NEC Projector Sx4000d User Manual

E – 4
INPUT3RGB R/Cr
G/Y
B/Cb
H/HV
VR/Cr Cr
Y G/Y
B/Cb Cb
H/HV
V
OPTIONIN
OUT
REMOTE1
REMOTE2
INPUT7 INPUT8INPUT5
S-VIDEO1
Y
C
S-VIDEO2 VIDEO1 VIDEO2INPUT6
IN
OUT
INPUT2 INPUT1 INPUT4
56
1
2
3
4
910
8 7
1. INPUT 3 RGB Connector (Mini D-Sub 15 pin)
Connect your PC or other analog RGB equipment such as a high-defi-
nition document camera.
2. Option Connector (Mini D-Sub 9 pin)
For system expansion such as PC-control.
IN ................. connect to the external equipment such as PC.
OUT ............. for...

E – 5
OUTPUT OUTPUT
RGBDIGITAL
INPUT9 INPUT 0
SDI
11
aaaaaaaaaaaaaaaaaaaaaaa
11. RGB Digital Input/Output Connectors (DVI-D 24 pin)
These connectors are used for double or triple stacking.
Use the supplied DVI-D cable to connect the OUTPUT terminal of the
first projector to the second projectors INPUT until all the projectors
are connected.Push the left side of the panel to open the compartment for the
RGB Digital connectors and the optional SDI board.
Space to install the optional SDI or SX
HDSDI...

E – 6
OFF
+-
PICTUREADJUSTABC DEFGHI
JKL MNO PQR
STU
,.
UNDO CANCEL
TEST
PICTUREKEYSTONE AMPLITUDE ENTRYLISTSOUND OSD
MUTE
MAGNIFYHELP INFO.
POSITION AUTOPIXELVWX YZ/
WHITE BAL.IMAGE
ON POWER
MENU
ENTER
123
456
7
089
ADDRESS
PROJECTOR
RGB
LENS
SHUTTER
BS
+
-
+
-
FOCUSZOOM
CTLLENS
2
5
6
7
9
10
12
13
17
20
21
22
24
262
5
23
19
18
16
15
14
11 8 4 3 1
Remote Control
1 POWER ON
Press to turn on the projector. The POWER indicator lights up green.
2 POWER OFF
Press and hold this button for a minimum of two...

E – 7
17 POSITION
Press to display the Blanking  screen; press again to display the Posi-
tion screen.
While pressing and holding CTL, pressing this button displays the Lens
Shift adjustment screen.
18 MUTE SOUND
(available only when using with the ISS -6020 or IPS4000)
Turns off the sound for a short period of time. Press again to restore the
sound.
19 MUTE OSD
Press to turn off the on-screen display. Press again to restore the on-
screen display.
NOTE: You can also turn off the on-screen display by...

E – 8
2. INSTALLATION
Formulas: Screen Width H (5:4) (m) = Screen Height V x 5/4 x 0.0254
Screen Height V (5:4) (m) = Screen Width H x 4/5 x 0.0254
Screen Diagonal (5:4) (m) = Screen Height V x 6.4/4 x 0.0254
Screen Width H (5:4) (inch) = Screen Height V x 5/4
Screen Height V (5:4) (inch) = Screen Width H x 4/5
Screen Diagonal (5:4) (inch) = Screen Height V x 6.4/4
Width (H)
1.6(63)
1.9(75)
2.3(90)
2.9(112.5)
3.4(135)
4.0(157.5)
4.6(180)
5.1(202.5)
5.7(225)
6.7(262.5)
7.6(300)
8.6(337.5)
9.5(375)Height...

E – 9
Lens Shift Adjustable Range
Lens Shift Adjustable Range for Desktop and Ceiling Mount Application
The diagram below shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown using the normal
projection position as a starting point.
Maximum Possible Range for TL-1Z/1ZH, TL-2Z and TL-4Z
Parenthesized values for the ceiling mount application
Up: 0.41 V (0.24 V) Right: 0.28 H (0.19 H)
Down: 0.24 V (0.41 V) Left: 0.19 H (0.28 H)
(H: width of projected...

E – 10
Pulling Out the Handles
Pull out the handle until it clicks into place.
Retracting the Handles
1) Push the lever to unlock and  2) retract the handle.
Selecting A Location
The further your projector is from the screen or wall, the larger the im-
age. The minimum size the image can be projected is 80 (2 m) mea-
sured diagonally. The largest the image can be is 500 (12.7 m).
WARNING
•Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the...

E – 11
O
F
F
 P
O
W
E
R
 O
N
Connecting the Power Cable and Turn
on the Projector
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
1. Connect the supplied power cable to the projector.
Plug the supplied power cable into the AC outlet.
3. BASIC OPERATION
2. Turn On The Projector
The main power switch is on the rear panel of the projector.
By turning this switch on, the projector will go into its standby
mode and the POWER indicator...

E – 12
CANCEL
About Startup Screen
(Menu Language Select screen)
When you first turn on the projector, you will get the Star tup screen.
This screen gives you the opportunity to select one of the seven menu languages: English, German,
French, Italian, Spanish,Swedish and Japanese.
To select a menu language, follow these steps:
1. Use the Select 
 or  button to select one of the seven languages for the menu.
OFF
+-
PICTUREADJUSTABC DEFGHI
JKL MNO PQR
STU
,.
UNDO CANCEL
TEST
PICTUREKEYSTONE AMPLITUDE...

E – 13
Set up the projector
1. Turn on the projector
2. Select your type of projection:
Desktop front, ceiling rear, desktop rear, and ceiling front.
3. Display the test pattern by pressing the TEST button on the re-
mote control or using the menu.
TEST
4. Adjust the image position and the image size.
(1) Press and hold the CTL button and press the POSITION button to display
the Lens Shift adjustment screen.
Use the Select button on the remote control or the LENS SHIFT button on
the projector cabinet to...