NEC Projector PH1400U User Manual

37
3. Convenient Features
❶ Blocking the lamp light (LENS 
SHUTTER)
Press	 the	SHUTTER/HOME	 POSITION	button	to	block	 the	lamps	 light	
from	hitting	 the	screen. 	Press	 again	to	allow	 the	screen	 to	become	 il-
luminated	again.
•	 Another 	way 	to 	shut 	the 	lamp 	light 	off 	is 	to 	press 	the 	SHUTTER 	button	
on	the	remote	control.
NOTE: 
•	 Do	 not	press	 and	hold	 the	SHUTTER/HOME	 POSITION	button	for	2	seconds	 or	
longer.
 Doing so will cause the lens shift position to return to the home...

38
3. Convenient Features
❺ Enlarging a Picture
You	can	enlarge	the	picture	up	to	four	times.
NOTE:	The	maximum	 magnification	 may	be	less	 than	 four	times	 depending	 on	
the signal.
To	do	so:
1.	 Press	the	D-ZOOM/ZOOM	(+)	button	to	magnify	the	picture.
2. Press the ▲▼◀▶ button.
	 The	area	of	the	magnified	image	will	be	moved
3.	 Press	the	D-ZOOM/ZOOM	(−)	button.
	 Each	 time	the	D-ZOOM/ZOOM	 (−)	button	 is	pressed,	 the	image	 is	
reduced.
NOTE: 
•	 The	image	will	be	enlarged	or	reduced	at	the	center...

39
3. Convenient Features
❻ Changing Eco Mode/Checking Energy-Saving Effect Using 
Eco Mode [ECO MODE]
This	feature	enables	you	to	select	two	brightness	modes	of	the	lamp:
OFF	and	ON	modes. 	The	lamp	life	can	be	extended	by	turning	on	the	[ECO	MODE].
[ECO	MODE]	Description
[OFF]
This	is	the	default	setting	(100%	Brightness).
[ON]Low	lamp	power	consumption	(approx. 	75%	Brightness).
To	turn	on	the	[ECO	MODE],	do	the	following: 	
1.	 Press	the	ECO/L-SHIFT	button	on	the	remote	control	to	display	[ECO	MODE]...

40
3. Convenient Features
Checking Energy-Saving Effect [CARBON METER]
This	feature	 will	show	 energy-saving	 effect	in	terms	 of	CO2	emission	 reduction	 (kg)	when	 the	projector’s	 [ECO	MODE]	
is	set	to	[ON]. 	This	feature	is	called	as	[CARBON	METER].
There	 are	two	 messages: 	[TOTAL	 CARBON	 SAVINGS]	 and	[CARBON	 SAVINGS-SESSION]. 	The	 [TOTAL	 CARBON	
SAVINGS]	 message	shows	the	total	 amount	 of	CO2	emission	 reduction	 from	the	time	 of	shipment	 up	to	now. 	You	 can	
check	the	information	on...

41
3. Convenient Features
❼ Correcting Horizontal and Vertical Keystone Distortion 
[CORNERSTONE]
Use	the	3D	Reform	 feature	to	correct	 keystone	 (trapezoidal)	 distortion	to	make	 the	top	or	bottom	 and	the	left	or	right	
side	of	the	screen	longer	or	shorter	so	that	the	projected	image	is	rectangular.
Cornerstone
1.	 Press	and	hold	the	3D	REFORM	button	for	a	minimum	of	2	seconds	to	reset	current	adjustments.
	 Current	adjustments	for	[KEYSTONE]	or	[CORNERSTONE]	will	be	cleared.
2.	 Project	an	image	so...

42
3. Convenient Features
7. Use the ▲▼◀▶	button	to	move	the	projected	image	frame	as	shown	on	the	example.
8.	 Press	the	ENTER	button.
9.  Use the ▲▼◀▶ button to select another icon which points in the direction.
	 On	the	Cornerstone	adjustment	screen,	select	[EXIT]	or	press	the	EXIT	button	on	the	remote	control.
	 The	confirmation	screen	is	displayed.
10. Press the ◀ or ▶	button	to	highlight	the	[OK]	and	press	the	ENTER	button.
This	completes	the	Cornerstone	correction.
Selecting	[CANCEL]	will	return...

43
3. Convenient Features
The	adjustable	ranges	for	3D	Reform	are	as	follows:
HORIZONTALVERTICAL
CORNERSTONE
Max. 	+/−	35°	approx.Max.	+/−	30°	approx.KEYSTONE
*	 The	following	are	conditions	under	which	the	maximum	angle	is	achieved:
•	 When	the	NP27ZL	lens	is	used
•	 When	the	lens	shift	is	set	to	the	center
	 When	 the	lens	 shift	is	used	 and	yet	the	 image	 is	not	 displayed	 in	the	 center	 of	the	 screen,	 the	adjustable	 range	
will	be	increased	or	decreased.
•	 Image	is	projected	in	maximum	wide...

44
3. Convenient Features
❽ Displaying Two Pictures at the Same Time
The	projector	 has	a	feature	 that	allows	 you	to	view	 two	different	 signals	simultaneously. 	You	 have	 two	modes: 	PIP	
mode	and	PICTURE	BY	PICTURE	mode.
•	 From	the	menu	you	can	select	[SETUP]	→	[BASIC]	→	[PIP/PICTURE	BY	PICTURE]. 	
The	[PIP/PICTURE	BY	PICTURE]	menu	item	has	the	following	three	options: 	MODE,	POSITION,	and	SOURCE.
Use	the	▲ or ▼	button	to	select	[MODE],	[POSITION]	or	[SOURCE]	and	press	the	ENTER	button.
Selecting...

45
3. Convenient Features
Viewing	Two	Pictures
1.	 Press	the	PIP/FREEZE	button	on	the	remote	control.
	 The	PIP/PICTURE	BY	PICTURE	SOURCE	screen	will	be	displayed.
 
2. Use the ▲ or ▼	button	to	select	the	source	and	press	the	ENTER	button.
	 The	 PIP	screen	 or	PICTURE	 BY	PICTURE	 screen	will	be	displayed,	 depending	 on	which	 was	selected	 in	the	
[MODE] setting screen.
 
3.	 Press	the	PIP/FREEZE	button	again	to	return	to	the	normal	screen	(single	picture).
TIP:
•	 Selecting	another	source	will	return...

46
3. Convenient Features
❾ Preventing the Unauthorized Use of the Projector [SECURITY]
A	keyword	 can	be	set	 for	your	 projector	 using	the	Menu	 to	avoid	 operation	 by	an	 unauthorized	 user.	When	 a	keyword	
is	 set,	 turning	 on	the	 projector	 will	display	 the	Keyword	 input	screen. 	Unless	 the	correct	 keyword	 is	entered,	 the	pro-
jector	cannot	project	an	image. 	
•	The	[SECURITY]	setting	cannot	be	cancelled	by	using	the	[RESET]	of	the	menu.
To	enable	the	Security	function:
1.	 Press	the	MENU...