NEC Projector PA621U User Manual

							129
5. Using On-Screen Menu
17. On  the  thumbnail  screen,  select  a  digital  certificate  (DER  format  file)  saved  in  your  USB  memory  device 
and press the ENTER button.
•	 Select	your	root	CA	certificate	here. 	
 The selected digital certificate will be installed on the projector.
18.	After	completing	required	settings, 	select	[OK]	and	press	the	ENTER	button.
 The [WIRELESS] page will be returned.
19.	Select	[RECONNECT]	and	press	the	ENTER	button.
20.	Select	[OK]	and	press	the	ENTER	button.
This	will	complete	setting	[EAP-TLS]	for	[EAP	 TYPE]	in	[WPA-EAP]	or	[WPA2-EAP].
TIP:
Clearing	the	digital	certificate	that	is	installed	on	the	projector
To	clear	the	digital	certificate	installed	on	the	projector,	follow	the	steps	below.
By	doing	the	following	procedure,	all	the	digital	certificates	for	the	currently	displayed	profile	will	be	cleared.
1.	 Select	[CLEAR 	CERTIFICATES] 	in 	the 	bottom 	left 	of 	the 	[AD-
VANCED]	setting	screen	and	press	the	ENTER	button.
  A message for confirmation will be displayed.
2.	 Select	[YES]	and	press	the	ENTER	button.
 The digital certificates will be cleared.
TIP:
•	 The	PKCS#12	format	digital	certificate	including	a	CA	certificate	will	be 	installed	as	a	root	CA	certificate.
② Selecting [PEAP-MSCHAPv2] for [EAP TYPE]:
12.	From	the	[AUTHENTICATION]	page,	select	[EAP	TYPE]	field	and	press	the	ENTER	button.
 The pull-down list will be displayed.
13.	Select	[PEAP-MSCHAPv2]	and	press	the	ENTER	button.
14.	Select	[USER	NAME]	field	and	press	the	ENTER	button.
 The character entry screen (software keyboard) will be displayed. Set a user name.
•	 A	user	name	must	be	32	characters	or	less.
 (→ page 131) 
						

							130
5. Using On-Screen Menu
15.	After	completing	setting	a	user	name,	select	the	[PASSWORD]	field	and	press	the	ENTER	button.
 The character entry screen (software keyboard) will be displayed. Set a password.
•	 A	password	must	be	32	characters	or	less.
16.	After	completing	setting	the	password, 	select	[CA	CERTIFICATE]	field	and	press	the	ENTER	button.
 The drive list screen will be displayed.
•	 For	operating	the	thumbnail	screen,	see	 “4.	Using	the	 Viewer”	in	the	“User’s	Manual” 	(PDF).
•	 To	return	to	the	[AUTHENTICATION]	page,	press	the	EXIT	button.
NOTE:
Installing a digital certificate
You	can	install	 each	digital	 certificate	 (client	certificate	 and	CA	certificate)	 for	[PROFILE	 1	(or	 2)]	on	a	file-by-file	
basis.
•	 Install	a	root	CA	certificate	for	a	CA	certificate.
•	 If	 you	install	 a	digital	 certificate	 over	your	 existing	 digital	certificate,	 the	existing	 digital	certificate	 will	be	overwritten	 with	the	new	
digital	certificate.
•	 Once	a	digital	certificate	has	been	installed,	its	information	cannot	be	deleted	even	if	you	stop	setting	WPA-EAP	or	WPA2-EAP.
17. On  the  thumbnail  screen,  select  a  digital  certificate  (DER  format  file)  saved  in  your  USB  memory  device 
and press the ENTER button.
•	 Select	your	root	CA	certificate	here. 	
 The selected digital certificate will be installed on the projector. 
						

