NEC Projector Ph1000u User Manual

27
2. Projecting an Image (Basic Operation)
Zoom
Use	the	ZOOM	(+)	or	(−)	button	on	the	projector	cabinet	to	zoom	in	or	out.
Adjusting with buttons on the remote control
1.	 Press	the	FOCUS/ZOOM	 button	to	display	 the	adjustment	 win-
dow.
2.	 Press	the	▼	button	to	select	[ZOOM].
3.	 Use	the	◀ or ▶	button	to	zoom	in	or	out.
4.	 Press	 the	FOCUS/ZOOM	 button	again	to	close	 the	adjustment	
window. 

28
2. Projecting an Image (Basic Operation)
 Correcting Keystone Distortion
When	the	projector	 is	not	 exactly	 perpendicular	 to	the	 screen,	 keystone	 distortion	 occurs.	To	 overcome	 it,	you	 can	 use	
the	“Keystone” 	function,	 a	digital	 technology	 that	can	adjust	 for	keystone-type	 distortion,	resulting	in	a	crisp,	 square	
image.
The	following	 procedure	 explains	how	to	use	 the	[KEYSTONE]	 screen	from	the	menu	 to	correct	 trapezoidal	 distor-
tions.
When	the	projector	is	placed	diagonally...

29
2. Projecting an Image (Basic Operation)
NOTE:
•	 If	the	projection	angle	is	the	same	as	in	the	last	use,	the	previous	correction	setting	values	are	retained	in	the	memory.
•	 When	doing	Step	2,	adjust	the	position	of	image	so	that	the	screen	is	smaller	than	the	area	of	the	projected	area.
•	 To	reset	the	3D	Reform	correction	setting	values,	press	and	hold	the	3D	REFORM	button	for	a	minimum	of	2	seconds.
•	 Each	time	the	3D	REFORM	 button	is	pressed,	 the	item	 will	change	 as	follows:	 KEYSTONE	→...

30
2. Projecting an Image (Basic Operation)
 Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
Optimizing	a	computer	image	automatically.	(COMPUTER1/COMPUTER2/COMPUTER3)
Press	the	AUTO	ADJ.	button	to	optimize	a	computer	image	automatically.
This	adjustment	may	be	necessary	when	you	connect	your	computer	for	the	first	time.
[Poor picture]
[Normal picture]
NOTE:
Some	signals	may	take	time	to	display	or	may	not	be	displayed	correctly.
•	 If	the 	Auto 	Adjust 	operation 	cannot...

31
2. Projecting an Image (Basic Operation)
 Turning off the Projector
To turn off the projector:
1.	 First,	press	 the		(POWER)	 button	on	the	 projector	
cabinet	 or	the	 POWER	 OFF	button	 on	the	 remote	 con-
trol. 
	 The	 [POWER	 OFF	/	ARE	 YOU	 SURE	 ?	/	CARBON	 SAV-
INGS-	SESSION	0.000[g-CO2]]	message	will	appear.
2.	 Secondly, 	press 	the 	ENTER 	button 	or 	press 	the 	 
(POWER)	or	the	POWER	OFF	button	again.
	 The	 lamp	will	turn	 off	and	 the	projector	 will	go	into	 standby	
mode. 	When	 in...

32
2. Projecting an Image (Basic Operation)
 CAUTION:
Parts	of	the	 projector	 may	become	 temporarily	 heated	if	the	 projector	 is	turned	 off	with	 the	POWER	 button	or	if	the	
AC	power	supply	is	disconnected	during	normal	projector	operation.
Use	caution	when	picking	up	the	projector.
NOTE:
•	 While	the	POWER	indicator	is	blinking	blue	in	short	cycles,	the	power	cannot	be	turned	off.
•	 You	cannot	turn	off	the	power	for	60	seconds	immediately	after	turning	it	on	and	displaying	an	image.
•	 Wait	 at...

33
2. Projecting an Image (Basic Operation)
 Carrying the Projector
Preparation:	Make	sure	that	the	projector	is	turned	off.
1.	 Unplug	the	power	cord.
2.	 Disconnect	any	other	cables.
•	 Remove	the	USB	memory	if	it	is	inserted	into	the	projector.
•	 Remove	the	lens	before	shipping	the	projector.
3. Mount	the	lens	cap	on	the	lens.
4. Before	moving	the	projector, 	screw	in	the	tilt	feet	if	they	have	been	lengthened.
NOTE:
•	 Do	not	apply	strong	shock	or	force	to	the	projector	while	carrying	the...

34
3. Convenient Features
1 Blocking the lamp light (LENS 
SHUTTER)
Press	 the	SHUTTER/HOME	 POSITION	button	to	block	 the	lamps	 light	
from	hitting	 the	screen. 	Press	 again	to	allow	 the	screen	 to	become	 il-
luminated	again.
•	 Another 	way 	to 	shut 	the 	lamp 	light 	off 	is 	to 	press 	the 	SHUTTER 	button	
on	the	remote	control.
NOTE: 
•	 Do	 not	press	 and	hold	 the	SHUTTER/HOME	 POSITION	button	for	2	seconds	 or	
longer.
 Doing so will cause the lens shift position to return to the home...

35
3. Convenient Features
 Enlarging a Picture
You	can	enlarge	the	picture	up	to	four	times.
NOTE:	The	maximum	 magnification	 may	be	less	 than	 four	times	 depending	 on	
the signal.
To	do	so:
1.	 Press	the	D-ZOOM	(+)	button	to	magnify	the	picture.
2. Press	the		button.
	 The	area	of	the	magnified	image	will	be	moved
3.	 Press	the	D-ZOOM	(−)	button.
	 Each	time	the	D-ZOOM	(−)	button	is	pressed,	the	image	is	reduced.
NOTE: 
•	 The	image	will	be	enlarged	or	reduced	at	the	center	of	the	screen.
•...

36
3. Convenient Features
 Changing Eco Mode/Checking Energy-Saving Effect Using 
Eco Mode [ECO MODE]
This	feature	enables	you	to	select	two	brightness	modes	of	the	lamp:
OFF	and	ON	modes. 	The	lamp	life	can	be	extended	by	turning	on	the	[ECO	MODE].
[ECO	MODE]	Description
[OFF]
This	is	the	default	setting	(100%	Brightness).
[ON]Low	lamp	power	consumption	(approx. 	80%	Brightness).
To	turn	on	the	[ECO	MODE],	do	the	following: 	
1.	 Press	the	ECO	button	on	the	remote	control	to	display	[ECO	MODE]	screen....