NEC Np600s Projector User Manual


3. Projecting an Image (Basic Operation)
STATUS LAMP AUTOADJ. SOURCE 
SELECT MENU EXIT ENTER 
FOCUS FOCUS
Zoom
[NP600/NP500/NP400/NP00/NP500W]
Use the ZOOM lever to adjust the image size on the screen.
Zoom Lever
[NP600S/NP500WS]
The image size can be adjusted electronically from the menu. To do so, follow the steps below.
1. Press the MENU button.
  The menu will be displayed.
2.  Press the SELECT 
 button to select [SETUP] and press the ENTER button.
  The [GENERAL] tab will be...


3. Projecting an Image (Basic Operation)
STATUS LAMP AUTOADJ. SOURCE 
SELECT MENU EXIT ENTER 
FOCUS 
FOCUS
4. Use the SELECT  or  button to adjust the image size.
5.  After completing adjustment, press the EXIT button three times.
  The menu will be closed.
Focus
[NP600/NP500/NP400/NP00/NP500W]
Use the FOCUS ring to obtain the best focus.
Focus Ring
[NP600S/NP500WS]
Use the FOCUS lever to obtain the best focus.
STATUSLAMPAUTOADJ.SOURCESELECTMENUEXITENTER
FOCUSFOCUS
Focus Lever 

4
3. Projecting an Image (Basic Operation)
 Correcting Keystone Distortion
Correcting Keystone Distortion
If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following
steps to correct keystone distortion
 
NOTE: 
• The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
•  The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.
Adjusting with buttons on the...

5
3. Projecting an Image (Basic Operation)
Adjusting with the Remote Control
1. Press the MENU button.
The menu will be displayed.
2.  Press the SELECT 
 button to select [SETUP] and press the ENTER button.
 
The [GENERAL] screen will be displayed.
3.  Press the SELECT 
 button to select [KEYSTONE].
 
4.  Press the SELECT  or  button.
Adjust so that the image is rectangular.
5.  Press the MENU button.
The menu will be closed.
NOTE: The Keystone correction can cause an image to be slightly...

6
3. Projecting an Image (Basic Operation)
Adjusting with the Auto Keystone Function
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special 
operation required. Just put the projector on a flat surface.
TIP: Even when the menu setting for [AUTO KEYSTONE] is turned on, [KEYST\
ONE] can be adjusted manually.
To turn on [AUTO KEYSTONE], proceed the following steps.
1. Press the MENU button
The menu will be displayed.
2.  Press the...

7
3. Projecting an Image (Basic Operation)
 Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
Optimizing a computer image automatically.
Press the AUTO ADJ. button to optimize a computer image automatically.
This adjustment may be necessary when you connect your computer for the first time.
[Poor picture]
[Normal picture]
VOLUME
L-CLICKMOUSER-CLICK
ASPECTHELPFREEZEPICTURE
AUTO ADJ.S-VIDEOVIDEOCOMPUTER
LAMP MODE1
2
Increase volume
Decrease volume
VOLUME...

8
3. Projecting an Image (Basic Operation)
7 Turning off the Projector
To turn off the projector:
SELECT
MENU
EXITENTER
STATUSLAMP
AUTO ADJ.SOURCEENTEREXIT
MENU
UPMAGNIFYPAGE
OFFPOWERON
PIC-MUTE
DOWN
1. First,  press  the   (POWER)  button  on  the  projector 
cabinet or the POWER OFF button on the remote con-
trol. The [POWER OFF / ARE YOU SURE?] message will 
appear.
2.  Secondly,  press  the  ENTER  button  or  press  the  
(POWER) or the POWER OFF button again.
  The power indicator will glow...

9
3. Projecting an Image (Basic Operation)
 After Use
Preparaton: Make sure that the projector s turned off.
1. Unplug the power cable.
2.  Disconnect any other cables.
3.  Retract adjustable tilt foot if extended.
4.  Cover the lens with the lens cap.
5.  Put the projector and accessories in the supplied soft case.
  Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from 
damage.
NOTE: The NP600S and the NP500WS do not come with...

40
1 Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short 
period of time. Press again to restore the image and sound.
NOTE:
• 
Even though the image is turned off, the menu still remains on the scree\
n.
•  Sound from the AUDIO OUT jack (Stereo mini) can be turned off.
 Freezing a Picture
Press  the  FREEZE  button  to  freeze  a  picture.  Press  again  to  resume 
motion.
NOTE: The image is frozen but the original video is still playing back.
...

4
4. Convenient Features
 Changing Lamp Mode
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
To change to the [ECO] mode, do the following: 
1. Press the LAMP MODE button on the remote control to display [LAMP MODE] screen.
2.  Use the SELECT 
 or  button to select [ECO] mode.
3.  Press the ENTER button. 
To change from [ECO] to [NORMAL], Go back to Step 2 and select [NORMAL]. Repeat Step 3.
NOTE: 
•...