α = Throw angle
Note: Distances may vary ±5%.
Screen Size(B)(C)D (WIDE)
α
DiagonalWidthHeightWideTeleWideTele...

32
Screen Size(B)(C)D (WIDE)
α
DiagonalWidthHeightWideTeleWideTele
inchmminchmminchmminchmminchmminchmminchmmdegreedegree
90228672182954137235891 140 3566 155 3932 8 206 14.0 12.8 
100254080203260152439990 156 3962 172 4368 9 228 14.0 12.8 
1203048962438721829471188 187 4754 206 5242 11  274 14.0 12.8 
15038101203048902286581486 234 5943 258 6553 13 343 14.0 12.8 
180457214436581082743701783 281 7131 310 7863 16 411 14.0 12.8 
200508016040641203048781981 312 7923 344 8737 18 457 14.0 12.8...

33
The Projector has a multilingual On Screen Display that 
allows you to make image adjustments and change a variety of 
settings.
How to operate 
1. To open the OSD, press the MENU button on the remote control.
2.  When OSD is displayed, use the     buttons to select any item 
in the main menu. While making a selection on a particular page, 
press the  button to enter sub menu.
3.  Use the     buttons to select the desired item in the sub menu 
and adjust the settings by using the     button. 
4....