							131
5. Using On-Screen Menu
18.	After	completing	required	settings,	select	[OK]	and	press	the	ENTER	button.
 The [WIRELESS] page will be returned.
19.	Select	[RECONNECT]	and	press	the	ENTER	button.
20.	Select	[OK]	and	press	the	ENTER	button.
This	will	complete	setting	[PEAP-MSCHAPv2]	for	[EAP	 TYPE]	in	[WPA-EAP]	or	[WPA2-EAP].
TIP:
Clearing	the	digital	certificate	that	is	installed	on	the	projector
To	clear	the	digital	certificate	installed	on	the	projector,	follow	the	steps	below.
By	doing	the	following	procedure,	all	the	digital	certificates	for	the	currently	displayed	profile	will	be	cleared.
1.	 Select	[CLEAR 	CERTIFICATES] 	in 	the 	bottom 	left 	of 	the 	[AD-
VANCED]	setting	screen	and	press	the	ENTER	button.
  A message for confirmation will be displayed.
2.	 Select	[YES]	and	press	the	ENTER	button.
 The digital certificates will be cleared.
TIP:
Entering	 WEP	keys	(Switching	between	Alphanumeric	characters	and	hexadecimal)
To	enter	from	[KEY1]	to	[KEY4],	do	the	following:
1.	 Select	one	of	[KEY	1], 	[KEY	2],	[KEY	3]	and	[KEY	4]	and	press	the	ENTER	button. 	
 The character entry screen (software keyboard) will be displayed.
2. Use the ▼, ▲, ◀, or ▶ button to select a character and press the ENTER button.
•	 To	 enter	a	WEP	 key	or	passphrase,	 use	alphanumeric	 characters	(ASCII)	or	hexadecimal	 (HEX).	To	 enter	 a	PSK	
key, use alphanumeric characters (ASCII).
•	 Press	 the	[HEX]	 button	 to	change	 to	[ASCII]	 to	set	 the	 key	 in	ASCII	 digit.	You	 can	toggle	 this	button	 between	
[ASCII] and [HEX].
•	 Enter	0x(numeral	and	alphabet	respectively)	right	in	front	of	your	key	code.
•	 Hexadecimal	uses	0	to	9	and	A	to	F.
3. After entering your WEP key or passphrase, use the ▼, ▲, ◀, or ▶	button 	to 	select 	[OK] 	and 	press 	the 	ENTER	
button.
  The character entry screen (software keyboard) will be closed. 
						

							132
5. Using On-Screen Menu
WPS
When	the	wireless	 LAN	access	 point	connected	 to	the	 projector	 supports	WPS	(Wi-Fi	 Protected	 Setup	TM),	you	can	
use	PIN	method	or	push	button	method	to	set	up	the	wireless	LAN	for	the	projector.
PIN	 TYPESet	a	4-digit	 or	8	digit-PIN	 code	of	WPS	 for	your	 access	 point	to	complete	 setting	for	the	
SSID	security.
PUSH	BUTTON	 TYPEPress	the	dedicated	 button	of	the	 access	 point	and	the	projector’s	 wireless	LAN	unit	to	
complete	setting	for	the	SSID	security.
NETWORK	INFORMATION
The	 following	 information	 will	be	displayed	 when	the	projector	 is	connected	 to	a	network	 (wired	LAN	or	wireless	
LAN).
PROJECTOR	NAME
HOST	NAME
DOMAIN
NETWORK	INFOR-
MATION	(WIRED	
LAN/WIRELESS	LAN)
CONNECTION	STATUS,	IP	ADDRESS,	SUBNET	MASK,	GATEWAY,	 WINS,	DNS,	MAC	
ADDRESS,	SSID,	NETWORK	TYPE,	WEP/WPA,	CHANNEL,	SIGNAL	LEVEL,	AU-
THENTICATION,	AUTHENTICATION	PERIOD
DISPLAY	 THE	INFOR-
MATION	IN	APPLICA-
TION	MENU
Turn	on	or	off	the	display	of	the	network	information.
	The	meanings	of	these	status	statements	are	described	below.
StatementAuthentication	status
AuthenticatedAuthentication	is	done	correctly.
FailureAuthentication	failed.
Authenticating…Authentication	is	in	process.
ExpiredThe	digital	certificate	is	expired. 	Or	[DATE,	TIME	PRESET]	is	not	set	correctly.
Time	ErrorThe	[DATE,	 TIME	PRESET]	has	been	cleared. 	Set	the	correct	date	and	time. 
						

							133
5. Using On-Screen Menu
PROJECTOR	NAME	(ADVANCED	menu	only)
PROJECTOR	NAMESet	a	unique	projector	name.	Up	to	16	alphanu-
meric	characters	and	
symbols
DOMAIN	(ADVANCED	menu	only)
Set	a	host	name	and	domain	name	of	the	projector.
HOST	NAMESet	a	host	name	of	the	projector.Up	to	15	alphanumeric	
characters
DOMAIN	NAMESet	a	domain	name	of	the	projector.Up	to	60	alphanumeric	
characters 
						

