NEC Np600s Projector User Manual


2. Installation and Connections
[NP500W]
The  further  your  projector  is  from  the  screen  or  wall,  the  larger  the  image. The  minimum  size  the  image  can  be  is 
approximately  21"  (0.53  m)  measured  diagonally  when  the  projector  is  roughly  28  inches  (0.7  m)  from  the  wall  or 
screen. The largest the image can be is 300" (7.6 m) when the projector is about 384 inches (9.7 m) from the wall or 
screen.
300
240
Distance (Unit: m/inch)
Lens center
Screen Size...


2. Installation and Connections
[NP600S]
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is ap-
proximately 60" (1.52m) measured diagonally when the projector is roughly 35 inches (0.9 m) from the wall or screen. 
The largest the image can be is 110" (2.8 m) when the projector is abo\
ut 66 inches (1.7 m) from the wall or screen.
110
Distance 
(Unit: m/inch)
Lens center
Screen Size
Screen Size (Unit: cm/inch)...

4
2. Installation and Connections
[NP500WS]
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is ap-
proximately 57" (1.45m) measured diagonally when the projector is roughly 36 inches (0.9 m) from the wall or screen. 
The largest the image can be is 104" (2.6m) when the projector is abou\
t 66 inches (1.7 m) from the wall or screen.
104
Distance 
(Unit: m/inch
)
Lens center
Screen Size
Screen Size (Unit: cm/inch)...

5
2. Installation and Connections
C
α
B
D
Throw Distance and Screen Size
The  following  shows  the  proper  relative  positions  of  the  projector  and  screen.  Refer  to  the  table  to  determine  the 
position of installation.
Dstance Chart [NP600/NP500/NP400/NP00/NP500W]
B = Ver tical  distance  between  lens  center  and 
screen center
C =  Throw distance
D =  Ver tical  distance  between  lens  center  and 
screen  bottom  (top  of  screen  for  ceiling  ap-
plication)
α =  Throw...

6
2. Installation and Connections
[NP600S]
Screen SizeBCDαDiagonalWidthHeightwidewideinchmminchmminchmminchmminchmminchmmdegree60152448121936914205053589524829.464162651130038975215383895625129.47017785614224210672358941104925629.37719566215654611732664846115626129.38020326416264812192767347120336429.29022867218295413723075753135737129.210025408020326015243384159151137929.111027948822356616763692666166538729.1
[NP500WS]
Screen...

7
2. Installation and Connections
 Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode 
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power manage
-
ment...

8
2. Installation and Connections
• Select the source name for its appropriate input connector after turning on the projector.
Input connectorSOURCE button on the projector 
cabinetButton on the remote control
COMPUTER 1 IN COMPUTER1(COMPUTER 1)
COMPUTER 2(DVI-I)IN
 COMPUTER 2(DIGITAL)
or
 COMPUTER 2(ANALOG)
(COMPUTER 2)
	 ↓ (Toggle)
(COMPUTER 2)
NOTE: The projector is not compatible with video decoded outputs of the \
NEC ISS-6020 switcher.
NOTE: An image may not be displayed correctly when a...

9
2. Installation and Connections
When Viewing a DVI Digital Signal
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before 
turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the source menu before 
turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should 
this happen, restart your PC.
Do not disconnect the...

0
2. Installation and Connections
COMPUTER 1 IN COMPUTER 2 (DVI-I) IN
VGA signal cable  (supplied)
IBM PC or Compatibles (Notebook type) or Macintosh (Notebook type)
IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)
VGA signal cable (not supplied)
DVI to VGA adapter (supplied)
NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do so 
may cause damage to the connector of the projector.
Using Two Analog COMPUTER...


2. Installation and Connections
Connecting an External Monitor
You  can  connect  a  separate,  external  monitor  to  your  projector  to  simultaneously  view  on  a  monitor  the  computer 
analog image you’re projecting.
NOTE:
• Daisy chain connection is not possible.
•  When audio equipment is connected, the projector speaker is disabled.
AUDIO IN PHONE 
MONITOR OUT (COMP 1)
AUDIO OUT 
VGA signal cable (sup-plied)
VGA signal cable (not supplied)