Home > NEC > Projector > NEC Np510 Portable Projector User Manual

NEC Np510 Portable Projector User Manual

Here you can view all the pages of manual NEC Np510 Portable Projector User Manual. The NEC manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 41

32
3. Projecting an Image (Basic Operation)
FOCUS FOCUS
Zoom
[NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W]
Use	the	ZOOM	lever	to	adjust	the	image	size	on	the	screen.
Zoom Lever
[NP610S/NP510WS]
The	image	size	can	be	adjusted	electronically	from	the	menu. 	To	do	so,	follow	the	steps	below.
Adjusting from the menu
1.  Press the MENU button.
  The menu will be displayed.
2. Press the  button to select [SETUP] and press the ENTER button.
  The [GENERAL] tab will be highlighted.
 
3. Press the ...

Page 42

33
3. Projecting an Image (Basic Operation)
4. Use the  or  button to adjust the image size.
5.  After completing adjustment, press the EXIT button three times.
  The menu will be closed.
Focus
[NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W]
Use	the	FOCUS	ring	to	obtain	the	best	focus.
[NP610S/NP510WS]
Use	the	FOCUS	lever	to	obtain	the	best	focus.
FO CUS FOCUS
Focus Ring
FOCUSFOCUS
Focus Lever 

Page 43

34
3. Projecting an Image (Basic Operation)
 Correcting Keystone Distortion
Correcting Keystone Distortion
If	the	screen	is	tilted	vertically,	keystone	distortion	becomes	large.	Proceed	with	the	following
steps	to	correct	keystone	distortion
 
NOTE: 
•	 The	Keystone	correction	can	cause	an	image	to	be	slightly	blurred	because	the	correction	is	made	electronically.
•	 The	Keystone	correction	range	can	be	made	narrower,	depending	on	a	signal	or	its	aspect	ratio	selection.
Adjusting with buttons on the...

Page 44

35
3. Projecting an Image (Basic Operation)
Adjusting from the menu
1. Press the MENU button.
  The menu will be displayed.
2. Press the  button to select [SETUP] and press the ENTER button.
 
  The [GENERAL] screen will be displayed.
3. Press the  button to select [KEYSTONE].
 
4.  Press the  or  button.
  Adjust so that the image is rectangular.
5. After completing adjustment, press the EXIT button three times.
  The menu will be closed.
NOTE:	The	Keystone	correction	can	cause	an	image	to	be...

Page 45

36
3. Projecting an Image (Basic Operation)
Adjusting with the Auto Keystone Function
The	Auto	 Keystone	 correction	 feature	will	correct	 the	vertical	 distortion	 of	a	projected	 image	on	the	 screen. 	No	 special	
operation	required. 	Just	put	the	projector	on	a	flat	surface.
TIP:	Even	when	the	menu	setting	for	[AUTO	KEYSTONE]	is	turned	on,	[KEYSTONE]	can	be	adjusted	manually.
To	turn	on	[AUTO	KEYSTONE],	proceed	the	following	steps.
1. Press the MENU button
  The menu will be displayed.
2. Press the...

Page 46

37
3. Projecting an Image (Basic Operation)
 Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
Optimizing	a	computer	image	automatically.
Press	the	AUTO	ADJ.	button	to	optimize	a	computer	image	automatically.
This	adjustment	may	be	necessary	when	you	connect	your	computer	for	the	first	time.
[Poor picture]
[Normal picture]
VOLUMEL-CLICK
MOUSER-CLICK
ASPECT HELP FREEZE
PICTURE
AUTO ADJ.S-VIDEO VIDEOCOMPUTER
ECO MODE12
Increase volume
Decrease volume
VOLUME L-CLICK...

Page 47

38
3. Projecting an Image (Basic Operation)
7 Turning off the Projector
MENU
EXITENTER
STATUS
LAMP
AUTO ADJ.
SOURCEENTEREXIT
MENU
UP
MAGNIFY
PAGE
OFF
POWER ON
AV-MUTE
DOWN
To	turn	off	the	projector:
1.  First,  press  the   (POWER)  button  on  the  projector 
cabinet or the POWER OFF button on the remote con -
trol. 
  The  [POWER  OFF  /  ARE YOU  SURE?  /  CARBON  SAV-
INGS- SESSION 0.000[g-CO2]] message will appear.
2.  Secondly,  press  the  ENTER  button  or  press  the  
(POWER) or the POWER OFF...

Page 48

39
3. Projecting an Image (Basic Operation)
 After Use
Preparation:	Make	sure	that	the	projector	is	turned	off.
1. Unplug the power cable.
2.  Disconnect any other cables.
3.  Retract adjustable tilt foot if extended.
4.  Cover the lens with the lens cap.
5.  Put the projector and accessories in the supplied soft case.
  Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from 
damage.
NOTE:	The	NP610S,	the	NP510WS,	the	NP405,	and	the	NP305	do	not...

Page 49

40
1 Turning off the Image and Sound
Press	the	AV-MUTE	 button	to	turn	 off	the	 image	 and	sound	 for	a	short	
period of time. Press again to restore the image and sound.
NOTE:
•	 Even though the image is turned off, the menu still remains on the scree\
n.
•	 Sound	from	the	AUDIO	OUT	jack	(Stereo	mini)	can	be	turned	off.
 Freezing a Picture
Press	 the	FREEZE	 button	to	freeze	 a	picture. 	Press	 again	to	resume	
motion.
NOTE:	The	image	is	frozen	but	the	original	video	is	still	playing	back.
 Enlarging...

Page 50

41
4. Convenient Features
 Changing Eco Mode
This	feature	enables	you	to	select	two	brightness	modes	of	the	lamp:
OFF	and	ON	modes.	The	lamp	life	can	be	extended	by	turning	on	the	[ECO	MODE].
[ECO	MODE]DescriptionStatus	of	LAMP	indicator
[OFF]This	is	the	default	setting	(100%	Brightness).Off
ST ATUS
LAMP
[ON]Select this mode to increase the lamp life (approx. 
70%	
Brightness	 on	NP610/NP510W/NP410W/
NP610S/NP510WS 	and 	approx. 	80% 	Brightness	 on	
NP510/NP410/NP405/NP310/NP305). Steady Green light...
Start reading NEC Np510 Portable Projector User Manual

Related Manuals for NEC Np510 Portable Projector User Manual

All NEC manuals