							134
5. Using On-Screen Menu
ALERT	MAIL	(ADVANCED	menu	only)
ALERT	MAILThis	option	 will	notify	 your	computer	 of	lamp	 replace	 time	or	error	
messages	via	e-mail	when	using	wireless	or	wired	LAN. 	
Placing a checkmark will turn on the Alert Mail feature�
Clearing a checkmark will turn off the Alert Mail feature�
Sample	of	a	message	to	be	sent	from	the	projector:
The	lamp	 and	filters	 are	at	the	 end	 of	its	 usable	 life.	Please	
replace	the	lamp	and	filters.
Projector	Name: 	NEC	Projector
Lamp	Hours	Used: 	100	[H]	
—
HOST	NAMEType	in	a	host	name.Up	to	15	alphanumeric	
characters
DOMAIN	NAMEType	in	a	domain	 name	of	the	 network	 connected	 to	the	 projec-
tor.
Up	to	60	alphanumeric	
characters
SENDER'S	AD-
DRESS
Specify	the	sender’s	address. 	Up	to	60	alphanu-
meric	characters	and	
symbols
SMTP	SERVER	
NAME
Type	in	the	 SMTP	 server	 name	to	be	 connected	 to	the	 projec-
tor.	
Up	to	60	alphanumeric	
characters
RECIPIENT'S	AD-
DRESS	1,	2,	3
Type	in	your	recipient’s	address. 	Up	to	60	alphanu-
meric	characters	and	
symbols
TEST	MAILSend	a	test	mail	to	check	if	your	settings	are	correct.
NOTE:
•	 If	you	entered	 an	incorrect	 address	in	a	test,	 you	may	 not	receive	 an	
Alert	mail. 	Should 	this 	happen, 	check 	if 	the 	Recipient’s 	Address 	is	
correctly	set.
•	 Unless 	any 	one 	of 	the 	[SENDER'S 	ADDRESS], 	[SMTP 	SERVER'S	
NAME]	 or	[RECIPIENT'S	 ADDRESS	1-3]	is	selected,	 [TEST	MAIL]	 is	
not	available.
•	 Be	sure 	to 	highlight 	[OK] 	and 	press 	the 	ENTER 	button 	before 	executing	
[TEST	MAIL]. 	
— 
						

							135
5. Using On-Screen Menu
NETWORK	SERVICE	(ADVANCED	menu	only)
HTTP	SERVERSet	a	password	for	your	HTTP	server.Up	to	10	alphanumeric	
characters
PJLinkThis	option 	allows 	you 	to 	set 	a 	password 	when 	you 	use 	the	
PJLink	feature.
NOTE:	
•	 Do	 not	forget	 your	password.	 However,	if	you	 forget	 your	password,	
consult	with	your	dealer.	
•	 What	is	PJLink?
	 PJLink	 is	a	standardization	 of	protocol	 used	for	controlling	 projectors	
of	different	 manufacturers.	 This	standard	 protocol	is	established	 by	
Japan	Business	 Machine	and	Information	 System	Industries	 Associa-
tion	(JBMIA)	in	2005.
	 The	projector	supports	all	the	commands	of	PJLink	Class	1.
•	 Setting	of	PJLink	 will	not	be	affected	 even	when	 [RESET]	 is	done	 from	
the	menu. 	
Up	to	32	alphanumeric	
characters
AMXTurn	
on	or	off	 for	 detection	 from	AMX	 Device	 Discovery	 when	
connecting	 to	the	 network	 supported	 by	AMX’s	 NetLinx	 control	
system.
TIP:	
When	using	a	device	 that	supports	 AMX	Device	 Discovery,	 all	AMX	 NetLinx 	
control	 system	 will	recognize	 the	device	 and	download	 the	appropriate	
Device	Discovery	Module	from	an	AMX	server.
Placing a checkmark will enable detecting the projector from AMX Device 
Discovery �
Clearing  a  checkmark  will  disable  detecting  the  projector  from  AMX 
Device Discovery � 
— 
						

							136
5. Using On-Screen Menu
TOOLS
ADMINISTRATOR MODE
This	allows	you	to	select	MENU	MODE,	save	settings,	and	set	a	password	for	the	administrator	mode.
MENU	MODESelect	either	[BASIC]	or	[ADVANCED]	menu.
(→	page	84)
—
NOT	SAVE	SETTING	
VALUES
Placing a check mark will not save your projector settings�
Clear this check box to save your projector settings�
—
NEW	PASSWORD/
CONFIRM	PASS-
WORD
Assign	a	password	for	the	administrator	mode.Up	to	10	alphanumeric	
characters
NOTE:
When	[LAST]	 is	selected	 for	[DEFAULT	 SOURCE	SELECT],	 placing	a	check	 mark	for	[NOT	 SAVE	 SETTING	 VALUES]	 will	forcibly	
select	NETWORK	for	source	at	every	power-on	time.
To	avoid	this,	select	[AUTO]	for	[DEFAULT	SOURCE	SELECT].
TIP:
To	return	to	the	ADVANCED	menu	from	the	BASIC	menu,	do	the	following:
1.	 Use	 the	SOURCE	 button	on	the	 cabinet	 or	press	 the	NETWORK	 button	on	the	 remote	 control	 to	select	
[NETWORK]	to	display	the	APPLICATION	MENU.
2.	 Select	[TOOLS]	→	[ADMINISTRATOR	MODE]	→	[MENU	MODE]	→	[ADVANCED	MODE]. 	 
						

