NEC Projector Um280wi User Manual

101
5. Using On-Screen Menu
[VERSION]
[FIRMWARE]	Version
[DATA]	Version
[OTHERS]
[PROJECTOR	NAME]
[MODEL	NO.]
[SERIAL	NUMBER]
[LAN	UNIT	 TYPE]
[CONTROL	ID]	(when	[CONTROL	ID]	is	set) 

102
5. Using On-Screen Menu
 Menu Descriptions & Functions [RESET]
Returning to Factory Default [RESET]
The	RESET	 feature	allows	you	to	change	 adjustments	 and	settings	 to	the	 factory	 preset	for	a	(all)	 source	 (s)	except	
the	following:
[CURRENT	SIGNAL]
Resets	the	adjustments	for	the	current	signal	to	the	factory	preset	levels. 	
The	items	 that	can	be	reset	 are:	[PRESET],	 [CONTRAST],	 [BRIGHTNESS],	 [COLOR],	[HUE],	[SHARPNESS],	
[ASPECT	RATIO],	[HORIZONTAL],	[VERTICAL],	[CLOCK],	[PHASE],	and...

103
1 Setting Up the Screen and the Projector
[UM330X/UM280X]
The	further	 your	projector	 is	from	 the	screen	 or	wall,	 the	larger	 the	image. 	The	 minimum	 size	the	image	 can	be	is	61.5"	
(1562	 mm)	measured	 diagonally	 when	the	projector	 is	4	inches	 (105	mm)	between	 the	screen	 side	of	the	 projector	
and	the	wall	or	screen. 	The	largest	the	image	can	be	is	116.6"	(2962	mm)	when	the	projector	is	20	inches	(510	mm)	
between	the	screen	side	of	the	projector	and	the	wall	or	screen....

104
6. Installation and Connections
[UM330W/UM280W]
The	further	 your	projector	 is	from	 the	screen	 or	wall,	 the	larger	 the	image. 	The	 minimum	 size	the	image	 can	be	is	58"	
(1473	 mm)	measured	 diagonally	 when	the	projector	 is	4	inches	 (105	mm)	between	 the	screen	 side	of	the	 projector	
and	 the	wall	 or	screen. 	The	 largest	 the	image	 can	be	is	110"	 (2794	 mm)	when	 the	projector	 is	20	 inches	 (510	mm)	
between	the	screen	side	of	the	projector	and	the	wall	or	screen....

105
6. Installation and Connections
WARNING
*	 Installing	your	projector	 on	the	 ceiling	 must	be	done	
by	a 	qualified 	technician. 	Contact 	your 	NEC 	dealer 	for	
more	information.
*	 Do	not	attempt	to	install	the	projector	yourself.
•	 Only	 use	your	 projector	 on	a	solid,	 level	surface. 	If	 the	
projector	 falls	to	the	 ground,	 you	can	 be	injured	 and	
the	projector	severely	damaged.
•	 Do	not	use	 the	projector	 where	temperatures	 vary	
greatly.	The	 projector	 must	be	used	 at	temperatures...

106
6. Installation and Connections
 Making Connections
NOTE:	When	using	with	a	notebook	 PC,	be	sure	 to	connect	 the	projector	 and	notebook	 PC	while	 the	projector	 is	in	 standby	 mode	
and	before	turning	on	the	power	to	the	notebook	PC.
In	most	cases	the	output	signal	from	the	notebook	PC	is	not	turned	on	unless	connected	to	the	projector	before	being	powered	up.
*	 If	the	screen	 goes	blank	 while	using	 your	remote	 control,	 it	may	 be	the	 result	 of	the	 computer’s	 screen-saver	 or	power...

107
6. Installation and Connections
•	 Select	the	source	name	for	its	appropriate	input	connector	after	turning	on	the	projector.
Input	connectorSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN	COMPUTER(COMPUTER	1)
HDMI	1	IN	HDMI1(HDMI*)
HDMI	2	IN	HDMI2(HDMI*)
USB	(PC)	USB	DISPLAY(USB	DISPLAY)
*	 The	HDMI	button	 on	the	 remote	 control	will	toggle	 between	 “HDMI1	and	HDMI2”. 	Upon	 the	first	 button	 push	the	
projector	 will	always	 switch	to	HDMI	 1	IN. 	A	 second...

108
6. Installation and Connections
Connecting an External Monitor
You	can	connect	 a	separate,	 external	monitor	to	your	 projector	 to	simultaneously	 view	on	a	monitor	 the	computer	
analog	image	you’re	projecting.
NOTE:
•	 Daisy	chain	connection	is	not	possible.
•	 When	audio	equipment	is	connected,	the	projector	speaker	is	disabled.
Computer cable (VGA) 
(supplied) Stereo mini-plug audio cable (not 
supplied)
Computer cable (VGA) 
(not supplied)
Stereo mini-plug audio 
cable (not supplied) 

109
6. Installation and Connections
Connecting Your DVD Player or Other AV Equipment
Connecting	Video/S-Video	Input
•	 Select	the	source	name	for	its	appropriate	input	connector	after	turning	on	the	projector.
Input	connectorSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
VIDEO	IN	VIDEO(VIDEO)
S-VIDEO	IN	S-VIDEO(S-VIDEO)
NOTE:	The	AUDIO	IN	L	and	R	jacks	(RCA)	are	shared	between	the	Video	and	S-Video	inputs.
NOTE:	Refer	to	your	VCR	owner’s	manual	for	more	information	about	your...

110
6. Installation and Connections
Connecting Component Input
	 A	component	 signal	will	be	automatically	 displayed.	If	 not,	 from	 the	menu,	 select	[SETUP]	→	[OPTIONS(1)]	→ 
[SIGNAL	SELECT]	→	[COMPUTER],	and	then	place	a	check	mark	in	the	Component	radio	button.
•	 Select	the	source	name	for	its	appropriate	input	connector	after	turning	on	the	projector.
Input	connectorSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN	COMPUTER(COMPUTER	1)
NOTE:	Refer	to	your	DVD...