NEC Projector P502HL User Manual

68
[P502WL]
012345678910 11 12131415
12 13 14 15
0
1 2
3
4
5
123456789 10 11
40
30 60 80
100
120 150
180
200 240
300
(inch)
(m)
Screen size
Screen height from the center of the 
projector lens
[Projection distance] When zoom lever turned to wide
With tilt feet tilted 4° when set to wide
When zoom lever turned to telescopic When zoom lever 
turned to telescopic
Screen center line 
(telescopic)
When zoom lever 
turned to wide
Projector lens center Screen center line (wide) (m) (m)
*	 The	figures	indicated...

69
Tables of screen sizes and dimensions
[P502HL]
Screen heightScreen widthScreen size  (diagonal)
Size	(inches)Screen	widthScreen	height(cm) (cm)
30 66.4 37.4
40 88.6 49.8
50 110.7 62.3
60 132.8 74.7
80 177.1 99.6
100 221.4 124.5
120 265.7 149.4
150 332.1 186.8
200 442.8 249.1
250 553.4 311.3
300 664.1 373.6
[P502WL]
Screen height
Screen widthScreen size  (diagonal)
Size	(inches)Screen	widthScreen	height(cm) (cm)
30 64.6 40.4
40 86.2 53.8
50 107.7 67.3
60 129.2 80.8
80 172.3 107.7
100 215.4 134.6
120...

70
Example of installation on a desktop
The	diagram	below	shows	an	example	of	when	the	projector	is	used	on	a	desktop.
Horizontal	projection	position:	Equal	distance	to	the	left	and	right	from	the	center	of	the	lens
Vertical	projection	position:	(see	table	belo w)	
[P502HL]
Screen surface
Lower edge of screen with 61.6% V Measurement +H
Measurement -H
Lower edge of screen with 0% V
Lens center
Approximately 92 to 97 mm Projection distance L
(Note)	Height	from	lens	center	to	lower	edge	of	screen	(with...

71
Lens shifting range
This	projector	is	equipped	with	a	lens	shift	function	(→	page	17)	for	adjusting	the	image	position	using	dials.	Lens	
shifting	is	possible	within	the	range	shown	below.
NOTE:	
•	 In	case	lens	shifted	volume	exceeds	the	below	illustrated	range,	blur	and	shade	may	appear	around	ends	of	projected	image.
Legend:	V	“Vertical”	refers	to	the	screen	height	and	H	“Horiz ontal”	refers	to	the	screen	width.	The	lens	shift	range	is	
expressed	as	a	ratio	of	height	and	width,	respectively....

72
(Example)	When	using	to	project	on	a	150"	screen
[P502HL]
According	to	the	“Table	of	screen	siz es	and	dimensions”	(→	page	70),	H	=	130.8"/332.1	cm,	V	=	73.6"/186.8	cm.
Adjustment	range	in	the	vertical	direction:	the	projected	image	can	be	mov ed	upwards	0.62	×	73.6"/186.8	cm	≈ 
45.3"/115	cm	(when	the	lens	is	at	the	center	position).	
Adjustment	range	in	the	horizontal	direction:	the	projected	image	can	be	mov ed	to	the	left	0.25	×	130.8"/332.1	cm	≈ 
32.7"/83	cm,	to	the...

73
❷ Making Connections
Connecting Your Computer
Computer	cables	and	HDMI	can	be	used	to	connect	to	a	computer.	The	HDMI	cable	is	not	enclosed	with	the	projector.	
Please	get	ready	a	suitable	cable	for	the	connection.
NOTE:	Signals	supported	by	Plug	&	Play	(DDC2)
INPUTCOMPUTER	INHDMI	1	INHDMI	2	INanalogdigitaldigital
Ye s Ye sYe s
HDMI 1 INHDMI 2 IN
COMPUTER IN
AUDIO IN
Computer cable (VGA) (supplied)
To mini D-Sub 15-pin terminal on the projector. 
It
	is	recommended	that	y
 ou
	use	a	commercial
 -
ly...

74
NOTE:	The	projector	is	not	compatible	with	video	decoded	outputs	of	the	NEC	ISS-6020	switcher.
NOTE:	An	image	may	not	be	displayed	correctly	when	a	Video	source	is	played	back	via	a	commercially	available	scan	converter.	
This	is	because	the	projector	will	process	a	video	signal	as	a	computer	signal	at	the	default	setting.	In	that	case,	do	the	following.
*	 When	an	image	is	displayed	with	the	lower	and	upper	black	portion	of	the	screen	or	a	dark	image	is	not	displayed	correctly:
	 Project	an	image	to...

75
Connecting an External Monitor
You	can	connect	a	separate,	exter nal	monitor	to	your	projector	to	simultaneously	view	on	a	monitor	the	computer	
analog	image	you’re	projecting.
AUDIO OUT
MONITOR OUT (COMP.)
Computer cable (VGA) (supplied)
Stereo mini-plug audio cable (not supplied)
Stereo mini-plug audio cable 
(not supplied)
Computer cable (VGA) (not supplied)
NOTE:
•	 The	AUDIO	OUT	mini	jack	does	not	support	Headphone	terminal.
•	 When	audio	equipment	is	connected,	the	projector	speaker	is...

76
Connecting Your DVD Player or Other AV Equipment
Connecting	Video	Input
VIDEO INAUDIO IN
Audio cable (not supplied)
Video cable (not supplied)
Audio cable (not supplied)
Audio equipment
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
VIDEO	IN	VIDEO(VIDEO)
NOTE:	Refer	to	your	VCR	owner’s	manual	for	more	information	about	your	equipment’s	video	output	requirements.
NOTE:	An...

77
Connecting Component Input
Connection	for	component	signal.	Signal	from	the	color	difference	signal	output	terminal	on	DVD	players	(DVD	video	
output)	and	the	YPbPr	output	terminal	on	the	Hi-vision	video	can	be	projected.	Recommend	to	connect	the	terminal	
for	audio	output	on	the	DVD	player	to	the	audio	components.
COMPUTER IN
AUDIO IN
15-pin - to - RCA (female) × 3 cable adapter 
(ADP-CV1E)
Stereo mini plug - to - RCA audio cable (not supplied)
Component video RCA × 3 cable (not supplied)
Audio cable...