NEC Projector PX602UL-WH User Manual

8
Terminals Features
9714238
13
1210
11 56
1.	 COMPUTER	1	IN/	Component	Input	T
erminal 	
(Mini	D-Sub	15	Pin)	
	(→	page	13,	125,	131,	166)
2.	 DisplayPort	IN	T erminal 	 (DisplayPort 	 20 	 Pin)
	(→	page	126,	166)
3.	 HDMI	IN	T erminal 	 (Type 	 A) 	
	(→	page	126,	128,	132,	166)
4.	 BNC	Input	[R/Cr/CV,	 G/Y/Y,	 B/Cb/C,	 H,	V] 	T ermi-
nals	(BNC	×	5)	
	(→	page	125,	130)
5.	 BNC	(Y/C)	Input	T erminal 	 (BNC 	 × 	 2) 	
	(→	page	130)
6.	 BNC	(CV)	Input	T erminal 	 (BNC 	 × 	 1) 	
	(→	page	130)
7.	 USB	Port...

9
❹ Part Names of the Remote Control
1. Infrared Transmitter
	(→	page	11)
2.	 Remote	Jack
	 Connect	a 	commercially 	a vailable 	
remote	cable	here 	f or 	wired 	oper a-
tion.	(→	page	11)
3.	 POWER	ON	Button
	(→	page	14)
4.	 POWER	OFF	Button
	(→	page	24)
5.	 INFO/L-CALIB.	 Button
	 Display	the	[SOURCE(1)] 	screen 	
of	the	on-screen	menu.
	(→	page	117)
6.	 VOL./FOCUS	+/−	Buttons
	(→	page	21)
7.	 D-ZOOM/ZOOM	+/−	Buttons
	(→	page	28)
8.	 TEST	Button
	(→	page	70)
9.	 ECO/L-SHIFT	Button
	(→	page	20,	29)
10....

10
Battery Installation
1. Press the catch and remove 
the battery cover.
2. Install new ones (AA). En-
sure that you have the bat -
teries’ polarity (+/−) aligned 
correctly.3. Slip the cover back over the batteries until 
it snaps into place.
NOTE:	Do 	not 	mix 	different 	types 	of 	batteries 	or 	new 	
and old batteries.
1
212
Remote Control Precautions
•	 Handle	the	remote	control	carefully.
•	 If	the	remote	control	gets	wet,	wipe	it	dry	immediately.
•	 Avoid	excessive	heat	and	humidity.
•	 Do	not...

11
Operating Range for Wireless Remote Control
7	m/276	inch
7	m/276	inchRemote 	 control
Remote
	
sensor
	
on
	
projector
	
cabinet
7	m/276	inch
7	m/276	inch 30°
30°
30° 30°
15°
30°
30° 30°
15°
30°
•	 The	infrared	signal 	oper ates 	b y 	line-of-sight 	up 	to 	a 	distance 	of 	abo ve 	meters 	and 	within 	a 	60-deg ree 	angle 	of 	the 	
remote	sensor	on	the	projector	cabinet.
•	 The	projector	will 	not 	respond 	if 	there 	are 	objects 	betw een 	the 	remote 	control 	and 	the 	sensor , 	or 	if 	strong...

12
This	section	describes	how	to	turn	on	the	projector	and	to	project	a	picture	onto	the	screen.
❶ Flow of Projecting an Image
Step 1
•	 Connecting	your	computer	/	Connecting	the	power	cord	(→ page 13)
 
Step 2 
•	 Turning	on	the	projector	(→ page 14)
 
Step 3 
•	 Selecting	a	source	(→ page 16)
 
Step 4
•	 Adjusting	the	picture	size	and	position	(→ page 18)
•	 Correcting	keystone	distortion	[CORNERSTONE]	(→ page 32)
 
Step 5
•	 Adjusting	a	picture
-	 Optimizing	a	computer	signal	automatically	(→	page...

13
❷ Connecting Your Computer/Connecting the Power Cord
1.	 Connect	your	computer	to	the	projector.
	 This	section	will 	sho w 	y ou 	a 	basic 	connection 	to 	a 	computer .	F or 	inf ormation 	about 	other 	connections , 	see 	“(2) 	
Making	Connections”	on 	 page 	125.
	 Connect	the	displa y 	output 	ter minal 	(mini 	D-sub 	15 	pin) 	on 	the 	computer 	to 	the 	COMPUTER 	1 	IN 	ter minal 	on 	the 	
projector	with	a 	commercially-a vailable 	computer 	cab le 	(with 	f errite 	core) 	and 	then 	tur n...

14
❸ Turning on the Projector
NOTE:
•	 The	projector	has	two	power	switches:	A	main	power	switch	and	a	POWER	button	(POWER	ON	and	OFF	on	the	remote	control)
•	Turning	 on 	 the 	 projector:
1. Press the main po wer switch to the ON position (I).
	 The	projector	will	go	into	standby	mode.
2. Press the POWER button .
	 The	projector	will	become	ready	to	use.
•	Turning	 off 	 the 	 projector:
1. Press the POWER button.
	 The	confirmation	message	will	be	displayed.
2. Press the POWER button again.
	 The...

15
Note on Startup screen (Menu Language Select screen)
When	you	first 	tur n 	on 	the 	projector , 	y ou 	will 	get 	the 	Star tup 	men u.	This 	men u 	giv es 	y ou 	the 	oppor tunity 	to 	select 	one 	
of	the	29	menu	languages.
To	select	a	menu	language,	follow 	 these 	 steps:
1. Use the ▲, ▼, ◀ or ▶	button 	to 	select 	one 	of 	the 	29 	
languages	from	the	menu.
 
2. Press the ENTER button to execute the selection.
After	this	has 	been 	done , 	y ou 	can 	proceed 	to 	the 	men u	
operation.
If	you...

16
❹ Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or video source equipment connected to the projector.
Detecting	the	Signal	Automatically
Press	the	SOURCE 	b utton 	f or 	1 	second 	or 	longer .	The 	projector 	will	
search	for	the 	a vailable 	input 	source 	and 	displa y 	it.	The 	input 	source 	will 	
change	as	follows:	
HDMI	→	DisplayPort	→	BNC	→	BNC(CV) 	→	BNC(Y/C) 	→	COMUPTER 	
→	HDBaseT	→	SLOT	→ …
•	 Press	it	briefly	to	display	the	[INPUT]	screen.	
	 Press...

17
Selecting Default Source 
You	can	set	a	source	as	the	default	source	so	that	it	will	be	displayed	each	time	the	projector	is	turned	on.
1. Press the MENU button.
	 The	menu	will	be	displayed.
2. Press the ▶	button	to	select	[SETUP]	and	press	the	▼	button	or	the	ENTER	button	to	select	[BASIC].
3. Press the ▶	button	to	select	[SOURCE	OPTIONS].
4. Press the ▼	button	four	times	to	select	[DEFAULT	INPUT	SELECT]	and	press	the	ENTER	button.
	 The	[DEFAULT	INPUT	SELECT]	screen	will	be	displayed.
	(→	page...