NEC Np2000 Lcd Projector Users Manual

11
1. Introduction
Using the Remote Control in Wired Operation
Connect one end of the supplied remote cable to the REMOTE mini jack and the other end to the remote jack on the
remote control.
NOTE: Connecting the remote cable to the REMOTE mini jack on the terminal panel will make the wireless operation unavailable.
LASER3D REFORMAUTO ADJ.
ASPECT
HELP
PICTUREPIC-MUTELAMP MODER-CLICK L-CLICK
MOUSE
FREEZE
VOLUME MAGNIFYPAGESELECTMENUENTEREXIT
OFF
VIDEO
S-VIDEOVIEWER
LAN COMPUTERCOMPONENT
ONPOWER
POWER
3 1...

12
This section describes how to set up your projector and how to connect PCs, video and audio sources.
2. Installation and Connections

 Setting Up the Screen and the Projector
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 30 inches (0.76 m) measured diagonally when the projector is roughly 41 inches (1.0 m) from the wall
or screen. The largest the image can be is 500 inches (12.7 m) when the projector is about 718 inches...

13
2. Installation and Connections
 Making Connections
Connecting Your PC or Macintosh Computer
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode and
before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
*If the screen goes blank while using your remote control, it may be the result of the computers...

14
COMPUTER 3 IN
PHONE
AUDIO IN
2. Installation and Connections
When Viewing a DVI Digital Signal
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied)
before turning on your PC or projector. Turn on the projector first and select DVI (DIGITAL) from the source menu
before turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should
this happen, restart your...

15
2. Installation and Connections
COMPUTER 1 IN
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-
quired for this connection.
From the menu, select [Setup] → [Options] → [Signal Select] → [Computer 1] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-
connector.
NOTE: Audio signal is not available for this connection.
TIP: The ADP-SC1 SCART adapter is obtainable from your...

16
AUDIO
IN
AUDIO OUT
PHONE
MONITOR OUT COMPUTER 1 IN  (or COMPUTER 2 IN / COMPONENT IN)
2. Installation and Connections
Connecting an External Monitor
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
or component image youre projecting.
NOTE:
•Daisy chain connection is not possible.
•The MONITOR OUT connector will output no video signal (Digital signal) from the COMPUTER 3 IN connector.
•When audio equipment is connected, the projector...

17
AUDIO INLRAUDIO OUT
LR
Component
YCbCr
COMPONENT IN
AUDIO IN 
2. Installation and Connections
Connecting Your DVD Player with Component Output
DVD player Audio Equipment
Audio cable (not supplied)
Component video RCA
3
cable (not supplied)
TIP: A component signal will be automatically displayed. If not, from the menu, select [Setup] → [Options] → [Signal Select] →
[Computer 1 (or 2)] → [Component].
•When connecting to the COMPUTER 2 IN, use a commercially available RCA (female)-to-BNC(male) adapter....

18
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
S-VIDEO IN
VIDEO INAUDIO IN
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
Audio equipment
Audio cable (not supplied)
TIP: You can connect a video cable to the Y connector of the COMPONENT connectors to display a VCR source. To do so, from the
menu, select [Setup] 
→ [Options] → [Signal Select] → [Component] → [Video].
NOTE: Refer to your VCR or laser...

19
LAN
Connecting to a Network
The NP2000/NP1000 comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable.
Placing the optional wireless LAN card (NWL-100*) in the PC card slot of the projector also provides a wireless LAN
connection. To use a LAN connection, you are required to assign an IP address to the projector. For setting the LAN
mode, see page 89 (From the menu, select [Setup] → [Installation] → [LAN Mode])
With the LAN connection, two features are available:...

20
(B) Example of wireless LAN connection
(Network Type → Mode: Infrastructure)
2. Installation and Connections
To make connection with a wired LAN via an access point, you need to select the Infrastructure mode.
From the menu, select [Setup] → [Installation] → [LAN Mode] → [PC Card] → [Advanced] → [Network Type] →
[Mode] → [Infrastructure].
(C) Example of wireless LAN connection (Network Type → Mode: 802.11 Ad Hoc)
To enable direct communication (i.e., peer-to-peer) between personal computers and...