							137
5. Using On-Screen Menu
PROGRAM TIMER
This	option	 turns	on/off	 the	projector	 and	changes	 video	signals,	 and	selects	 ECO	mode	 automatically	 at	a	specified	
time.
NOTE:
•	 Before	using	[PROGRAM	TIMER],	make	sure	that	the	[DATE	AND	TIME]	feature	is	set.	(→	page	140)
•	 Make	sure	that	the	projector	is	in	the	stand	by	condition	with	the	POWER	cord	connected.
•	 The	 projector	 has	a	built-in	 clock.	The	clock	 will	keep	 working	 for	about	 two	weeks	 after	the	main	 power	 is	turned	 off.	If	the	 main	
power	is	not	supplied	to	the	projector	for	two	weeks	or	more,	the	built-in	clock	stops	working.
•	 When	[PROGRAM	TIMER]	is	enabled,	the	[STANDBY	MODE]	setting	becomes	invalid.
	 This	means	that	the	projector	is	in	the	same	condition	when	the	[NORMAL]	is	selected	for	[STANDBY	MODE].
Setting a new program timer
1. On the PROGRAM TIMER screen, use the ▲ or ▼	button	 to	select	 [SETTINGS]	 and	press	 the	ENTER	 but-
ton.
 The [PROGRAM LIST] screen will be displayed.
2. Select a blank program number and press the ENTER button.
  The [EDIT] screen will be displayed.
3. Make settings for each item as required.
ACTIVE ������������������Place a check mark to enable the program� 
						

							138
5. Using On-Screen Menu
DAY ������������������������Select days of the week for the program timer � To execute the program from Monday to Friday, select [MON-
FRI]�To execute the program in everyday basis, select [EVERYDAY]�
TIME ����������������������Set the time to execute the program� Enter time in 24-hour format�
FUNCTION  �������������Select a function to be executed� Selecting [POWER] will allow you to turn on or off the projector by setting 
[ADVANCED SETTINGS]� Selecting [SOURCE] will allow you to select a video source by setting [ADVANCED 
SETTINGS]�  Selecting  [ECO  MODE]  will  allow  you  to  select  [ECO  MODE]  by  setting  [ADVANCED  SET-
TINGS]�
ADVANCED SETTINGS
 ������������������������������Select power on/off, a type of video source, or ECO MODE for the selected item in [FUNCTION]�
REPEAT ������������������Place a check mark to repeat the program continuing basis� To use the program this week only, clear the 
check mark�
4.	 Select	[OK]	and	press	the	ENTER	button.
  This will complete the settings.
 You will be returned to the [PROGRAM LIST] screen.
5.	 Select	[BACK]	and	press	the	ENTER	button.
 You will be returned to the [PROGRAM TIMER] screen.
6.	 Select	[OK]	and	press	the	ENTER	button.
 You will be returned to the [TOOLS] screen.
NOTE:
•	 Up	to	30	different	timer	settings	can	be	programmed.
•	 When	[PROGRAM	TIMER]	is	turned	on,	the	[STANDBY	MODE]	setting	is	ignored.
•	 The	Program	Timer	is	executed	on	a	set	time	basis,	not	in	a	program	basis.
•	 Once	 the	program	 not	marked	 with	a	check	 in	[REPEAT]	 has	been	 executed,	 the	check	 mark	in	the	 [ACTIVE]	 check	box	will	be	
cleared	automatically	and	the	program	will	be	disabled.
•	 When	the	on-time	and	the	off-time	set	for	the	same	time,	the	off-time	setting	will	take	preference.
•	 Two	different	sources	are	set	for	the	same	time,	the	larger	program	number	will	take	preference.	
•	 The	on-time	setting	will	not	be	executed	while	the	cooling	fans	are	running	or 	an	error	is	occurring.
•	 If	the 	off-time 	setting 	is 	expired 	under 	the 	condition 	in 	which 	the 	power 	off 	is 	not 	possible, 	the 	off-timer 	setting 	will 	not 	be 	executed	
until	the	power	off	becomes	possible.
•	 Programs	 not	marked	 with	a	check	 mark	in	[ACTIVE]	 of	the	 [EDIT]	 screen	 will	not	be	executed	 even	if	the	 Program	 Timer	is	
enabled.
•	 When	 the	projector	 is	turned	 on	by	using	 the	program	 timer	and	if	you	 want	 to	turn	 off	the	 projector,	 set	the	 off-time	 or	do	 it	
manually	so	as	not	to	leave	the	projector	on	for	a	long	period	of	time.