NEC Projector Ph1000u User Manual

17
2. Projecting an Image (Basic Operation)
2.	 Press	the		(POWER)	 button	on	the	 projector	 cabinet	
or	the	POWER	ON	button	on	the	remote	control. 	
	 The	POWER	 indicator	 will	turn	 to	blue	 and	the	projector	
will	become	ready	to	use.
TIP:	
•	 When	 the	message	 “PROJECTOR	 IS	LOCKED!	 ENTER	YOUR	
PASSWORD.” 	is 	displayed, 	it 	means 	that 	the 	[SECURITY]	
feature	is	turned	on.	(→ page 45)
•	 When	 the	ECO	 message 	is	 displayed, 	it	 means 	that	 [ON]	 is	
selected	for	[ECO	MESSAGE].	(→ page...

18
2. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When	you	first	 turn	 on	the	 projector,	 you	will	get	 the	Startup	 menu.	This	 menu	 gives	you	the	opportunity	 to	select	 one	
of	the	27	menu	languages.
To	select	a	menu	language, 	follow	these	steps:
1.	 Use	the	, ,   or 	button	 to	select	 one	of	the	 27	lan-
guages	from	the	menu.
2.	 Press	the	ENTER	button	to	execute	the	selection.
After	 this	has	 been	 done,	 you	can	 proceed	 to	the	 menu...

19
2. Projecting an Image (Basic Operation)
If the projected image is inverted or upside down
1	 Press	the	ORIENTATION	button.	
	 The	[ORIENTATION]	screen	will	be	displayed.
2	 Press	again	to	select	a	correct	orientation.
	 Each	time	 the	ORIENTATION 	button 	is 	pressed,	 the	choice	 you	highlight 	
will	be	changed.
DESKTOP	FRONTDESKTOP	REAR
CEILING	FRONTCEILING	REAR
3	 Stop	pressing	the	ORIENTATION	button.
	 The	menu	will	be	closed	 and	the	projected	 image	will	be	displayed	 in	
the	correct...

20
2. Projecting an Image (Basic Operation)
 Selecting a Source
Selecting the computer or video source
NOTE:	Turn	on	the	computer	or	video	source	equipment	connected	to	the	projector.
Detecting	the	Signal	Automatically
Press	the 	SOURCE 	button 	once. 	The 	projector 	will 	search 	for 	the 	available	
input	source	and	display	it. 	The	input	source	will	change	as	follows: 	
COMPUTER1	→	COMPUTER2	→	COMPUTER3	→	HDMI	→	DisplayPort 	
→	VIDEO	→	S-VIDEO	→	VIEWER	→	SLOT	→	COMPUTER1	→ ...
•	 With	 the	SOURCE...

21
2. Projecting an Image (Basic Operation)
 Adjusting the Picture Size and Position
Use	the	horizontal	 adjustment	 knob	and	adjustable	 tilt	feet	 to	finely	 tilt	the	 projector; 	use	 the	LENS	 SHIFT,	 ZOOM,	
and	FOCUS	buttons	to	adjust	the	picture	size	and	position.
In	this	chapter	drawings	and	cables	are	omitted	for	clarity.
Tilting	the	projector
[Horizontal	adjustment	knob/Tilt	feet]
Adjusting	 the	projected	 image’s	vertical	and	horizontal	
position
[Lens	shift]
(→ page 22) (→ page 24)
Adjusting...

22
2. Projecting an Image (Basic Operation)
CAUTION•	 Perform	the	adjustment	 from	behind	 or	from	 the	side	 of	the	 projector. 	Adjusting	 from	
the	front	 could	 expose	 your	eyes	 to	strong	 light	which	 could	injure	 them.	The	 rear	
vents	 of	the	 projector	 may	become	 heated	during	normal	 projector	 operation. 	Use	
caution	when	adjusting	the	tilt	foot	on	the	rear	side. 	
•	 Keep	hands	away	from	the	lens	 mounting	 portion	while	the	lens	 shift	is	in	 operation. 	
Failure	to	do	so	could	result...

23
2. Projecting an Image (Basic Operation)
4.	 Rotate	each	of	the	 tilt	feet	 to	adjust	 the	height	 while	keeping	 the	projector	 level	with	the	floor/ceiling	 and	
perpendicular	to	the	screen	when	viewed	from	the	side.
	 To	raise	the	front	side	of	the	projector,	extend	the	left	and	right	tilt	feet.
	 To	lower	the	front	side	of	the	projector,	extend	the	rear	foot.
	 Adjustable	range: 	2°
Screen90°
Lower
Raise
Front tilt foot
 
NOTE:
•	 Do	 not	lengthen	 each	of	the	 tilt	feet	 any	more	 than	13...

24
2. Projecting an Image (Basic Operation)
Adjusting the vertical position of a projected image (Lens shift)
NOTE:
•	 The	lens	shift	function	is	not	available	on	the	projector	with	NP25FL	(fixed	focus)	lens	installed.	
	 Return	the	lens	shift	position	to	the	home	position	before	installing	the	lens	to	the	projector.
•	 Shifting	the	lens	 to	the	 maximum	 in	two	 directions	 combined	 will	cause	 the	edges	 of	the	 image	 to	become	 dark	or	will	 cause	
some shadows.
Adjusting with buttons on the...

25
2. Projecting an Image (Basic Operation)
Adjusting with the remote control
1.	 Press	the	LENS	SHIFT	button.
	 The	Lens	Shift	screen	will	be	displayed.	
2.	 Press	the	▼▲◀ or ▶	button.
 Use the ▼▲◀▶	buttons	to	move	the	projected	image.
TIP:	
•	 The	 diagram	 below	shows	 the	lens	 shift	 adjustment	 range	for	the	 desktop	 front.	To	raise	 the	projection	 position	higher	than	this,	
use	the	tilt	feet.	(→ page 22)
1V
1H
0.2H 0.2H
0.55V
0.4VHeight of projected image
Width	of	projected	image 

26
2. Projecting an Image (Basic Operation)
Focus
Applicable	lens:	NP26ZL/NP27ZL/NP28ZL/NP29ZL
Use	the	FOCUS	(+)	or	(−)	button	on	the	projector	cabinet	to	obtain	the	best	focus.
TIP:	To	obtain	the	best	focus,	perform	the	following	(for	fixed	installation)
Preparation:	Warm	up	the	projector	for	one	hour.
1.	Use	the	FOCUS	+/−	buttons	to	make	sure	you	obtain	the	best	focus.	If	you	do	not,	move	the	projector	back	and	forth.
2.	Select	the	[TEST	PATTERN]	from	the	menu	and	display	the	test	pattern.	(→ page...