NEC Projector UM301W User Manual

30
3. Convenient Features
7. Use the ▲▼◀▶ button to move the projected image frame as shown on the example.
8.  Press the ENTER button.
9.  Use the ▲▼◀▶ button to select another icon which points in the direction.
	 On	the	Cornerstone	adjustment	screen,	select	[EXIT]	or	press	the	EXIT	button	on	the	remote	control.
  The confirmation screen is displayed.
10. Press the ◀ or ▶	button	to	highlight	the	[OK]	and	press	the	ENTER	button.
This	completes	the	Cornerstone	correction.
Selecting	[CANCEL]	will	return...

31
3. Convenient Features
Pincushion
1.	 Press	the	KEYSTONE	button	with	no	menu	displayed.
 The KEYSTONE screen will be displayed.
 
•	 Press	the	KEYSTONE	button	when	using	the	remote	control.
2. Press the 	button 	to	 select	 either	PINCUSHION 	ADJUSTMENT 	LEFT/RIGHT 	or	 PINCUSHION 	ADJUSTMENT 	
TOP/BOTTOM.
 
3. Press either  or  button to reform pincushion distortion.
 
4.	 Press	the	EXIT	when	PINCUSHION	adjustment	is	completed.
NOTE:	
•	 Even	when	the	projector	is	turned	on,	the	last	used...

32
3. Convenient Features
2. Move the cursor onto YES using either  or  button and then press the ENTER.
 
NOTE:
•	 All	adjusted	values	set	in	the	KEYSTONE	adjustment	are	reset	to	initial	values
TIP:
Adjustable	range	of	the	KEYSTONE	and	the	CORNERSTONE:
Horizontal	DirectionVertical	Direction
CORNERSTONEApprox.	±10°	(Max)Approx.	±10°	(Max)KEYSTONE
Adjustable	range	may	be	narrower	depending	on	input	signal. 

33
3. Convenient Features
 Preventing the Unauthorized Use of the Projector [SECURITY]
A	keyword	 can	be	set	 for	your	 projector	 using	the	Menu	 to	avoid	 operation	 by	an	 unauthorized	 user.	When	 a	keyword	
is	 set,	 turning	 on	the	 projector	 will	display	 the	Keyword	 input	screen. 	Unless	 the	correct	 keyword	 is	entered,	 the	pro-
jector	cannot	project	an	image. 	
•	 The	[SECURITY]	setting	cannot	be	cancelled	by	using	the	[RESET]	of	the	menu.
To	enable	the	Security	function:
1. Press the MENU...

34
3. Convenient Features
7. Type in the same combination of  buttons and press the ENTER button.
  The confirmation screen will be displayed.
8.	 Select	[YES]	and	press	the	ENTER	button.
	 The	SECURITY	function	has	been	enabled.
To	turn	on	the	projector	when	[SECURITY]	is	enabled:
1. Press the POWER button.
	 The	projector	will	be	turned	on	and	display	a	message	to	the	effect	that	the	projector	is	locked.
2.  Press the MENU button.
3.  Type in the correct keyword and press the ENTER button. The...

35
3. Convenient Features
To	disable	the	SECURITY	function:
1. Press the MENU button.
  The menu will be displayed.
2.		Select	[SETUP]	→	[INSTALLATION]	→	[SECURITY]	and	press	the	ENTER	button.
  The OFF/ON menu will be displayed.
3.	 Select	[OFF]	and	press	the	ENTER	button.
	 The	SECURITY	KEYWORD	screen	will	be	displayed.
4. Type in your keyword and press the ENTER button.
	 When	the	correct	keyword	is	entered,	the	SECURITY	function	will	be	disabled.
NOTE:	 If	you	 forget	 your	keyword,	 contact	your...

36
3. Convenient Features
 Using the Computer Cable (VGA) to Operate the 
Projector (Virtual Remote Tool)
Using	the	utility	 software	 “Virtual	Remote	 Tool”	included	 on	the	 companion	 NEC	Projector	 CD-ROM,	 Virtual	Remote	
screen	(or	toolbar)	can	be	displayed	on	your	computer	screen.
This	will	help	 you	perform	 operations	 such	as	projector’s	 power	on	or	off	 and	 signal	 selection	 via	the	 computer	 cable	
(VGA),	serial	cable,	 or	LAN	 connection. 	Only	 via	serial	 or	LAN	 connection	 it	is...

37
3. Convenient Features
NOTE:
•	 When	[COMPUTER]	 is	selected	 from	your	source	 selection,	 the	Virtual	 Remote	 screen	or	the	 toolbar	 will	be	displayed	 as	well	 as	
your	computer	screen.
•	 Use	 the	supplied	 computer	 cable	(VGA)	 to	connect	 the	COMPUTER	 IN	terminal	 directly	with	the	monitor	 output	terminal	 of	the	
computer	to	use	Virtual	Remote	Tool.
	 Using	a	switcher	or	other	cables	than	the	supplied	computer	cable	(VGA) 	may	cause	failure	in	signal	communication.
	 VGA	cable	terminal:...

38
3. Convenient Features
TIP:
If	the	menu	window	will	not	be	displayed,	try	the	following	procedure.
For	Windows	7
1.	 Click	“start”	on	Windows.
2.	 Click	 “All	Programs” 	→	“Accessories” 	→	“Run”.
3.	 Type 	your 	CD-ROM 	drive 	name 	(example: 	“Q:\”) 	and 	“LAUNCHER.EXE” 	in 	“Name”. 	(example: 	Q:\
LAUNCHER.EXE)
4.	 Click	 “OK”.
 The menu window will be displayed.
2	 Click	 “Install	Virtual	Remote	 Tool”	on	the	menu	window.
 The installation will start.
 When the installation is complete, the Welcome...

39
3. Convenient Features
TIP:
Uninstalling	Virtual	Remote	 Tool
Preparation:
Exit	Virtual	 Remote	 Tool	before	 uninstalling. 	To	 uninstall	 Virtual	Remote	 Tool,	the	Windows	 user	account	 must	have	
“Administrator” 	privilege	 (Windows	 8.1,	Windows	 8,	Windows	 7	and	 Windows	 Vista)	or	“Computer	 Administrator” 	
privilege	(Windows	XP).
•	For	Windows	8.1, 	Windows	8, 	Windows	7	and	 Windows	Vista
1	 Click	“Start”	and	then	 “Control	Panel”.
 The Control Panel window will be displayed.
2	 Click...