NEC Projector V302X User Manual

24English ...
Introduction
Viewing 3D Images
The projector provides 3D images to a user wearing commercially 
available LCD shutter eyeglasses.
CAUTION
Health precautionsBefore viewing, be sure to read health care precautions that may be found in the user’s manual included with your LCD shutter eyeglasses or your 3D compatible content such as DVDs, video games, computer’s video files and the like.To avoid any adverse symptoms, heed the following:- Do not use LCD shutter eyeglasses for viewing any...

25... English
Installation
Connecting the Projector
	Make sure that the power plug is fully inserted into both the projector AC IN termi-nal and the wall outlet. 
	The MONITOR OUT connector supports Separate sync signal only.
Connect to Computer/Notebook
1.........................................................................\
....................Power cord (supplied)2.........................................................................\
......................................HDMI...

26English ...
Installation
1.........................................................................\
....................Power cord (supplied)2.........................................................................\
......................................HDMI cable3........................................................................Computer cable (VGA) (supplied)4.........................................................................\
.......................................RS232...

27... English
Installation
	Due to the difference in applications for each country, some regions may have different accessories.
	When Deep Color is set to ON on your HDMI equipment, video or audio noise may be generated depending on the equipment or cable being used. Should this happen, set Deep Color to OFF (8 bit). 
Connect to Video Sources
	Make sure that the power plug is fully inserted into both the projector AC IN termi-nal and the wall outlet....

28English ...
Installation
1.........................................................................\
....................Power cord (supplied) 2.........................................................................\
....................................HDMI cable*3....................................................15-Pin to 3 RCA Component/HDTV Adaptor4.........................................................................\...

29... English
Installation
Powering On/Off the Projector
Turn on the projector first and then the signal sources.
(*)When “Normal” is selected for “Standby Mode”, the Power LED indicator will turn red; when “Network standby” is selected for “Standby Mode”, the Power LED indicator will turn orange.
POWER/STANDBY 1
	When you first turn on the projec-tor, you will get the Startup menu. This menu gives you the opportunity to select the menu languages. To select the language, 
use the , , 
, or  button on...

30English ...
Installation
Powering Off the Projector
1.    Press the “POWER OFF” button on the remote control or the 
 button on the control panel to turn off the projector lamp, 
you will see a message as below on the on-screen display.
 
ARE YOU SURE
YES NO
POWER OFF
2.   Press the “POWER OFF” button again to confirm. 
3.   
Disconnect the power cord from the electrical outlet and the 
projector. If you disconnect the power cord while viewing 
the picture and connect the power cord again, wait for at...

31... English
Installation
Warning Indicator
   When the “STATUS” LED indicator flashes red, it 
indicates the projector has overheated. The projector will 
automatically shut itself down.
WARNING! TEMPERATURE TOO HIGH
1. MAKE SURE AIR IN AND OUTLETS ARE NOT BLOCKED.
2. MAKE SURE THE ENVIRONMENT TEMPERATURE IS UNDER 40 DEGREE C
    When the “LAMP” LED indicator turns red and the message 
below displays on-screen, the projector has detected that 
the lamp is approaching its end of life. When you see...

32English ...
Installation
Adjusting the Projected Image
Adjusting the Height of Projection Image
The projector is equipped with the tilt foot for adjusting the 
image height.
1.  Press the tilt foot release button. 1
    Keep to press the tilt foot release button for raising or 
lowering the projector, then lock the button by releasing it. 2
2.  Rotate the rear feet counter clockwise to raise the projector 
or clockwise to lower it. 3
Rear footRear foot
Tilt footrelease button
Tilt Foot32
1
3
Two tilt...

33... English
Installation
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear. 
To zoom the image, turn the zoom lever in or out.
Focus Ring
Zoom Lever